Loading ...
Loading ...
Loading ...
6
HOT SURFACE
TURBO BOIL
FLEX
3
4
6
7
8
2
TURBO
BOIL
MED
WARM &
SIMMER
OFF
8
2
4
6
3
7
MED
OFF
LO
HI
8
2
4
6
3
7
MED
OFF
LO
HI
8
8
6
6
4
4
2
2
LO
LO
OFF
HI
HI
DOUBLE
SINGLE
8
8
6
6
4
4
2
2
LO
LO
OFF
HI
HI
DOUBLE
SINGLE
HOT SURFACE
TURBO BOIL
FLEX
8
2
4
6
3
7
MED
OFF
LO
HI
8
8
6
6
4
4
2
2
LO
LO
OFF
HI
HI
DOUBLE
SINGLE
3
4
6
7
8
2
TURBO
BOIL
MED
WARM &
SIMMER
OFF
8
8
6
6
4
4
2
2
LO
LO
OFF
HI
HI
DOUBLE
SINGLE
Setting Surface Controls
About the Ceramic Glass Cooktop
The ceramic cooktop has radiant surface elements
located below the surface of the glass. The design of the
ceramic cooktop outlines the area of the surface element
underneath. Make sure the diameter of the pan matches the
diameter of the element outline on the cooktop.
Heat is transferred up through the surface of the cooktop
to the cookware. Only fl at-bottom cookware should be
used. The type and size of cookware, the number of surface
elements in use and their settings, are all factors that will
aff ect the amount of heat that will spread to areas beyond
the surface elements. The areas surrounding the elements
may become hot enough to cause burns.
About the Radiant Surface Elements
The element temperature rises gradually and evenly. As the
temperature rises, the element will glow red. To maintain
the selected setting, the element will cycle on and off . The
heating element retains enough heat to provide a uniform
and consistent heat during the off cycle. For energy effi cient
cooking, turn off the element several minutes before cooking
is complete. This will allow residual heat to complete the
cooking process.
Locations of the Radiant Surface Elements and
Controls
Your cooktop is equipped with radiant surface burners with
diff erent wattage ratings. The ability to heat food quicker
and in larger volumes increases as the element wattage
increases.
The radiant surface elements are located on the 30”
cooktop as follows (See Figure 1):
• One 9 inch Turbo Boil Flex
TM
radiant element located at
the left rear position;
• One 6 inch single radiant element located at the right
rear position;
• One 9 or 12 inch dual radiant element located at the
right front position;
• One 5 or 7 inch dual radiant element located at the left
front position.
The radiant surface elements are located on the 36”
cooktop as follows (See Figure 2):
• Two 6 inch radiant elements located at the center and
right rear position;
• One 9 inch Turbo Boil Flex
TM
radiant element located at
the left rear position;
• One 9 or 12 inch dual radiant element located at the
right front position;
• One 5 or 7 inch dual radiant element located at the left
front position.
NOTE: Please read detailed instructions for ceramic glass
cooktop cleaning in the General Care & Cleaning section
and Before You Call checklist section of this Use and
Care Guide.
NOTE: Radiant elements have a limiter that allows the
element to cycle on and off , even at the HI setting. This
helps to prevent damage to the ceramic cooktop. Cycling
at the HI setting is normal and will mostly occur if the
cookware is too small for the radiant element or if the
cookware bottom is not fl at (For information concerning
cookware, refer to use proper cookware on page 7 of
this Use and Care Guide)
30” Cooktop - Location of the
Radiant Surface Elements and Controls
Figure 1
36” Cooktop - Location of the
Radiant Surface Elements and Controls
Figure 2
Loading ...
Loading ...
Loading ...