Read all instructions before
assembling and using product.
IMPORTANT - Keep instructions for
future use.
0222R1-600
Owner’s Manual
UNIVERSAL THREE DRAWERS
DRESSER
Scan the QR code to register your product
https://dreamonme.com/customercare/registration/
2
www.dreamonme.com/help
SAFETY TIPS
Adult Assembly
Required.
DO NOT use the
product if it is
damaged, broken,
and/or components are
missing or broken.
To protect your parts
during assembly,
please place them on a
soft surface.
Small parts may
present choking
hazard prior to
assembly.
Please read the
instructions
thoroughly. Identify all
parts & hardware.
Improper or unsafe use
of power drills/drivers
can result in death or
serious injury.
To clean surface, use
only water on a damp
cloth. Do not use
window cleaner or
cleaning abrasive as it
will scratch the surface
and could damage the
protective coating.
0-6
Always monitor your
child’s activity in the
nursery or near
furniture.
Contact Dream On
Me in case of any
assistance needed.
…. for choosing Dream On Me and congratulations on joining our family;
a family that has been transforming lives for over 30 years!
We appreciate your feedback and wish you the very best in the
coming years with your new addition. If you have any questions
or concerns please don’t hesitate to reach out to us. One of our
trusted Customer Care representatives will be happy to assist you.
Thank you again for entrusting us to provide you with safe
and affordable baby products and accessories.
THANK YOU...
LIMITED WARRANTY:
• Dream On Me warrants its product to be free from defects in material and
workmanship and agrees to remedy any such defect.
• This warranty covers 1 year from the date of original purchase.
• This warranty is valid only upon presentation of proof of purchase.
• This is solely limited to the repair or replacement of defective furniture
components and no assembly labor is included.
• This warranty does not apply to any product which has been improperly
assembled, subjected to misuse or abuse or which has been altered or
repaired in any way.
• This warranty gives you specific legal rights and you may also have other
rights which vary from State to State.
www.dreamonme.com/help
3
WARNINGS
www.dreamonme.com/help
4
• FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY INSTRUCTIONS COULD
RESULT IN SERIOUS INJURY OR DEATH.
• CHECK THIS PRODUCT FOR DAMAGED HARDWARE, LOOSE JOINTS, MISSING PARTS
OR SHARP EDGES BEFORE AND AFTER ASSEMBLY AND FREQUENTLY DURING USE.
• DO NOT USE THIS DRESSER IF ANY PARTS ARE MISSING, DAMAGED OR BROKEN.
CONTACT DREAM ON ME - 1532 S. WASHINGTON AVE, PISCATAWAY, NJ 08854 FOR
REPLACEMENT PARTS.
• IF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR CHILDREN’S PRODUCTS.
• SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM FURNITURE TIP-OVER.
TO HELP PREVENT THIS, PLACE THE HEAVIEST ITEMS ON THE LOWER SHELVES AND
DRAWERS. DO NOT SET HEAVY OBJECTS ON TOP SHELVES AND DRAWERS.
• NEVER OPEN MORE THAN ONE DRAWER AT A TIME.
• THE USE OF TIP-OVER RESTRAINTS MAY REDUCE BUT NOT ELIMINATE THE RISK OF
TIP-OVER.
• DO NOT SET TVs OR OTHER HEAVY OBJECTS ON TOP OF THIS PRODUCT.
• ALWAYS MONITOR YOUR CHILD’S ACTIVITY WHEN IN THE NURSERY.
• NEVER ALLOW CHILDREN TO CLIMB OR HANG ON DRAWERS, SHELVES, AND DOORS.
• DO NOT ALLOW CHILDREN STANDING IN DRAWERS.
• DO NOT ALLOW CHILDREN STANDING ON TOP OF THIS PRODUCT.
• TO AVOID HEAD INJURY, DO NOT ALLOW CHILDREN TO PLAY UNDERNEATH OPEN
DRAWERS.
• DO NOT LEAVE DRAWERS OPEN WHEN IN USE.
