SST-ST55F-GS SST-ST65F-GS SST-ST75F-GS
STRIDER GOLD S SERIES
World’s smallest, full-modular ATX power supplies
Compact design with a depth of 140mm for easy integration
80 PLUS Gold certification
100% modular cables
24/7 continuous power output with 40℃ operating temperature
Class-leading single +12V rail
Strict ±3% voltage regulation and low ripple & noise
Silent running 120mm fan with 18dBA minimum
SPECIFICATION
SilverStone Strider Gold S
ST55F-GS
ST65F-GS
ST75F-GS
ATX12V / EPS 12V Switching Power Supply
With Active PFC
80 Plus Gold
PS/2
01
1.2 Inrush current regulation
1.1 AC input requirements
The input voltage, current, and frequency requirements for continuous operation are
stated below.
The power supply must meet inrush requirements for any rated AC voltage, during turn on at any
phase of AC voltage, during a single cycle AC dropout condition, during repetitive ON/OFF
cycling of AC,and over the specified temperature range (Top). The peak inrush current shall be
less than the ratingsof its critical components (including input fuse, bulk rectifiers, and surge
limiting device).
This specification describes the requirements 550W/650W/750W switching
power supply with an stretch ATX form-factor and EPS 12V, +5V standby voltage,
remote on/off control,full range line input capability and forced air cooling characteristics.
1.0 AC INPUT
Power factor correction (PF)>0.9 at full load.
Parameter Min Nom Max Unit
Vin 90 100 ---- 240 264 VACrms
Vin Frequency 47 60 ------- 50 63 Hz
Iin(550W) 8.0 ----- 4.0
Iin(650W) 9.0 ----- 4.5
Iin(750W) 10.0 ---- 5.0
02
2.1 DC voltage regulation
2.2 LOAD RANGE
2.0 DC OUTPUT
Parameter
+3.3V
+5V
+12V
–12V
+5Vsb
Range
±3%
±3%
±3%
±5%
±5%
Min
+3.14
+4.75
+11.4
-11.4
+4.75
Nom
+3.3
+5.0
+12.0
-12.0
+5.0
Max
+3.47
+5.25
+12.6
-12.6
+5.25
Unit
Volts
Volts
Volts
Volts
Volts
Parameter
+3.3V
+5V
+12V
-12V
+5VSb
Min
0
0
0
0
0
Nom.
-
-
-
-
-
Max
20
20
45
0.3
2.5
Peak Unit
Amps
Amps
Amps
Amps
Amps
2.2.1 550W Load range
2.2.2 650W Load range
Notes:
( 1 ) The maximum combined load on +3.3V and +5V outputs shall not exceed 100W.
( 2 ) The +12V maximum load shall not exceed 540W.
( 3 ) The maximum continuous average DC outputs power shall not exceed 550W.
( 4 ) Peak DC output power should not exceed 600W for 12 second.
Parameter
+3.3V
+5V
+12V
-12V
+5VSb
Min
0
0
0
0
0
Nom.
-
-
-
-
-
Max
20
20
54
0.3
2.5
Peak Unit
Amps
Amps
Amps
Amps
Amps
Notes:
( 1 ) The maximum combined load on +3.3V and +5V outputs shall not exceed 100W.
( 2 ) The +12V maximum load shall not exceed 648W.
( 3 ) The maximum continuous average DC outputs power shall not exceed 650W.
( 4 ) Peak DC output power should not exceed 700W for 12 second.
03
2.3 Output Ripple
2.3.1 Ripple regulation
2.3.3 Ripple voltage test circuit
2.3.2 Definition
2.2.3 750W Load range
Parameter
+3.3V
+5V
+12V
-12V
+5VSb
Min
0
0
0
0
0
Nom.
-
-
-
-
-
Max
20
20
62
0.3
2.5
Peak Unit
Amps
Amps
Amps
Amps
Amps
Parameter
+3.3V
+5V
+12V
-12V
+5VSb
Ripple&Noise
50
50
120
120
50
Unit
mVp-p
mVp-p
mVp-p
mVp-p
mVp-p
Notes:
( 1 ) The maximum combined load on +3.3V and +5V outputs shall not exceed 100W.
