Loading ...
Loading ...
Loading ...
TheMaximumLengthoftheexhaust
systemdependsuponthetypeofduct
used,numberof elbowsandtypeof
"exhausthood.Themaximumlengthfor
bothrigidandflexibleductisshown
inchart.
EXHAUST DUCT LENGTHS (FEET)
EXHA IJST HOOD TYPE
Numberof
J
4" LOUVERED 2 1/2"
MAXIMUM LENGTH OF ,4-INCH DIAMETER
RIGID METAL DUCT
0 56' 56' 42'
1 46' 46' 36'
2 34' 34' 28'
3 32' 32' 18'
MAXlHUIM LENGTH OF 4-INCH DIARETER
pLEXlBLE METAl. DUCT
0 30' 30' 22'
1 22..... 22' 14'
2 16' 16' 10
3 10', 10' 5'
Exhaust Systems longer than specified
will:
• Shorten the life of the obeyer.
• Reduce the performance, such as
cause longer drying times and
increases the use of energy.
• Accumulate lint.
The Laundry Center may be exhausted
four (4) ways with rear flush
installation:
1. Straight back.
2. Down (8" length of 4" rigid duct
andl elbow down).
3. Left (8" length of 4" rigid duct, 1
elbow down and 1 ,elbow left).
4. Right (8" length Qf4" rigid duct, 1
elbow down and 1 _rlbow right).
To exhaust up, add axz"11" length of
standard 4" diameter duct and a 90°
elbow. The unit will be positioned
about 4-1/2" away from the wall (flush
to wall exhausting may be done by
going below the dryer then sideways).
Water supply and drain
requirements
Hot and Cold water faucets within 4
feet of back of the Laundry Center and
enough pressure (5-100 PSI) are
required.
Water Heater should be set to deliver
130°E or above water to the washer
for best results.
To drain the Laundry Center washer,
you need either a 20-gallon laundry
tub or IL-1/4inch diameter standpipe
having a minimum carry-away
capacit 7 of 16 gallons per minute. The
minimum tub or standpipe height is
33 inches from the bottom of the
washer. The maximum tub or
standpipe height is 96 inches from the
bottom of the washer. For installations
requiring a longer drain hose, have a
qualified technician install a longer
hose, P/N 131461201. For drain
systems in the floor, install a siphon
break kit, P/N 076660-000. Both
components are available from Sears
Parts Department.
PLEASE
BEGIN...
(c)
(d)
(e)
(0
Remove:
(a) foam tub blocking pad;
(b) foam shipping blocks
from rear of unit;
tape from dryer door;
foam dryer support pads;
inlet hoses.
From the back of the washer,
remove the wire shipping clips
securing the drain hose and power
cord. Plastic clamps secure the
drain hose to the right side of the
washer backsheet. These clamps
form a standpipe to prevent water
siphoning. DO NOT REMOVE
THESE CLAMPS.
Tub Blocking Pad
Dryer Support Pads
Using the four shipping carton comer
posts (two on each side), carefully lay
the Lannda2/Center on its left side and
remove the..foam shipping base.
Plastic
Spacer
Block Shipping
_._ Blocks
Mechanism "t_i_ ___,
Shipping g°'t I _]_'_"-_o[I 1
Shipping
Clips
P_D_ain Cord
Hose
ShippingCarton
Corner Posts
Using the ratchet with 3/8 inch socket,
remove n_techanism shipping bolt.
Remove plastic spacer block from
center of base using adjustable pliers.
NOTE: If the Laundry Center is to be
transported at a later date, the tub
blocking p'.._d,shipping bolt and plastic
spacer block should be retained.
._Tub
t'_'_- "_ _ _.,._Blocking
"_ _ Pad
| Shipping
Spacer p#"_ _ Bolt
BlOCk_._" t" I
Return Laundry Center to upright
position.
Page 4
Loading ...
Loading ...
Loading ...