• ACCESSORY ITEMS MUST BE SECURELY FASTENED TO THIS PRODUCT ACCORDING
TO THE INSTRUCTIONS PROVIDED WITH THOSE ITEMS.
CHILDREN HAVE DIED FROM FURNITURE TIPOVER, TO REDUCE THE RISK OF
TIPOVER :
• ALWAYS INSTALL TIPOVER RESTRAINT PROVIDED.
• NEVER PUT A TV ON THIS PRODUCT.
• NEVER ALLOW CHILDREN TO STAND, CLIMB OR HANG ON DRAWERS, DOORS OR
SHELVES.
• NEVER OPEN MORE THAN ONE DRAWER AT A TIME.
• PLACE HEAVIEST ITEMS IN THE LOWER DRAWERS.
www.dreamonme.com/help
5
PARTS
If there are any missing parts, please contact Dream On Me before using the
product.
Dresser Top Panel
1
Dresser Left
Side Panel
2
Dresser Right
Side Panel
3
Dresser Rear
Top Panel
4
Dresser Rear
Bottom Panel
5
Dresser Top
Front Rail
6
Dresser Center
Front Rail (x2)
7
Dresser Bottom
Front Rail
8
Drawer Front
Panel (x3)
9
Drawer Left
Panel (x3)
10
Drawer Rear
Panel (x3)
13
Drawer Support
Rail (x3)
14
Drawer Base
Panel (x3)
11
Drawer Right
Panel (x3)
12
www.dreamonme.com/help
6
HARDWARE
If there are any missing parts, please contact Dream On Me before using the
product.
8
6
Bolt 1-3/4” (×14)
A
Bolt 1” (×10)
B
Wooden Dowel
1-3/8” (×4)
C
Curve Washer (×14)
D
Screw 1” (×27)
E
Wooden Dowel
3/4” (×12)
F
Handle (×63)
G
Screw 3/4” (×6)
H
Allen Key (x1)
I
Bracket (x4)
J
Straps (x2)
K
Screw 1-1/2” (x4)
L
Screw 3/4” (x4)
M
Tools Needed:
Philips Screw Driver
(NOT INCLUDED)
Power drill - 3/32" drill bit
(NOT INCLUDED)
www.dreamonme.com/help
7
Bolt 1-3/4” (×6)
A
Bolt 1” (×2)
B
Curve Washer (×6)
D
(2)
(2)
(5)
(4)
(5)
(6)
(7)
(7)
(8)
(B)
(B)
(A)
(D)
(A,D)
1
DRESSER ASSEMBLY - DRESSER FRAME ASSEMBLY
1a. Place the Dresser Left Side Panel
(2) on a soft surface, align the
Dresser Rear Top Panel (4) and
Dresser Rear Bottom Panel (5) as
shown in the diagram.
1b. Insert the Curve Washer (D) into
the Bolt (A) and use the same to
attach the Rear Top Panel (4) and
Rear Bottom Panel (5). Ensure not
to overtighten the bolts.
1c. Similarly, use the Curve Washer (D)
and the Bolt (A) assembly to attach
the Dresser Top Front Rail (6) and
Dresser Bottom Front Rail (8) to the
Dresser Left Side Panel (2).
1d. Attach both Dresser Center Front
Rails (7) using Bolts (B) to the
insertions at the center of the
Dresser Left Side Panel (2).
www.dreamonme.com/help
8
Bolt 1-3/4” (×6)
A
Bolt 1” (×2)
B
Curve Washer
(×6)
D
(3)
(B)
(B)
(A,D)
2
DRESSER ASSEMBLY - DRESSER FRAME ASSEMBLY
2a. Align the Dresser Right Side Panel
(3) on the above assembly made.
2b. Use the Curve Washer (D) and the
Bolt (A) assembly to attach the
Rear Top Panel (4) and Rear
Bottom Panel (5).
2c. Similarly, use the Curve Washer (D)
and the Bolt (A) assembly to attach
the Dresser Top Front Rail (6) and
Dresser Bottom Front Rail (8) to
the Dresser Right Side Panel (3).