( 2 ) The +12V maximum load shall not exceed 744W.
( 3 ) The maximum continuous average DC outputs power shall not exceed 750W.
( 4 ) Peak DC output power should not exceed 800W for 12 second.
The ripple voltage of the outputs shall be measured at the pins of the output connector when
terminated in the load impedance specified in figure1.Ripple and noise are measured at the
connectors with a 0.1uF ceramic capacitor and a 10uF electrolytic capacitor to simulate system
loading. Ripple shall be measured under any condition of line voltage, output load, line frequency,
operation temperature.
AC Hot
AC Neutral
Power Supply
V out
V return
10uF 0.1uF
Load
Scope
AC Ground
04
Any overshoot at turn on or turn off shall be less 10% of the nominal voltage value, all outputs shall
be within the regulation limit of section 2.0 before issuing the power good signal of section 5.0.
2.4 Overshoot
2.5 Efficiency (at 115Vac)
In order to meet EuP* requirements the following guidance must be met for the +5Vsb efficiency
at 230V AC.
For example,for a rated +5 VDC output of 18A,the transient step would be 30% x 18A=5.4A
Output voltages should remin within the remain within the regulation limits of Section 2.1,and the
power supply should stable when subjected to load transients per Table 3. from any steady
state load,including any or all of the following conditions:
* Simultaneous load steps on the +12 VDC,+5 VDC,and +3.3 VDC outputs
(all steps occurring in the same direction)
* Load-changing repetition rate of 50 Hz to 10 kHz
* AC input range per Section 1.0
The power supply shall have current limit to prevent the +3.3 V, +5 V, and +12 V outputs from
exceeding the values shown in Table . If the current limits are exceeded the power supply shall
shutdown and latch off. The damaged from repeated power cycling in this condition. -12 V and 5
VSB shall be protected under over current or shorted conditions so that no damage can occur to
the power supply. All outputs shall be protected so that no damage occurs to the power supply
under a shorted output condition.
3.1 Over current protection
3.0 PROTECTION
load
20%
50%
100%
Efficiency
87
90
87
PF
>0.95
>0.95
Voltage
+12V(550W)
+12V(650W)
+12V(750W)
+5V
+3.3V
Over Current Limit (Iout limit)
47A minimum; 70A maximum
56A minimum; 80A maximum
65A minimum; 90A maximum
25A minimum; 45A maximum
25A minimum; 45A maximum
Output
+12 VDC
+5 VDC
+3.3 VDC
-12 VDC
+5 VSB
Maximum Step Size
(% of rated output amps)
40
%
30
%
30%
Maximum
Step Size (A)
0.1A
0.5A
05
3.2 Over Temperature Protection
The power supply will be protected against over temperature conditions caused by loss of fan
cooling or excessive ambient temperature.In an OTP condition the PSU will shutdown.When the
power supply temperature drops to within specifide limits,the power supply shall Lacth mode.
3.3 Over-power protection
The power supply will be shutdown and latch off when output power within 105~150% of rated
DC output.
Note: Assurance machine can work at low voltage,full load won't damage machine.
3.4 Under voltage protection.
In an under voltage fault occurs, the supply will latch all DC outputs into a shutdown state when
+12V,+5V & +3.3V outputs under 85% of it's maximum value.
3.5 Over voltage protection
The over voltage sense circuitry and reference shall reside in packages that are separate and
distinct from the regulator control circuity and reference.No single point fault shall be able to cause a
sustained over voltage condition on any or all outputs.The +5Vdc and +3.3Vdc and +12Vdc supply
shall provide
latch-mode over voltage protection and +5Vsb shall provide recover automatically as defined in Table.
