Loading ...
Loading ...
Loading ...
9
HOT SURFACE
TURBO BOIL
FLEX
3
4
6
7
8
2
TURBO
BOIL
MED
WARM &
SIMMER
OFF
8
2
4
6
3
7
MED
OFF
LO
HI
8
2
4
6
3
7
MED
OFF
LO
HI
8
8
6
6
4
4
2
2
LO
LO
OFF
HI
HI
DOUBLE
SINGLE
8
8
6
6
4
4
2
2
LO
LO
OFF
HI
HI
DOUBLE
SINGLE
HOT SURFACE
TURBO BOIL
FLEX
8
2
4
6
3
7
MED
OFF
LO
HI
8
8
6
6
4
4
2
2
LO
LO
OFF
HI
HI
DOUBLE
SINGLE
3
4
6
7
8
2
TURBO
BOIL
MED
WARM &
SIMMER
OFF
8
8
6
6
4
4
2
2
LO
LO
OFF
HI
HI
DOUBLE
SINGLE
Radiant surface elements may appear to
have cooled after they have been turned off . A hot surface
indicator light will come on and will continue to glow until
the glass cooktop has cooled down to a moderate level. The
glass surface may still be hot and burns may occur if the
glass surface is touched before the indicator light has turned
off .
Do not place plastic items such as salt and
pepper shakers, spoon holders or plastic wrappings on
cooktop when it is in use. These items could melt or ignite.
Potholders, towels or wooden spoons could catch fi re if
placed too close to the surface elements.
Do not allow aluminum foil, or ANY
material that can melt to make contact with the ceramic
glass cooktop. If these items melt on the cooktop they will
damage the ceramic cooktop.
Figure 1
Figure 2
Setting Surface Controls
Operating the Dual Surface Radiant Element
The cooktop is equipped with a dual radiant surface element located
at the RIGHT & LEFT FRONT position (See Figures 1 & 2). Symbols
on the control knob area are used to indicate which coil of the dual
radiant element will heat. The SINGLE marking indicates that only
the inner coil will heat (Figure 3). The DOUBLE marking indicates
that both inner and outer coils will heat (Figure 4). You may switch
between settings at any time during cooking.
To Operate the Dual Surface Element:
1. Place correctly sized cookware on the dual surface
element.
2. Push in and turn the control knob counterclockwise (See
Figure 3) for smaller cookware or clockwise (See Figure
4) for larger cookware.
3. Turn the knob to adjust the setting if needed. Start most
cooking operations on a higher setting and then turn to
a lower setting to fi nish cooking. Each surface element
provides a constant amount of heat at each setting. A
glowing red surface heating area extending beyond the
bottom edge of the cookware indicates the cookware is
too small for the surface heating area.
4. When cooking has completed, turn the surface control
knob to OFF before removing the cookware. Note:
The Hot Surface Indicator light will come on when the
control knob is turned on and will continue to glow until
the glass cooktop has cooled down to a moderate level
that will not cause burns if the area is touched. The light
may remain on even though the controls are turned OFF.
Note: See Table on page 7 for recommended control
settings.
Figure 3
Single Setting
Figure 4
Dual Setting
Dual Radiant heating areas on ceramic smooth top
(shown in black)
8
8
6
6
4
4
2
2
LO
LO
OFF
HI
HI
DOUBLE
SINGLE
8
8
6
6
4
4
2
2
LO
LO
OFF
HI
HI
DOUBLE
SINGLE
Loading ...
Loading ...
Loading ...