SMS 7500BK
EN
MEN´S SHAVER
Translation of the original manual
SMS 7500BK
A
2
1
3
4
5
6
7
8
9
B
1
2
3
4
C
D
E
- 1 - 01/2025
2025, .
EN
Men´s Shaver
User Manual
Important Safety Instructions
READ CAREFULLY AND STORE FOR
FUTURE USE.
General Warnings
• This appliance may be used by
children 8 years of age and older and
by persons with physical or mental
impairments or by inexperienced
persons, if they are properly supervised
or have been informed about how to
use the product in asafe manner and
understand the potential dangers.
• Children must not play with the
appliance.
• Cleaning and maintenance performed
by the user must not be performed by
unsupervised children.
ELECTRIC RAZOR
- 2 - 01/2025
2025, .
• In the event that the charging cable
is damaged, have it repaired at
aprofessional service centre to prevent
causing adangerous situation. It is
forbidden to use the appliance if it has
adamaged charging cable.
This appliance can be washed
under awater tap.
Warning:
Before cleaning with water, make
sure that the appliance is turned off
and disconnected from the power
source.
• The parts of the appliance that need
to be mounted or stood upright, must
be mounted or stood upright in such
away that they cannot fall into water.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
- 3 - 01/2025
2025, .
Additional Important Safety Instructions forUse of the Appliance
• Before connecting the appliance to apower source, make sure that the voltage
indicated on the rating plate matches the voltage of the power source.
• Use the appliance only with the supplied charging cable. To avoid adangerous
situation, never use adifferent type of cable.
• Keep the charging cable dry.
• Do not place the charging cable over sharp objects. Make sure that it does not
hang over the edge of atable or touch aheated surface.
• Do not wrap the charging cable around the handle of the appliance.
• Do not connect or disconnect the charging cable with wet or damp hands.
• Store, charge and use the appliance at an ambient temperature of 15°C to 35°C.
Do not charge the appliance for longer than is necessary for it to fully charge.
• Once it is charged, disconnect it from the power source.
• Do not expose the appliance to temperatures higher than 50°C. Otherwise, the
built-in battery could be damaged.
• The appliance is equipped with abuilt-in long-life battery that can only be
removed at aprofessional service centre. Never attempt to remove it from the
appliance yourself.
Attention:
Never disassemble the appliance for the purpose of removing the
battery. Never short circuit the appliance or throw it into afire. Incorrect
use, risks releasing toxic substances or causing afire or explosion.
• Do not charge, use or store the appliance or leave it lying in abathroom or in
locations where it could fall into abath, wash basin or other containers filled
with water.
• In the event that the appliance falls into water, under no condition reach for it,
rather, immediately disconnect the power adapter from the power socket.
• Never use an appliance or power adapter that was submerged in water. Hand it
over to an authorised service centre for inspection.
• This electric shaver is intended for home use only and is designed for shaving
and trimming beards or whiskers and facial hair. The electric shaver is not
intended for commercial purposes or for trimming animal fur.
• Only use the electric shaver on dry, clean beards or whiskers. Do not use it on
wet beards or whiskers on which ashaving foam or gel, etc. is applied.
• We do not recommend using the electric shaver on parts of the face where there
are open wounds or lacerations, burns, blisters, etc.
• For hygiene reasons, the electric shaver should be used only by asingle user.
• Use the electric shaver in accordance with the instructions contained in this
user‘smanual.
- 4 - 01/2025
2025, .
• Use only the original accessories supplied with this electric shaver.
• The electric shaver and its power adapter must only be used in indoor areas.
Do not use it outdoors.
• Do not use the electric shaver in rooms where aerosol sprays are used or where
oxygen is administered.
• Do not expose the electric shaver to the outdoor environment, extreme
temperatures, direct sunlight, excessive humidity or excessively dusty
environments.
• Do not place the electric shaver near heaters, open fires or other sources of heat.
Warning:
Keep the electric shaver dry.
• Before every use, check the shaving head for damage. Never use an electric
shaver with adamaged shaving head.
• The electric shaver may heat up during use or when it is being charged.
This is completely normal.
• Keep the electric shaver at asafe distance from eyes.
• Always turn off the electric shaver and disconnect it from the power socket when
not using it, when leaving it without supervision, before cleaning, maintenance or
storage. Store the electric shaver and its power adapter in adry environment.
• Keep the electric shaver clean. Perform cleaning and maintenance according to
the instructions in chapter Cleaning and maintenance.
• Do not perform any maintenance on the electric shaver other than cleaning the
individual components as described in chapter Cleaning and maintenance.
• Never use an electric shaver or power adapter that are damaged in any way.
• Do not use the electric shaver if it has fallen on the floor, if it was submerged in
water, if it is not functioning correctly or if it is damaged in any other way.