3.6 Short circuit
3.7 No load operation
An output short circuit is defined as any output impedance of less than 0.1 ohms.The power supply
shall shut down and latch off for shorting the +3.3 VDC,+5 VDC,or+12VDC rails to return
or any other rail. Shorts between main output rails and +5VSB shall not cause any damage to the
power supply. The power supply shall either shut down and latch off or fold back for shorting the
negative rails.+5VSB must be capable of being shorted indefinitely,but when the short is removed,
the power supply shall recover automatically or by cycling PS_ON#.The power supply shall be
capable of withstanding a continuous short-circuit to the output without damage or overstress to
the unit
No damage or hazardous condition should occur with all the DC output connectors disconnected from
the load.The power supply may latch into the shutdown state.
Output
+12V VDC
+5 VDC
+3.3 VDC
+5Vsb DC
Minimum
13
5.5
3.6
5.5
Nominal
15
6
4
6
Maximum
17
7
5
7
Unit
Volts
Volts
Volts
Volts
06
Figure 2 is a reference for signal timing for main power connector signals and rails.
(1)T1: Power-on time (0.1~500ms)
(2)T2: Rise time (0.1~20ms)
(3)T3: Power good signal turn on delay time (100ms~500ms)
(4)T4: Power good signal turn off delay time (75%Load 1ms min)
(5)T5: Power good signal Rise time ( 20ms max)
(6)T6: Hold up time (75%Load 16ms Min)
Figure 2. PS-OK Timing Sequence
4.1 Signal timing drawing
When the power loss its input power, it shall maintain 16ms in regulation limit at normal input
voltage and 75% load (AC:115V/60Hz or 230V/50Hz)
4.2 Hold up time
5.1 Operation
5.2 Shipping and Storage
5.3 Altitude
4.0 TIMING
5.0 ENVIRONMENT
Temperature
0 to 40
o
C
Relative Humidit
y
to 85%,on-condensin
g
Temperature
-20 to 70
o
C
Relative Humidit
y
to 95%,non-condensin
g
O
p
eratin
g
2000m
Stora
g
e
3000m
07
6.1 Underwriters Laboratory (UL) recognition.
The power supply designed to meet UL 60950.
The demonstrated MTBF shall be 100,000 hours of continuous operation at 25oC, full load and
120V AC input. The MTBF of the power supply shall be calculated in accordance with
MIL-HDBK-217F. The DC FAN is not included.
7.1 ELECTROSTATIC DISCHARGE (ESD) – IEC 61000-4-2(EN 61000-4-2).
7.2 RADIATED SUSCEPTIBILTY – IEC 61000-4-3(EN 61000-4-3).
7.4 SURGE – IEC 61000-4-5(EN 61000-4-5).
7.5 CONDUCTED SUSCEPTIBILTY – IEC 61000-4-6(EN 61000-4-6).
7.6 POWER FREQUENCY MAGNETIC FIELD – IEC 61000-4-8(EN 61000-4-8).
7.7 VOLTAGE DIPS – IEC 61000-4-11(EN 61000-4-11).
7.8 VOLTAGE FLUCTUATIONS – IEC 61000-3-3 (EN 61000-3-3).
7.9 HARMONIC CURRENT EMISSION – IEC61000-3-2(EN 61000-3-2).
7.10 EN55032:Class B Radio interference (CISPR 22).
8.1 MTBF (mean time between failures) calculation
7.11 ANSI C63.4-2009 / FCC Part 15 Subpart B / ICES-003 lssue 5 Class B
115VAC operation.
7.3 ELECTRICAL FAST TRANSIENT / BURST ( EFT/B) – IEC 61000-4
-4(EN 61000-4-4).
9.1 Physical dimension : W150mm*H86mm*D140mm
6.0 SAFETY
7.0 ELECTROMAGNETIC COMPATIBILITY (EMC)
8.0 MTBF
9.0 MECHANICAL REQUIREMENTS
10.0 Power supply connector overuse definition
08
Power supply connector overuse definition
EN
Définition de l'utilisation excessive du
connecteur d'alimentation électrique
FR
A single PCIe 8pin cable and connector’s maximum current rating is
12.5A, which is 150W (+12V x 12.5A). So SilverStone’s warranty will not
cover damages or malfunction resulting from the use of a graphics card
or expansion card with a single PCIe 8pin connector that exceeds
standard 225W total power draw (150W from PCIe 8pin connector +
75W from PCIe motherboard slot). Similarly, a graphics card or
expansion card with dual PCIe 8pin connectors that exceed 375W total
power draw (300W from two PCIe 8pin connectors + 75W from PCIe
motherboard slot) will also not be covered under warranty.
