SLA 290
EN User Manual A4 Laminator SLA 290
2 EN
EN
Copyright © 2025, Fast ČR, a. s.
Revision 01/2025
IMPORTANT SAFETY INFORMATION
Read all instructions before using.
• This appliance is not intended for use by persons (including children) with reduced phy-
sical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that they do not play
with the appliance.
• Carefully remove all packaging materials and dispose of correctly.
• Always operate this product on a fl at surface.
• Do not operate under or near curtains or other combustible materials.
• Do not place the appliance near a heat source or in direct sunlight.
• Do not place fi ngers, hair, loose clothing and jewellery near the pouch entry hole as
serious injury may occur.
KNOW YOUR APPLIANCE
• Follow all warnings and instructions marked on the product.
• Cardboard carrier pouches must not be used with this laminator as it may cause jamming
or damage to the laminator.
• The objects to be laminated cannot be metal or plastic objects (iron, copper, aluminum
etc.).
• Do not insert anything into the machine other than laminating pouches.
• The machine is only to be used for laminating.
• The top of the laminator will become hot during use, please do not touch.
• Do not block the pouch exit hole or the pouch will jam inside the machine and cause a
hazard.
USING YOUR LAMINATOR
1. Remove the laminator from the packaging and unwind the cord to its full length.
2. Put the laminator on a flat surface. Ensure there is enough space at the front and back of
the laminator when in use for pouches to pass through without obstruction.
3. Plug the machine into a suitable power supply outlet.
4. Ensure the ON/OFF switch is in OFF position before plugging in the laminator.
5. Ensure the pouch tray is open before inserting the laminating pouch.
COLD LAMINATION
• Turn on power and press the “Pouch Selection Button” to select ‘Cold’ mode to start the
cold lamination, the blue LED will stop fl ashing and stay steady when ready for cold
lamination.
EN 3
EN
Copyright © 2025, Fast ČR, a. s.
Revision 01/2025
NOTE:
• Ensure the machine is cool when using Cold lamination.
• Do NOT use cold lamination if the machine has just completed a Hot/thermal lamination
job.
HOT LAMINATION
• Press the “Pouch Selection Button” to select the correct ‘Hot’ mode according to the
thickness of the thermal laminating pouch, the machine is designed with plug & play
feature, the blue LED illuminates and stays steady instantly. The machine could be used
to laminate thermal laminating pouches immediately.
• Prepare the laminating pouch for inserting into the machine. Load the paper centrally into
the pouch against the pre-sealed edge.
• Do not use pouches thicker than 125 micron.
NOTE:
• Ensure the sealed edge of the laminating pouch is inserted into the laminator fi rst, other-
wise it may cause the machine to jam.
• The pouch will move through the machine and exit at the other side. Take out the pouch
immediately. Do NOT leave it in laminator for more than 3 seconds.
• Turn the laminator off after use and unplug it.
Attention:
• Do NOT laminate heat sensitive paper.
• For optimal lamination performance, the suitable room temperature is 18~25
o
C.
Clear A Jammed Pouch
This laminator is designed with anti-jamming technology. In the case of a mis-feed occu-
rring, first turn the laminator off, then press the Jam Release Lever and pull the pouch out
manually.
CLEANING & MAINTENANCE
• Unplug the laminator when not in use or before moving or cleaning.
• Wipe clean with a dry cloth.
• Do not spray any fl ammable gas or oil on this laminator, it may cause a fi re.
• If the power supply cord is damaged it must be replaced by a qualifi ed electrician to
avoid a hazard.
• Never remove the cover or dismantle the machine, no serviceable parts inside.
4 EN
EN
Copyright © 2025, Fast ČR, a. s.