• In order to prevent ahazardous situation from arising, do not repair the electric
shaver or any of its accessories yourself or modify it in any way. For all repairs,
contact an authorised service centre. By tampering with the product you risk
voiding your legal rights arising from unsatisfactory performance or quality
warranty.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EXPLANATION OF SYMBOLS PLACED ON THE PRODUCT OR INTHE
ACCOMPANYING DOCUMENTATION
The product meets all the basic requirements of the applicable EU
directives.
- 5 - 01/2025
2025, .
Used electrical andelectronic products must not be added to ordinary
municipal waste.
Used accumulators and batteries do not belong in normal municipal
waste.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
- 6 - 01/2025
2025, .
• Thank you for purchasing our
SENCOR product; we hope it will
serve to your satisfaction.
• Prior to using this appliance, please
read the user manual thoroughly,
even in cases when you are already
familiar with the use of similar types
of appliances. Use the appliance only
as described in this user manual.
Keep the manual for future reference.
If you pass the appliance on to
another person, ensure that this user
manual is included.
• Carefully unpack the appliance and
make sure not to discard any part
of the packaging material until you
have found all its components. It is
recommended to keep the original
packaging, packing material, receipt
and confirmation of the extent of the
seller'sliability or warranty certificate
at least for the duration of the legal
right of defective performance or
quality guarantee. When transporting
the appliance, we recommend
packaging it again in the original box
provided by the manufacturer.
DESCRIPTION OF THE ELECTRIC
RAZOR AND ITS ACCESSORIES
A1 Shaving cutters
A2 Shaving head with cutter holder
A3 On/Off switch
A4 Display
A5 Socket for connecting the power
cable
EN
Men´s Shaver
User Manual
A6 Protective cover
A7 Charging cable
A8 Cleaning brush
A9 Charging stand
DESCRIPTION OF THE DISPLAY
B1 Setting indicator
B2 Cleaning indicator
B3 Charging indicator
B4 Lock indicator
PURPOSE OF USE
• The electric razor is designed for
dry and wet shaving beards and
trimming sideburns, moustaches
or smaller hairs. The electric razor
is not intended for wet shaving or
cutting artificial hair or animal hair.
CHARGING
• The electric razor is equipped with
abuilt-in battery that allows cordless
operation of the razor.
• Allow the battery of the electric razor
to fully charge first without turning
it on before first use or after along
period of non-use.
• The electric razor can be charged in
two ways:
1. charging via aUSB cable
andexternal devices (such as
acomputer, power bank, etc.); or
2. charging via charging stand.
- 7 - 01/2025
2025, .
• Insert the smaller USB connector
into the socket on the underside
of the electric razor and the larger
connector into the selected power
source.
• The electric razor will start charging
when connected to apower source.
The charging indicator lights up.
• The charging time differs
dependingon the current charge
level of the battery. If the battery is
completely flat, it may take up to
1.5hours to charge.
• The charging indicator will flash red
when the charging level is 0–20%.
The charging indicator will flash
white when the charging level
reaches 20–100%.
• When the electric razor is fully
charged, the charging indicator lights
up white.
• Disconnect the charged electric
razor from the power source.
Warning:
Do not leave the electric
razor connected to themains
for longer than it takes to
fully charge it.
Fully charged electric razor will provide
approximately 60minutes of operation.
Then the electric razor needs to be
recharged.
DIRECT DRIVE TECHNOLOGY
• If the battery of the electric razor is
discharged or if it discharges during
operation, the electric razor can
be connected to the power supply
andcontinue to use it. This is made
possible thanks to the DIRECT
DRIVE technology that the electric
razor is equipped with. Thus, it is not
necessary to wait for aminimum
battery charge.
RECOMMENDATIONS FOR
EXTENDING BATTERY LIFE
• To keep the built-in battery working
for as long as possible, charge, use
andstore the electric razor at an
ambient temperature of 15–35°C
inadry environment. Lower or
higher temperatures adversely affect
the life of the battery.
• Do not wait until the battery is
completely discharged. It is better to
recharge the battery before they are
fully discharged.
• If you do not use the electric razor
for along time, charge the battery at
least once every 6months.
OPERATION
Shaving
• Turn the electric razor on by pressing
the On/Off switch.
• Hold the electric razor at aright
angle to the surface of the skin and
in short circular movements sweep
the shaving head over the skin of the
face in the opposite direction to the
growth of the beard. Apply adequate
pressure to the skin. Do not push
too hard.
• In more difficult to reach places, such
as on the chin, stretch the skin with
your free hand. This will give you
abetter shaving result.
- 8 - 01/2025
2025, .
Speed setting
• The electric razor has two speed
modes. Press the on/off switch for
1second to switch.
When the mode is switched
successfully, abeep will sound.
