Emergency start power supply & air pump
User Manual
1. Product Overview
2. Packing list
1.1 Product description
1.2 Function display area
1.3 Display and key
2.1 Standard configuration
4. Usage method
4.1 Aeration guide
4.2 Jump-Starter guide
4.3 Charge and discharge
4.4 Lighting operation
3. Type parameter
6. Safety statement
7. Disclaimer
6.1 Matters needing attention
6.2 Product care Tips
5. Troubleshooting guide
01
03
01
01
02
03
05
05
07
09
09
04
11
13
11
13
09
catalogue
1. Display
2. Lighting
3. Switch
4. Air pressure +
5. Unit adjustment
6. Air pressure -
7.Type-C input port
8. USB output
1.1 Product description
1.2 Functional area display
This product is a car jump starter with air compressor
multi-functional machine. It can give the car that can not start
due to battery loss for emergency ignition, and pump for car
tires. With USB output, it can charge mobile phones, tablet
computers and other devices, while having emergency lighting
function.
1. Product Overview
01
9
10
11
7
8
1
2
3
5
6
4
9.LED lights
10.EC5 interface
11. Inflation hose jack
Press and hold the Switch button for 2 seconds to
power on
Press and hold the "Switch" button for 2S to shut
down the machine. In non-working state, the
machine will shut down automatically for 1 minute
In the startup state, long press the "Unit adjustment"
key to switch between the four units of "PSI, BAR,
KPA, KG/CM2"
In the startup state, click the "Unit Adjustment"
button to switch between the five modes: Cars,
Motorcycles,Bicycles,Basketball,Pressure protection
In the startup state, press + or - to set the target
pressure value, or hold down to set the pressure
value in quick succession
In the startup state, press the light button, LED
lighting. Press the button the second time, the red
and blue lights flashing. Press button the third time,
the red light flash. Click again to turn off the light.
Function of button
1.3 Display and button
Inflation mode
Aeration unit
Electric quantity
02
03
Inflatable electric
all-in-one machine×1
Packing box×1
User Manual x1
EVA storage bagx1
User Manual
USB
Charging cable×1
2.1 Standard configuration
2. Packing list
Ball needle
×1
Rubber boat
conversion head×1
Swim ring
changeover head×1
Inflation hose×1
Smart battery clip×1
Presta
valve x1
Product model
Enter Type-C
Output USB-A
Charging time
Product size
Operating temperature
Battery type
Shell material
Standby power consumption
enforce standards
QS003
5V 2A
5V 2.4A
4-5h
190*95*75 mm
-20°C~60℃
Polymer battery
PC\ABS
<50μA
Q/BWKJ001-2023
The above data comes from laboratory measurements, but the
data may be different or inaccurate due to changes in the objective
environment.
3. Type parameter
04
4.1 Aeration guide
Step 1: Screw on the inflation hose
Step 2: Clamp the tire nozzle
Step 3: Long press the key to start, at this time, the product
screen will automatically display the current tire pressure value
05
4. Usage method
Step 4: Select and press the mode key to switch to
car mode. The default tire pressure of car mode is
2.5Bar. You can choose to press “+”or“-” to adjust
the appropriate air pressure value
Tips: During the inflation process, the tire pressure value
is displayed in real time, and it will automatically stop
when it is full.
Step 5: Automatically stop when the air pressure reaches the
preset value, or press the switch key again to stop the inflation,
and remove the air pipe from the car tire and fuselage after the
air pipe has cooled
06
Tips:The machine in the inflatable mode will automatically stop
working after using 10 minutes, and the screen shown “8.88”
flashing for at least 2 minutes for cooling down purpose. After the
screen restores to original state, the machine could start working
again.
07
4.2 Jump-Starter guide
Step 1: Press the power button to power on, check the power,
and ensure that the power is sufficient (more than 75% is
recommended)
Step 2: Insert Battery clip into the EC5 interface of the product.
