Loading ...
Loading ...
Loading ...
9
Changing Cycles, Modifiers,
and Options
You can change Sensor and Timed Cycles, Modifiers, and Options
anytime before pressing Start.
■ Three short tones sound if an unavailable combination is
selected. The last selection will not be accepted.
Changing Cycles after pressing Start
1. Press POWER/CANCEL.
2. Select the desired c
ycle and options.
3. Pre
ss START/PAUSE. The dryer starts at the beginning of the new
cycle.
NOTE: I
f you do not press Start/Pause within 5 minutes of selecting
the cycle, the dryer automatically shuts off.
Changing Modifiers and Options after pressing Start
You can change an Option or Modifier anytime before the selected
Option or Modifier begins.
1. Pre
ss START/PAUSE.
2. Select the new Option and/or Modifier
.
3. Press START/PAUSE to continue the cycle.
Changing the Preset Dryness Level Settings
If all of your loads on all Sensor cycles are consistently not as dry as
you would like, you may change the preset Dryness Level settings to
increase the dryness. This change will affect all of your Sensor
cycles.
Your Dryness Level settings can be adjusted t
o adapt to different
installations, environmental conditions, or personal preference.
There are 3 drying settings: 1 (factory preset dryness level), 2 (slightly
dry
er clothes, approximately 15% more drying time) and 3 (much
dry
er clothes, approximately 30% more drying time).
1. T
he Dryness Level settings cannot be changed while the dryer is
running.
2. Pre
ss and hold the DRYNESS LEVEL button for 5 seconds. The
dryer will beep, and “CF” will be displayed for 1 second
follo
wed by the current Dryness Level setting.
3. T
o select a new Dryness Level setting, press the DRYNESS LEVEL
button again until the desired Dryness Level setting is shown.
NOTE: While c
ycling through the settings, the current setting
will not flash, but the other settings will flash.
4. Press ST
ART/PAUSE to save the Dryness Level setting.
The Dryness Level setting you selected will become y
our new preset
Dryness Level setting for all Sensor cycles.
Drying Rack Option
Use the Drying Rack to dry items such as sweaters and pillows
without tumbling. The drum turns, but the drying rack does not
move.
If your model does not have a drying rack, you may be able to
pu
rchase one for your model. To find out whether your model allows
drying rack usage and for information on ordering, please refer to the
front page of the manual or contact the dealer from whom you
purchased your dryer.
NOTE: T
he drying rack must be removed for normal tumbling. Do
not use the automatic cycle with the drying rack.
To use the drying rack
1. Open
dryer door.
A
A. Front edge
2. Place drying rack inside dryer drum, positioning the back wire
on the ledge of the inner dryer back panel. Push down on front
edge of drying rack to secure at the front of the dryer.
A
B
A. Drying rack front edge
B. Dryer back panel
3. Put the wet items on top of the drying rack. Leave space between
the items so air can reach all the surfaces.
NOTE: Do not allo
w items to hang over the edge of the drying rack.
4. Close the door.
5. Press the PO
WER/CANCEL button.
6. Select a T
imed Dry cycle and temperature (see following chart).
Items containing foam, rubber, or plastic must be dried on a
clothesline or by using the Air Fluff temperature setting.
7. Y
ou must select a time by pressing TIME ADJUST + (plus) or –
(minus). Reset time as needed to complete drying. Refer to the
following table.
8. Press START/PAUSE.
Loading ...
Loading ...
Loading ...