Note:
Your skin andbeard may
take up to three weeks to
get used to the new way of
shaving. Inthis period it is
recommended to use the
electric razor daily.
• When you have finished shaving,
clean the electric razor according to
the instructions in the Cleaning and
Maintenance chapter.
Low Battery Indicator
• When you turn on the electric razor,
the charge indicator will be lit or
flashed according to the charge
level:
• charge level ≥ 20%: the charging
indicator will light up white;
• charge level ≥ 5–20%: the charging
indicator will light up red;
• charge level ≤ 5%: the charging
indicator will start flashing red.
Shaving Head Cleaning Indicator
• The electric razor is equipped with
atimer that sums up the operating
time of the electric razor (shaving
time). After 10minutes, the cleaning
indicator will light up and abeep
will sound to remind you to clean
the shaving head. Insuch an event,
clean the electric razor as soon as
possible according to the chapter
Cleaning the Shaving Head.
Travel Lock
• The travel lock protects against
accidental switching on of the
electric razor, e.g. during its
transport.
• To activate the travel lock, press
andhold the on/off switch until the
lock indicator is lit on the display.
On/Off switch does not respond to
normal press.
• To deactivate the travel lock, press
andhold the on/off switch again.
The lock indicator will first blink
andthen turn off. Now the electric
razor is ready for use again.
CLEANING AND MAINTENANCE
• For hygiene reasons, clean the
electric razor after each use. Regular
cleaning is also important to ensure
proper operation of the electric razor
andextends the life of the shaving
cutters.
• Please turn the electric razor off
before cleaning it. Never clean the
electric razor when it is plugged into
the power supply to recharge.
• Do not use hard-bristled brushes,
abrasive cleaners, thinners, etc.
Otherwise the surface to be cleaned
may be damaged.
Cleaning the Body of the Electric Razor
• The electric razor body can be
cleaned using aclean dry wiping
cloth. Inthe event of heavy soiling,
you can use aslightly damp cloth.
Clean the surface then properly
wipe dry.
- 9 - 01/2025
2025, .
Cleaning the Shaving Head
• Brush off any remaining beard or
hair from the shaving head, including
the shaving cutters.
• Pull upwards to remove the razor
head from the razor body (Fig. C).
Using abrush, remove dirt and
beard residue from the shaving head
attachment area (Fig. D).
• Insert the shaving head back into
the holder.
Cleaning with Water
• Turn the electric razor upside down
andimmerse the electric razor head
in water. Switch on the electric razor
by pressing the on/off switch andlet
it run for approximately 30seconds.
Then turn off andremove the head
from thewater.
• Dry the shaving head with afine
cloth or allow it to dry naturally.
Do not use paper towels or coarse
cloths for drying, because they could
damage the shaving blades.
Warning:
Never immerse the electric
razor body in water. Risk of
serious electric shock!
For thorough cleaning, the shaving
head can be removed by pulling on
the holder andthen also by removing
the holder from the razor body (Fig. E).
Then wash both parts under running
water andallow them to dry completely
andthen insert them back into the body
of the electric razor.
TECHNICAL SPECIFICATIONS
Electric Razor
Input voltage ....................................... 5 V/1 A
Built-in battery .........................Li-Ion, 3.7 V,
800 mAh
Dimensions (h × w× d)
...
165 × 66 × 66 mm
Weight .....................................................143 g
Noise level ....................................... 72 dB(A)
The declared noise emission level of the
appliance is 72dB(A), which represents
alevel Aof acoustic power with respect
to areference acoustic power of 1pW.
- 10 - 01/2025
2025, .
INSTRUCTIONS AND INFORMATION
ON DISPOSAL OF USED PACKAGING
MATERIAL
Dispose of used packaging material
at the location designated by the
municipality for waste disposal.
DISPOSAL OF USED ELECTRICAL
AND ELECTRONIC EQUIPMENT
Used electrical andelectronic products
must not be added to ordinary
municipal waste. For proper disposal
and recycling of these products, deliver
them to designated collection points.
Alternatively, in some European Union
states or other European countries the
products can be returned to the local
retailer when buying an equivalent new
product. By properly disposing of this
product, you help preserve valuable
natural resources and contribute to
preventing potential negative impacts
on the environment and human health
resulting from improper waste disposal.
For more details, contact your local
authority or nearest collection point.
Fines may be imposed for improper
disposal of this type of waste as per
national regulations.
For Business Entities in European
Union States
To dispose of electric or electronic
equipment, request necessary
information from your retailer or supplier.
Disposal in Other Countries Outside the
European Union
If you wish to dispose of this product,
request the necessary information about
the correct disposal method from the
local council or from your retailer.
Changes to text and technical
parameters are reserved.
FAST ČR, a.s.
U Sanitasu 1621
CZ-251 01 Říčany
www.sencor.com
info@sencor.cz