Peripheral (molex) or SATA connector’s maximum current rating is 5A,
which is 60W (+12V x 5A) or 25W (+5V x 5A). Please ensure connected
devices are operating under these limits. SilverStone’s warranty will not
cover damages or malfunction resulting from usages exceeding these
connectors and their associated cables.
24pin motherboard connector’s maximum current rating for its dual
+12V metal pins are 5A each, which totals 120W (+12V x 5A x 2).
Please ensure +12V drawing devices connected to the motherboard are
operating under these limits. SilverStone’s warranty will not cover
damages or malfunction resulting from usages exceeding these
connectors and their associated cables.
La corrente massima di un singolo cavo PCIe a 8 pin e del connettore
è 12,5 A, corrispondente a 150 W (+12 V x 12,5 A). Pertanto, la
garanzia di SilverStone non copre danni o malfunzionamenti derivanti
dall'utilizzo di una scheda grafica o una scheda di espansione con un
singolo connettore PCIe a 8 pin che supera l'assorbimento totale di
225 W (150 W da connettore PCIe a 8 pin + 75 W da slot PCIe).
Analogamente, la garanzia non copre anche una scheda grafica o
una scheda di espansione con doppi connettori PCIe a 8 pin che
superano l'assorbimento totale di 375 W (300 W da doppi connettori
PCIe a 8 pin + 75 W dalla scheda madre PCIe).
La corrente massima del connettore periferico (molex) o SATA è 5 A,
corrispondente a 60 W (+12 V x 5 A) o 25 W (+5 V x 5 A). Assicurarsi
che i dispositivi collegati funzionino entro questi limiti. La garanzia di
SilverStone non copre danni o malfunzionamenti derivanti da uso
eccessivo di questi connettori e dei relativi cavi.
La corrente massima del connettore a 24 pin per scheda madre per i
suoi due pin di metallo a +12 V è di 5 A ciascuno, per un totale di 120
W (+12 V x 5 A x 2). Assicurarsi che i dispositivi a +12 V collegati alla
scheda madre funzionino con questi limiti. La garanzia di SilverStone
non copre danni o malfunzionamenti derivanti da uso eccessivo di
questi connettori e dei relativi cavi.
Definition einer Überlastung des
Netzanschlusses
DE
Die maximale Stromstärke eines einzelnen 8-poligen PCIe-Kabels und
Anschlusses beträgt 12,5 A, was 150 W (+12 V x 12,5 A) entspricht.
Daher deckt die SilverStone-Garantie keine Schäden oder
Fehlfunktionen durch den Einsatz einer Grafikkarte oder Erweiterungs-
karte mit einem einzigen 8-poligen PCIe-Anschluss ab, die die
Standardleistungsaufnahme von insgesamt 225 W übersteigt (150 W
vom 8-poligen PCIe-Anschluss + 75 W vom PCIe-Motherboard-
Steckplatz). Ebenso wird die Verwendung einer Grafikkarte oder
Erweiterungskarte mit zwei 8-poligen PCIe-Anschlüssen, die eine
Leistungsaufnahme von insgesamt 375 übersteigen (300 W von den
beiden 8-poligen PCIe-Anschlüssen + 75 W vom PCIe-Motherboard-
Steckplatz) nicht durch die Garantie abgedeckt.
Der maximale Nennstrom von Peripherie- (Molex) oder
SATA-Anschluss beträgt 5 A, was 60 W (+12 V x 5 A) oder 25 W (+5 V
x 5 A) entspricht. Bitte achten Sie darauf, dass verbundene Geräte
unter diesen Grenzwerten arbeiten. Die Garantie von SilverStone deckt
keine Schäden oder Fehlfunktionen aufgrund einer Nutzung ab, die
diese Anschlüsse und ihre zugehörigen Kabel übersteigt.
