Loading ...
Loading ...
Loading ...
6
6.
Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the
¹⁄₄
in. drilled hole
in the water pipe and that the washer is under the pipe clamp.
Tighten the packing nut. Tighten the pipe clamp screws
carefully and evenly so washer makes a watertight seal. Do
not overtighten or you may crush the copper tubing.
7.
Slip the compression sleeve and compression nut on the
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten.
8.
Place the free end of the tubing in a container or sink, and
turn ON the main water supply. Flush the tubing until water is
clear. Turn OFF the shutoff valve on the water pipe. Coil the
copper tubing.
Connecting to Refrigerator
1.
Attach the copper tube to the valve inlet using a compression
nut and sleeve as shown. Tighten the compression nut. Do
not overtighten. Use the tube clamp on the back of the
refrigerator to secure the tubing to the refrigerator as shown.
This will help prevent damage to the tubing when the
refrigerator is pushed back against the wall.
2.
Turn shutoff valve ON.
3.
Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.
4.
The ice maker is equipped with a built-in water strainer. If
your water conditions require a second water strainer, install
it in the
¹⁄₄
in. (6.35 mm) water line at either tube connection.
Obtain a water strainer from your nearest appliance dealer.
5.
Plug in refrigerator or reconnect power.
Refrigerator Doors: Removing,
Reversing (optional) and Replacing
TOOLS NEEDED:
⁵⁄₁₆
in. hex-head socket wrench, No. 2 Phillips
screwdriver, flat-head screwdriver,
⁵⁄₁₆
in. open-end wrench, flat 2
in. putty knife.
IMPORTANT:
■
Before you begin, turn the refrigerator control OFF, unplug
refrigerator or disconnect power. Remove food and any
adjustable door or utility bins from doors.
■
If you are only removing and replacing the doors, the
instructions are the same regardless of door style. See
the “Door and hinge removal” and “Door and hinge
replacement” sections.
■
Depending on your model, you may have standard (Style
1) or contour (Style 2) doors. If you are also going to
reverse the door swing, follow the instructions for the
appropriate door style.
■
All graphics referenced in the following instructions are
included later in this section after “Final Steps.”
Door and Hinge Removal
⁵⁄₁₆
” Hex-Head Hinge Screw
1.
Unplug refrigerator or disconnect power.
2.
Open refrigerator door and remove base grille from the
bottom front of the refrigerator (see Base Grille graphic).
3.
Close the refrigerator door and keep both doors closed until
you are ready to lift them free from the cabinet.
NOTE:
Provide additional support for the doors while the
hinges are being moved. Do not depend on the door magnets
to hold the doors in place while you are working.
4.
Remove the parts for the top hinge as shown in Top Hinge
graphic. Lift the freezer door free from the cabinet.
5.
Remove the parts for the center hinge as shown in the Center
Hinge graphic. Lift the refrigerator door free from the cabinet.
6.
Remove the parts for the bottom hinge as shown in the
Bottom Hinge graphic.
IMPORTANT:
If you want to reverse your doors so that they open
in the opposite direction, continue with the “Door reversal
(optional)” instructions. If you are not reversing the doors, see the
“Door and Hinge Replacement” section.
1. Tube Clamp
2. Copper Tubing
3. Compression Nut
4. Valve Inlet
Loading ...
Loading ...
Loading ...