At this time, the traffic light of the battery clip flashes,
indicating the normal operation of the product
Step 3: The red clip fully clamp the positive electrode of the
battery, the black clip fully clamp the negative electrode of the
battery, (or the black clip clip on the vehicle metal sheet). At this
point, the red and green flashing of the battery holder becomes
green and steady
Step 4: Start the car and close the door and all electronic
devices. Tip: Automatic, step on the brake and start. Manual
transmission, need to step on the clutch and brake at the same
time, and then start)
Step 5: After the vehicle starts, please remove the product
within 30 seconds. (Tip: First unplug, then remove the positive
and negative terminals of the battery clip)
Tip: If the power is not successful, follow the fifth step, remove
the battery clip, one minute later, re-operation. Do not start
continuously, the start time should not exceed five seconds.
08
09
We have summarized the suspected faults and common
problems that may be encountered when the equipment is
used, as follows
5. Troubleshooting guide
Charge the product
In the startup state, press the light button, LED lighting. Press the
button the second time, the red and blue lights flashing. Press
button the third time, the red light flash. Click again to turn off the
light.
4.4 Lighting operation
Connect the USB charging cable to
the charging head and connect to
the air pump for charging
Charge mobile phones, PSP, tablets and
other digital products
Press the power button to power on, and then connect the USB
charging cable to the USB output, you can charge mobile
phones, PSP, tablet computers and other digital products
4.3 Charge and discharge
The default setting value of pressure holding mode is 8PSI. The
adjustable range is: 5~150PSI. When the low pressure is below the
set value of 5PSI, the inflation will automatically start.
4.5 Pressure holding operation
Unable
to boot
Low battery
Please charge it
Product collision power off
protection
Charge activation
Hold down the power button
for about 3 seconds
Plug the power adapter fully
into the home outlet
Please charge for 3-5 hours
Clamp the battery clamp as
much as possible with the
battery large area, the contact
surface of the battery positive
and negative poles is clean,
and the indicator light is
normal
Turn off the electrical
appliances in the car and close
the doors when the power is
on
No battery lap or negative
electrode lap
Contact customer service
Please charge it
Set the corresponding device
mode correctly
Press the power button
The charging state fails to turn
on. Remove the charging cable
Charging
The charging cable is not
fully inserted into the
charging port
The adapter is not fully
plugged into the home
socket
Low battery
The battery clip is not
connected properly, and
the battery clip does not
recognize the battery
The electric appliances and
doors in the car are not
closed
Battery problem
Operational problem
Low battery
Wrong tire pressure pattern
Properly connect the gas pipe
and buckle
The buckle of the air pipe
is loose
Unable
to charge
Failure
to connect
Unable
to inflate
on startup
Insert the charging cable fully i
nto the charging port, and
make sure that the charging
port is not loose
Condition Possible cause The way to troubleshoot
10
Before use, please read the product instructions carefully to
avoid improper use of the product, which may easily cause
the product itself or may endanger the safety of life and
property
Please check the power of the machine before use, in order
to achieve better use, please ensure that the power is above
75%, charging is recommended to use the special charging
cable attached to the product
Make sure the EC5 plug (smart ignition clip) is fully plugged
into the boot power port. Otherwise, the startup
performance will be affected, and the plastic part of the
interface will have a negative impact, and may even melt
Do not use the emergency starting power to continuously
start the car at high frequency, and the time interval
between two ignitions must be greater than 30 seconds.