Der maximale Nennstrom des 24-poligen Motherboard-Anschlusses für
seine dualen +12-V-Metallkontakte beträgt jeweils 5 A, was insgesamt
120 W (+12 V x 5 A x 2) ergibt. Bitte stellen Sie sicher, dass mit dem
Motherboard verbundene +12-V-Geräte unter diesen Grenzwerten
arbeiten. SilverStones Garantie deckt keine Schäden oder
Fehlfunktionen aufgrund einer Nutzung jenseits der Angaben dieser
Anschlüsse und ihrer zugehörigen Kabel ab.
La corriente máxima de un solo cable PCIe de 8 pines es 12,5A, lo
que son 150W (+12V x 12,5A). Por tanto, la garantía de SilverStone
no cubrirá daños o fallos provocados por el uso de una tarjeta gráfica
o de expansión con un único conector PCIe de 8 pines que exceda el
total estándar de 225W (150W del conector PCIe de 8 pines + 75W
del zócalo PCIe de la placa base). De igual modo, una tarjeta gráfica
o de expansión con conectores duales PCIe de 8 pines que superen
375W de potencia (300W de los dos conectores PCIe de 8 pines +
75W del zócalo de la placa base) tampoco será cubierta por la
garantía.
La corriente máxima del conector de periféricos (molex) o SATA es
5A, que son 60W (+12V x 5A) o 25W (+5V x 5A). Por favor,
asegúrese de que los dispositivos conectados funcionan dentro de
estos límites. La garantía de SilverStone no cubrirá daños o fallos a
resultas de un uso excesivo de estos conectores y sus cables
asociados.
La corriente máxima del conector de 24 pines de la placa base para
sus pines de metal duales de +12V es de 5A cada uno, para un total
de 120W (+12V x 5A x 2). Por favor, asegúrese de que los
dispositivos de +12V conectados a la placa base funcionan dentro de
estos límites. La garantía de SilverStone no cubrirá daños o averías a
resultas de un uso excesivo para estos conectores y sus cables
asociados.
Le courant nominal maximum d'un périphérique (Molex) ou d'un
connecteur SATA est de 5 A, ce qui correspond à 60 W (+12 V x 5 A)
ou 25 W (+5 V x 5 A). Veuillez vous assurer que les appareils
connectés fonctionnent dans ces limites. La garantie de SilverStone
ne couvre pas les dommages ou les dysfonctionnements résultant
d'utilisations dépassant ces connecteurs et leurs câbles associés.
Le courant nominal maximal des connecteurs 24 broches de la carte
mère pour ses doubles broches métalliques +12 V est de 5 A chacun,
ce qui représente au total 120 W (+12 V x 5 A x 2). Veuillez vous
assurer que les dispositifs de tension +12 V connectés à la carte mère
fonctionnent dans ces limites. La garantie de SilverStone ne couvre
pas les dommages ou les dysfonctionnements résultant d'utilisations
dépassant la capacité de ces connecteurs et de leurs câbles
associés.
Le courant nominal maximum d'un câble et d'un connecteur PCIe 8
broches unique est de 12,5 A, ce qui correspond à 150 W (+12 V x
12,5 A). La garantie de SilverStone ne couvre donc pas les dommages
ou les dysfonctionnements résultant de l'utilisation d'une carte
graphique ou d'une carte d'extension avec un connecteur PCIe 8
broches unique qui dépasse une consommation énergétique totale de
225 W standard (150 W provenant du connecteur PCIe 8 broches + 75
W provenant de l'emplacement de la carte mère PCIe). De même, une
carte graphique ou une carte d'extension avec deux connecteurs PCIe
8 broches qui dépasse une consommation énergétique totale de 375 W
(300 W provenant des deux connecteurs PCIe 8 broches + 75 W
provenant de l'emplacement de la carte mère PCIe) ne sera également
pas couverte dans le cadre de la garantie.