2d. Attach both Dresser Center Front
Rails (7) using Bolts (B) to the
insertions at the center of the
Dresser Right Side Panel (3).
www.dreamonme.com/help
9
(1)
(C)
(B)
Bolt 1-3/4” (×2)
A
Bolt 1” (×6)
B
Wooden Dowel
1-3/8” (×4)
C
Curve Washer
(×2)
D
3
DRESSER ASSEMBLY - DRESSER FRAME ASSEMBLY
3a. Align the Dresser Top Panel (1)
as shown in the illustration.
Insert Wooden Dowels (C) at four
corners.
3b. Use the Curve Washer (D) and
the Bolt (A) assembly to attach
the Rear Top Panel (4).
3c. Insert the Bolts (B) from below,
to attach the Dresser Top Panel
(1) and the frame assembly
made as shown in the
illustration.
www.dreamonme.com/help
10
4
DRESSER ASSEMBLY - DRAWER ASSEMBLY
4a. Place one of the Drawer Front
Panels (9) on a soft surface, align
one of the Drawer Left Panels (10)
and one of the Drawer Right
Panels (12) as depicted in the
illustration.
4b. Attach the assembly using Screws
(E) on all four corners.
4c. Insert Wooden Dowels (F) below
one of the Drawer Support Rails
(14), attach the same to the
Drawer Front Panel (9).
4d. Slide one of the Drawer Base
Panels (11) into the grooves
present on the Right and Left Side
Panels. Ensure that the alignment
of the Base Panel is right.
(9)
(10)
(11)
(11)
(12)
(E)
(E)
(14)
(14)
(F)
(F)
6
Screw 1” (×4)
E
Wooden Dowel
3/4” (×2)
F
www.dreamonme.com/help
11
Handle (×1)
G
Screw 3/4” (×2)
H
(13)
(E)
(E)
(E)
(E)
(E)
(G)
(H)
(H)
6
Screw 1” (×5)
E
Wooden Dowel
3/4” (×2)
F
(F)
(F)
5
DRESSER ASSEMBLY - DRAWER ASSEMBLY
5a. Insert the Wooden Dowels (F) into
the insertions present on top of
the Drawer Support Rail (14),
align the Drawer Rear Panel (13)
on the above assembly made as
shown in the diagram.
5b. Attach the Drawer Rear Panel (13)
and the assembly using the Bolts
(E) at the center and four corners.
5c. Align the Handle (G), insert the
Screws (H) from behind the Front
Panel, pass it through the handle
(G) and tighten the same to
attach them.
5d. Follow the same steps to
assemble other drawers.
www.dreamonme.com/help
12
6
DRESSER ASSEMBLY - DRAWER ASSEMBLY
6a. Insert the assembled drawers
into the grooves present on the
dresser frame.
6b. Ensure the right alignment of
drawers before inserting them
into the frame.
www.dreamonme.com/help
13
NOTE:
Model shown is example only,
Styles may vary
7a. Determine the desired location of the
dresser. Find a wall stud behind the
furniture piece and position one of
the Brackets (J) vertically on the stud
approximately 1" below the top of
the dresser piece. Mark and drill a
pilot hole in the center of the stud
with a 3/32" drill bit. Attach the
Bracket (J) to stud with the two
Screws (L).
7b. The second bracket will need to be
attached horizontally to the top of
the dresser frame. Temporarily move
the dresser away from the wall and
place a bracket near the top of the
frame. Mark and drill holes for
screws with a 3/32" drill bit. Attach
the bracket to the dresser piece with
the two Screws (M).
7c. Move the dresser piece into its final
position, taking care to line up the
wall bracket with the dresser
bracket. Thread the strap through
the brackets as shown in the
illustrations. Tighten the strap until
snug. Note: Do not overtighten.
Similarly, follow the steps for the
other side of the furniture.