Revision 01/2025
PRODUCT SPECIFICATION
Model SLA 290
Max. Lamination Width A4 (240 mm)
Number of Rollers 4
Laminating Thickness 80/100/125 micron
Max Document Thickness 0.6 mm
Laminating Options Cold and Thermal Pouches
Anti-Jam Feature Yes
Auto Shut Off 60 min after the last button touch
Power Supply 240V~ 50Hz
Rated Current 8.0 A
Power Consumption 1920 W
Warm Up Time 0 seconds
Laminating Speed 300 mm/min
Net Weight 1.73 kg
Dimension (L*W*H) 395*125*70 mm
EN 5
EN
Copyright © 2025, Fast ČR, a. s.
Revision 01/2025
INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING
MATERIALS
Dispose of packaging material at a public waste disposal site.
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC APPLIANCES
The meaning of the symbol on the product, its accessory or packaging indicates
that this product shall not be treated as household waste. Please, dispose of
this product at your applicable collection point for the recycling of electrical &
electronic equipment waste. Alternatively in some states of the European Union
or other European states you may return your products to your local retailer when
buying an equivalent new product. The correct disposal of this product will help
save valuable natural resources and help in preventing the potential negative
impact on the environment and human health, which could be caused as a result
of improper liquidation of waste. Please ask your local authorities or the nearest
waste collection centre for further details. The improper disposal of this type of
waste may fall subject to national regulations for fines.
For business entities in the European Union
If you wish to dispose of an electrical or electronic device, request the necessary
information from your seller or supplier.
Disposal in other countries outside the European Union
If you wish to dispose of this product, request the necessary information about the
correct disposal method from local government departments or from your seller.
The product meets EU requirements.
Changes to the text, design and technical specifications may occur without prior notice and we
reserve the right to make these changes.
Manufacturer: Fast ČR, a.s., U Sanitasu 1621, CZ 251 01 Říčany
6 EN
EN
Copyright © 2025, Fast ČR, a. s.
Revision 01/2025
EN
Warranty conditions
Warranty card is not apart of the device packaging.
This product is warranted for the period of 24 months from the date of purchase to the end-user. Warranty
is limited to the following conditions. Warranty is referred only to the customer goods using for common
domestic use. The claim for service can be applied either at dealer’sshop where the product was bought, or
at below mentioned authorized service shops. The end-user is obligated to set up aclaim immediately when
the defects appeared but only till the end of warranty period. The end user is obligated to cooperate to certify
the claiming defects. Only completed and clean (according to hygienic standards) product will be accepted.
In case of eligible warranty claim the warranty period will be prolonged by the period from the date of claim
application till the date of taking over the product by end-user, or the date the end-user is obligated to take it
over. To obtain the service under this warranty, end-user is obligated to certify his claim with duly completed
following documents: receipt, certificate of warranty, certificate of installation.
This warranty is void especially if apply as follows:
Defects which were put on sale.
Wear-out or damage caused by common use.
The product was damaged by unprofessional or wrong installation, used in contrary to the applicable
instruction manual, used in contrary to legal enactment and common process of use or used for another
purpose which has been designed for.
The product was damaged by uncared-for or insufficient maintenance.
The product was damaged by dirt, accident of force majeure (natural disaster, fire, and flood).
Defects on functionality caused by low duality of signal, electromagnetic field interference etc.
The product was mechanically damaged (e.g. broken button, fall).
Damage caused by use of unsuitable media, fillings, expendable supplies (batteries) or by unsuitable
working conditions (e.g. high temperatures, high humidity, quakes).
Repair, modification or other failure action to the product by unauthorized person.
End-user did not prove enough his right to claim (time and place of purchase).
Data on presented documents differs from data on products.
Cases when the claiming product cannot be indentified according to the presented documents (e.g. the
serial number or the warranty seal has been damaged).
Manufacturer:
FAST ČR, a.s., U Sanitasu 1621, Říčany 251 01, Czech Republic
info@sencor.com
Authorized service centers:
Visit www.sencor.com for detailed information about authorized service centers.
The original version of the instructions is in the Czech language, other language versions are made by the
appropriate translation.