Definizione di uso eccessivo del connettore
di alimentazione
IT
Definición de uso excesivo del conector de
la Fuente de alimentación
ES
09
Определение чрезмерной нагрузки на
коннектор блока питания
RU
전원 공급 커넥터 과용 정의
KR
Один кабель и коннектор PCIe 8pin поддерживает ток 12.5A, что
равно 150Вт (+12В x 12.5A). Таким образом, гарантийные
обязательства SilverStone не будут действовать если вы
используете видеокарту или другую карту расширения с одним
коннектором PCIe 8pin, которые превышает стандартную общую
потребляемую мощность 225Вт (150Вт через коннектор PCIe 8pin +
75Вт через слот PCIe материнской платы). Аналогично, видеокарта
или другая карта расширения с двумя коннекторами PCIe 8pin,
которые превышают общую потребляемую мощность 375Вт (300Вт
через коннектор PCIe 8pin + 75Вт через слот PCIe материнской
платы), также не будут покрываться гарантией.
Максимальный номинальный ток периферийного (molex) или SATA
разъёма составляет 5A, что равно 60Вт (+12В x 5A) или 25Вт (+5В x
5A). Пожалуйста, убедитесь, что подключенные устройства
работают в этих пределах. Гарантия SilverStone не будет
распространяться на неисправности, возникающие в результате
использования этих коннекторов или подключаемых к ним кабелей.
Максимальный номинальный ток 24pin коннектора материнской
платы для его двойных металлических контактов +12В составляет
5A на каждый, что равно 120Вт (+12В x 5A x 2). Пожалуйста,
убедитесь, что устройства, подключенные к линии +12В, работают
в этих пределах. Гарантия SilverStone не будет распространяться
на неисправности, возникающие в результате использования этих
коннекторов или подключаемых к ним кабелей.
单条PCIe 8pin电源线与接头的最大额定电流为12.5A，瓦特数150W
（+ 12V x 12.5A）。 因此，银欣的电源保固不包括用于单条PCIe
8pin接头之显卡/扩充卡，在超过标准225W总功耗范围所造成的损坏
或故障（150W 的PCIe 8pin接头+ 75W的主板PCIe插槽）。 以此类
推，若具备双PCIe 8pin接头的显卡/扩充卡，负载一但超过375W总
功耗，视同不属保固范围内（300W来自两个PCIe 8pin接头 + 75W的
主板PCIe插槽）。
大4pin（molex）或SATA接头的最大额定电流为5A，即60W（+ 12V x
5A）或25W（+ 5V x 5A）。 请确保连接的设备皆低于此限制下运行
。
银欣不保固超出电源供应器接头及其相关线材之使用负载上限所造
成的损坏或故障。
24pin主板接头的双+12V金属针脚最大额定电流为5A，即120W（+
12V x 5A x 2）。请确保连接的+12V设备皆低于此限制下运行。
银欣不保固超出电源供应器接头及其相关线材之使用负载上限所造
成的损坏或故障。
단일한 PCIe 8핀 케이블 및 커넥터의 최대 전류 정격은 12.5A로서
전력으로 환산하면 150W(+12V x 12.5A)입니다. SilverStone의
보증에서는 표준 225W의 총 소비 전력 (PCIe 8핀 커넥터의 150W와
PCIe 메인보드 슬롯의 75W의 합)을 초과하는 단일 PCIe 8핀 커넥터
탑재 그래픽 카드나 확장 카드를 사용하여 발생하는 손상 또는
오작동을 보상하지 않습니다. 이와 마찬가지로 375W의 총 소비
전력(PCIe 8핀 커넥터 2개의 300W와 PCIe 메인보드 슬롯의 75W의
합)을 초과하는 듀얼 PCIe 8핀 커넥터 탑재 그래픽 카드나 확장 카드를
사용해도 보증에서 보상해주지 않습니다.
주변장치(molex) 또는 SATA 커넥터의 최대 전류 정격은 5A로서
전력으로 환산하면 60W(+12V x 5A) 또는 25W(+5V x 5A)입니다.