7
ANTI-TIP SAFETY HARDWARE INSTALLATION
WALL
WALL
WALL
WALL
WALL
FURNITURE
FURNITURE
FURNITURE
FURNITURE
(L)
(M)
(J)
(K)
(K)
FURNITURE
WALL
“Pull Down To Tighten”
“Insert”
“Insert”
1 2 3
www.dreamonme.com/help
14
FURNITURE CARE INSTRUCTIONS
ROOM CLIMATE CONTROL:
• Wood, when first cut contains more than 50 percent water. When it is prepared for
furniture construction it is placed in a Kiln and the moisture content is brought down
to 8 to 10 percent. Wood is porous and responds to its environment. If the room has
high humidity it will absorb it and expand and if the humidity is low it will lose
moisture and shrink.
• It is important that the humidity levels in the room be controlled from extremes of
too much humidity or too little. Furniture should not be placed close to the
air-conditioning outlets, fire places, radiators, space heaters, humidifiers or
dehumidifiers. Exposure to extreme variations of temperature and humidity can
damage any fine wood product.
THE IDEAL ENVIRONMENT FOR FINE FURNITURE:
• Fine wood furniture will have fewer problems when its environment is controlled at a
temperature between 65 and 75 degrees and a relative humidity between 35 and 40
percent. Wood placed in an environment outside of those limits can and will shrink
or expand and may develop some small cracks which are not material or structural
defects.
STICKING DOORS AND DRAWERS:
• With the minor changes in temperature and humidity, doors and drawers may swell
and be difficult to open or close. Tolerances have been built into the units but
extreme conditions may still cause sticking. This will adjust back to normal over
time but until it does consider using a dehumidifier or rub candle wax or paraffin on
sides that stick.
AVOID DIRECT SUNLIGHT:
• Keep the furniture out of direct sunlight. Ultraviolet rays will fade colors and in some
cases darken them. It can also cause crazing or hair line cracks in the finish. White
finishes will yellow naturally over time and exposure to direct sunlight will hasten
this natural process along with some woods darkening naturally over time; this is
not considered to be a quality defect.
PROPER STORAGE:
• If you need to put your furniture in storage for any period of time do not store them
in a damp basement or hot dry attic. Allow air movement around the furniture and
do not stack anything on it.
www.dreamonme.com/help
15
FURNITURE CARE INSTRUCTIONS (cont.)
IN GENERAL:
• Protect furniture surface from hot or extremely cold items.
• Use coasters under hot or cold beverages.
• Do not use synthetic fabric under accessories or lamps.
• Protect tops from pens, markers and crayons.
• Oils from potpourri and other scented items can damage the finish of the furniture.
• Do not drag items across the surface of the furniture.
• Allow the surface to breath by rotating your accessories and lamps.
• Do not over polish the furniture, do it only two or three times a year. Over polishing
can distort the natural finish of the product.
• Do not wax the furniture, as wax build up can destroy natural finish of the product.
• When moving furniture always lift the unit. Do not push or drag it to avoid damage
to legs.
• Keep the furniture level so doors and drawers open and close freely.
• Clean with a damp, not wet, cloth. Use only a mild soap. Do not use the abrasive
cleaners.
• Do not scratch or chip the finish.
• Inspect the product periodically, contact Dream On Me Inc for replacement parts
or questions.
• Do not store the product or any parts in extreme temperatures and conditions such
as a hot attic or a damp, cold basement. These extremes can cause a loss of
structural integrity.
• To preserve the luster of the high-quality finish on your product, it is recommended
to place a doily or felt pad under any items you place on the finish.
• Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty
of this fine finish.
• Do not use abrasive chemicals.
• Do not spray cleaners directly onto furniture.
• Lift slightly when moving on carpeting to prevent leg breakage.
• Use of a vaporizer near furniture will cause wood to swell and to peel.
YOU DID IT!
Congratulations Mom & Dad!
It's time to create your dream nursery. A safe, elegant
handcrafted dresser that meets all your storage needs.
1532 S. WASHINGTON AVENUE
PISCATAWAY, NJ 08854
www.dreamonme.com
Follow Us @dreamonmeinc
to get your nursery featured on our social media.
Enter our monthly giveaway!
Scan the QR code to register.
Chat with us!
Scan the QR code to Live Chat.