After connecting the intelligent ignition clip and the
emergency starting power, please start the car immediately
If the car does not start, check whether the smart ignition
clip is not securely connected, or check the surface of the
battery connector for rust or dirt, and then start the car after
the surface is clean. If it doesn't start after three consecutive
attempts, stop forcing your car to start, or it will damage the
product
Do not store this product in high temperature and
humidity, strong light and strong magnetic field
environment, do not place in the fire source and other
harsh environ-ment, such as due to the improper use of
consumers in violation of product instructions,
①
②
③
④
⑤
⑥
6. Safety statement
6.1 Matters needing attention
11
resulting in personal and property damage will bear all
consequences, the company will not assume any legal
responsibility, non-professional personnel are strictly
prohibited to disassemble this product
Avoid using electrical appliances or loads that exceed the
output current of this product (if forced use will trigger
circuit protection, the product has no output)
Avoid strong physical effects, including knocking, throwing,
trampling, squeezing, etc
This product is not a toy, it is prohibited for children to use,
the user is recommended to be over 16 years old, please
keep children and the product at a safe distance during the
inflating process
In order to extend the service life of the product, if the
product is not used for a long time, it is recommended to
charge it at least once every three months
Please use in a dry and clean environment, sand and dust
intrusion may cause damage to the product, the product is
not waterproof, do not wash with water
High pressure gas will generate heat during aeration, never
insert the trachea into the mouth, ear or eye of a person or
animal to prevent injury.
In order to ensure the good work of this product, after each
10 minutes of inflation, the machine must stop running for
5 minutes, cool down before use, in order to extend the life.
If there is abnormal noise in the inflation or the tempera-
ture is too high, please shut down immediately and allow it
to cool for at least 15 minutes, and be careful when
disassembling the gas pipe
Before use, please read the product instructions carefully to
avoid improper use of the product, which may easily cause
the product itself or may endanger the safety of life and
property
Please check the power of the machine before use, in order
to achieve better use, please ensure that the power is above
75%, charging is recommended to use the special charging
cable attached to the product
Make sure the EC5 plug (smart ignition clip) is fully plugged
into the boot power port. Otherwise, the startup
performance will be affected, and the plastic part of the
interface will have a negative impact, and may even melt
Do not use the emergency starting power to continuously
start the car at high frequency, and the time interval
between two ignitions must be greater than 30 seconds.
After connecting the intelligent ignition clip and the
emergency starting power, please start the car immediately
If the car does not start, check whether the smart ignition
clip is not securely connected, or check the surface of the
battery connector for rust or dirt, and then start the car after
the surface is clean. If it doesn't start after three consecutive
attempts, stop forcing your car to start, or it will damage the
product
Do not store this product in high temperature and
humidity, strong light and strong magnetic field
environment, do not place in the fire source and other
harsh environ-ment, such as due to the improper use of
consumers in violation of product instructions,
⑦
⑨
resulting in personal and property damage will bear all
consequences, the company will not assume any legal
responsibility, non-professional personnel are strictly
prohibited to disassemble this product
Avoid using electrical appliances or loads that exceed the
output current of this product (if forced use will trigger
circuit protection, the product has no output)
Avoid strong physical effects, including knocking, throwing,
trampling, squeezing, etc
This product is not a toy, it is prohibited for children to use,
the user is recommended to be over 16 years old, please
keep children and the product at a safe distance during the
inflating process
In order to extend the service life of the product, if the
product is not used for a long time, it is recommended to
charge it at least once every three months
Please use in a dry and clean environment, sand and dust
intrusion may cause damage to the product, the product is
not waterproof, do not wash with water
High pressure gas will generate heat during aeration, never
insert the trachea into the mouth, ear or eye of a person or
animal to prevent injury.
In order to ensure the good work of this product, after each
10 minutes of inflation, the machine must stop running for
8 minutes, cool down before use, in order to extend the life.
If there is abnormal noise in the inflation or the tempera-
ture is too high, please shut down immediately and allow it
to cool for at least 15 minutes, and be careful when
disassembling the gas pipe
⑩
⑪
⑫
⑬
12
⑧
13
①
②
③
④
6.2 Product care Tips
Keep the instrument dry and do not place it in high
temperature or humid environment
Product built-in lithium battery, the battery is prohibited to
use after immersion
If you do not use the product for a long time, please charge
and discharge it every 3 months
Do not disassemble, impact, squeeze or put into the fire
The illustrations of the products and accessories in the
instruction manual are for illustration reference. There may be
slight differences with the actual products. Please refer to the
actual products. We may make necessary changes to
typographical errors and inaccuracies in this manual at any
time without prior notice, but such changes will be incorporat-
ed into the new version of this manual.
7. Disclaimer