연결된 장치들은 이러한 제한 하에서만 작동시켜야 합니다. SilverStone
의 보증에서는 이러한 커넥터 및 이와 연결되는 케이블의 정격을
초과하여 사용함으로써 발생하는 손상이나 오작동을 보상하지
않습니다.
듀얼 +12V 금속 핀에 사용되는 24핀 메인보드 커넥터의 정격 전류는
5A 이며, 각각 합계가 120W (+12V x 5A x 2) 입니다. 메인보드에
연결된 +12V 장치가 해당 한계 미만으로 작동되도록 하십시오.
SilverStone은 이 커넥터나 관련 케이블의 한계를 초과해서
사용함으로써 발생하는 손상이나 고장에 대해서 보장하지 않습니다.
電力供給コネクタの使用限度超過に関する説明
JP
単一のPCIe8ピンケーブルおよびコネクタの最大定格電流は12.5Aで
150W(+12Vx12.5A)となります。それで定格225W合計電力消費(PCIe8
ピンコネクタからの150W+PCIeマザーボードスロットからの75W)を超
える、単一PCIe8ピンコネクタ装備のグラフィックスカードまたは拡張カ
ード使用によって生じた損傷や故障の場合、SilverStoneの製品保証は適
用外となります。同様に、375W合計電力消費(2基のPCIe8ピンコネクタ
からの300W+PCIeマザーボードスロットからの75W)を超える、デュア
ルPCIe8ピンコネクタ装備のグラフィックスカードまたは拡張カード使用
によって生じた損傷や故障の場合も、製品保証適用外となります。
周辺用(molex)またはSATAコネクタの最大定格電流は5Aで、60W
(+12Vx5A)または25W(+5Vx5A)となります。接続された装置がこれら
限度以内で動作することを確認してください。これらコネクタおよび関連
ケーブルの定格を超える使用法で生じた損傷や故障については、
SilverStone製品保証対象外となりますのでご注意ください。
24ピンマザーボードコネクタのデュアル+12V金属製ピンに対する最大
定格電流はそれぞれ5Aなので合計は120W(+12Vx5Ax2)となります。
接続される+12V入力のデバイスが、これら上限以内で動作することをご
確認ください。これらコネクタおよび関連ケーブルでの限界を超えた使
用で生じた損傷または故障は、SilverStoneによる製品保証対象外となり
ます。
电源供应器接头过度使用定义
CN
電源供應器接頭過度使用定義
TW
單條PCIe 8pin電源線與接頭的最大額定電流為12.5A，瓦特數150W
（+ 12V x 12.5A）。 因此，銀欣的電源保固不包括用於單條PCIe
8pin接頭之顯卡/擴充卡，在超過標準225W總功耗範圍所造成的損壞
或故障（150W 的PCIe 8pin接頭+ 75W的主機板PCIe插槽）。 以此
類推，若具備雙PCIe 8pin接頭的顯卡/擴充卡，負載一但超過375W
總功耗，視同不屬保固範圍內（300W來自兩個PCIe 8pin接頭 + 75W
的主機板PCIe插槽）。
大4pin（molex）或SATA接頭的最大額定電流為5A，即60W（+ 12V x
5A）或25W（+ 5V x 5A）。 請確保連接的設備皆低於此限制下運行
。
銀欣不保固超出電源供應器接頭及其相關線材之使用負載上限所造
成的損壞或故障。
24pin主機板接頭的雙+12V金屬針腳最大額定電流為5A，即120W（+
12V x 5A x 2）。請確保連接的+12V設備皆低於此限制下運行。
銀欣不保固超出電源供應器接頭及其相關線材之使用負載上限所造
成的損壞或故障。
10
ขีดจำกัดการรองรับการใช้งานของขั้วต่อจากพาวเวอร์ซัพพลาย
TH
Please refer to SilverStone website for latest specifications updates.
สำหรับขั้วเชื่อมต่อและสายไฟเลี้ยง PCIe 8 พินสามารถรองรับกระแสได้สูงสุด 12.5
แอมป์หรือหมายถึง 150 วัตต์
(+12V x 12.5A) ดังนั้นการรับประกันจากทาง SilverStone
จะไม่ครอบคลุมถึงความเสียหายหรือความผิดปรกติซึ่งเกิดขึ้นกับกราฟิกการ์ดรวมถึงการ์
ดขยายความยาวที่ใช้งานขั้วเชื่อมต่อ PCIe 8 พิน
ซึ่งมันมีการใช้พลังงานรวมทั้งสิ้นเกินกว่ามาตรฐานที่กำหนดคือ 225 วัตต์ (150
วัตต์ จาก PCIe 8 พิน + 75 วัตต์ จากสล๊อต PCIe บนเมนบอร์ด)
อันรวมถึงกราฟิการ์ดหรือการ์ดขยายความยาวที่ใช้ขั้วต่อไฟเลี้ยง PCIe 8 พินจำนวน 2
ชุดซึ่งมีการใช้พลังงานทั้งสิ้น 375 วัตต์ (300 วัตต์ จากขั้ว PCIe 8 พิน 2 ชุด +
75 วัตต์ จากสล๊อต PCIe บนเมนบอร์ด) ซึ่งไม่ครอบคลุมเช่นกัน
ภายใต้การรับประกัน ขั้วเชื่อมต่อ Peripheral หรือ Molex 4 พินและ SATA
มันสามารถรองรับกระแสได้สูงสุด 5 แอมป์หรือหมายถึง 60 วัตต์ (+12V x 5A)
หรือ (+5V + 5A)
กรุณาให้แน่ใจว่าอุปกรณ์ที่ใช้งานมีการใช้พลังงานไม่เกินกว่าขีดจำกัดที่รองรับ
ดังนั้นการรับประกันจากทาง SilverStone
จะไม่ครอบคลุมถึงความเสียหายหรือความผิดปรกติจากอุปกรณ์ที่เชื่อมต่อใช้งานจากตัวส
ายเชื่อมต่อซึ่งมีการใช้พลังงานเกินกว่าขีดจำกัด
กระแสไฟฟ้าสูงสุดของขั้วต่อเมนบอร์ด 24 พิน สำหรับพินโลหะ +12V คู่แต่ละอันมีค่า
5A ซึ่งรวมทั้งหมดเป็น 120W
(+12V x 5A x 2) โปรดตรวจสอบให้มั่นใจว่าอุปกรณ์ตัวดึงพลังงาน +12V
ที่เชื่อมต่อกับเมนบอร์ดสามารถทำงานภายใต้ขีดจำกัดเหล่านี้ได้ การรับประกันของ
SilverStone ไม่คุ้มครองความเสียหาย
หรืออาการเสียที่เป็นผลจากการใช้เกินขีดจำกัดของขั้วต่อและสายเคเบิลที่ใช้เชื่อมต่อเหล่านี้
1. 為了保護使用者及防火的目的，安裝此交換式電源供應器時，必須安裝於符合下列各項要求的外殼中，
並且安裝妥善後，才可接上電源。
1-1. 外殼材質須為防火外殼。外壳材质须为防火外壳。
1-2. 外殼的上方及側邊之圓形開孔，最大內徑不可大於5mm。
1-3. 外殼的上方及側邊之長條型開孔，對角線距離不可大於5mm；若寬度小於1mm，則長度不受限制。
1-4. 外殼底部不可有開孔。外壳底部不可有开孔。
直徑不大於5mm
對角線不大於5mm
寬度小於1mm 則長度不限
Openings that do not exceed 1mm in width regardless of length
Openings that do not exceed 5mm in any dimension
2. 本產品輸出含有危險能量，為避免操作時發生危險，須於裝入系統機殼並將所有設備安裝妥當後才可開啟電源。
3. 本產品之電源輸出非屬電力限制型電源，請連接使用具防火外殼之周邊，以避免火災危險發生。
BSMI ROHS 資訊
http://www.silverstonetek.com/downloads/PSU/RSD.pdf
NO. G11234290
