ST75F-PT / ST65F-PT / ST55F-PT
STRIDER PLATINUM SERIES
World’s smallest 80 PLUS Platinum,
full-modular ATX power supplies
Compact design with a depth of 140mm for easy integration
High efficiency with 80 PLUS Platinum certification
100% modular cables
24/7 continuous power output with 40C operating temperature
Class-leading single +12V rail
Strict ±3% voltage regulation and low ripple & noise
Ultra silent 120mm fan with intelligent semi-fanless operation
o
SPECIFICATION
SilverStone Strider Platinum
SST-ST75F-PT
SST-ST65F-PT
SST-ST55F-PT
ATX12V / EPS 12V Switching Power Supply
With Active PFC
80Plus Platinum
PS/2
01
1.1 Scope
This specification defines the performance characteristics of a single phase 750, 650, 550 watts, 5 output
power supply. This specification also defines worldwide safety and electromagnetic compatibility
requirements for the power supply which is intended for use in computer products.
Nominal Voltage
100-240 Vrms
Voltage Variation Range
90 - 264 Vrms
1. General
2.1 Input Voltage
2.2 Input Frequency
* The power supply must operate at above frequency with 90-264 VACrms input voltage range.
2. Input Characteristics
Nominal Frequency
50-60 Hz
Frequency Variation Range
47 Hz to 63 Hz
02
2.3 Max. Input AC Current
3.1 Normal Operation Output
3. Output characteristics
Max. Input Current
ST75F-PT
ST75F-PT
ST65F-PT
ST55F-PT
2.4 Inrush Current
The power supply must meet inrush requirements for any rated AC voltage, during turn on at any phase
of AC voltage, during a single cycle AC dropout condition, during repetitive ON/OFF cycling of AC, and
over the specified temperature range. The peak inrush current shall be less than the ratings of its critical
components (including input fuse, bulk rectifiers, and surge limiting device).
2.5 Efficiency
ST75G-PT, ST65F-PT, ST55F-PT provides an efficiency of 89% minimum when measured at full load under
115V/60Hz and 230V/50Hz condition.
Maximum continuous total DC output power should not exceed750W.
Maximum continuous combined load on +3.3VDC and +5VDC outputs shall not exceed 120W.
Maximum combined load on +12V outputs shall not exceed 750W.
NOTE:
Noise test should be measured with 20 MHz bandwidth frequency oscilloscope. The output terminal shall
add a tantalum capacitor of 10uF in parallel with a ceramic capacitor of 0.1uF.
10A
Measuring Range
90 - 264 Vrms
Max. Input Current
10A
Measuring Range
90 - 264 Vrms
Max. Input Current
8A
Measuring Range
90 - 264 Vrms
Output Voltage
1. +5V
2. +12V
4. –12V
5. +5Vs
6. +3.3V
Load MIN
0.2A
0.0A
0.0A
0.0A
0.0A
Range MAX
22A
62.5A
0.3A
3.0A
22.0A
Regulation
±3%
±3%
±10%
±5%
±3%
Ripple & Noise P-P Max.
50mV
120mV
120mV
50mV
50mV
03
3.2 Remote On/Off Controlled mode
The PSON# signal is required to remotely turn on/off the power supply, PSON# is an active low signal that
turns on the output power rails. When this is not pulled low by the system, or left open, the outputs (except
the +5VSB) turn off. This signal is pulled to a standby voltage by a pull-up resistor internal to the power
supply.
TTL level "H" 2.0 V – 5.25 V
"L" 0.0 V – 1.0 V
ST65F-PT
Maximum continuous total DC output power should not exceed650W.
Maximum continuous combined load on +3.3VDC and +5VDC outputs shall not exceed 120W.
Maximum combined load on +12V outputs shall not exceed 650W.
NOTE:
Noise test should be measured with 20 MHz bandwidth frequency oscilloscope. The output terminal shall
add a tantalum capacitor of 10uF in parallel with a ceramic capacitor of 0.1uF.
Output Voltage
1. +5V
2. +12V
4. –12V
5. +5Vs
6. +3.3V
Load MIN
0.0A
0.0A
0.0A
0.0A
0.0A
Range MAX
22A
54.2A
0.3A
3.0A
22.0A
Regulation
±3%
±3%
±10%
±5%
±53%
Ripple & Noise P-P Max.
50mV
120mV
120mV
50mV
50mV
ST55F-PT
Maximum continuous total DC output power should not exceed550W.
Maximum continuous combined load on +3.3VDC and +5VDC outputs shall not exceed 105W.
Maximum combined load on +12V outputs shall not exceed 550W.
NOTE:
Noise test should be measured with 20 MHz bandwidth frequency oscilloscope. The output terminal shall
add a tantalum capacitor of 10uF in parallel with a ceramic capacitor of 0.1uF.
Output Voltage
1. +5V
2. +12V
4. –12V
5. +5Vs
6. +3.3V
Load MIN
0.0A
0.0A
0.0A
0.0A
0.0A
Range MAX
20A
45.9A
0.3A
3.0A
20.0A
Regulation
±3%
±3%
±10%
±5%
±3%
Ripple & Noise P-P Max.
50mV
120mV
120mV
50mV
50mV
04
3.5 Hold-up Time
3.3 Regulation
The cross regulation defined as follows, the output regulation should be within the specified range.
3.4 Rise Time
DC output rise time is less than 20 mS at nominal line and full load.
DC +5V output maintains at least 16mS after power off which hold within full load under 230V/50Hz
condition.
3.6 5VSB
5VSB is requierd for the implementation of PS-ON described above. 5VSB is a standby voltage that may
be used to power circuits that require power input during the powered-down state of all power rails. The
5 VSB pin should deliver 5V ±5% at a minimum of 3.0 A for PC board circuits to operate. Conversely, PC
board should draw no more than 3.0A maximum form this pin. This power may be used to operate circuits
such as soft power
Load
Light Load.
Typical Load
Full Load
+5V
2.44A
6.10A
12.20A
+3.3V
2.44A
6.10A
12.20A
+12V
10.55A
26.38A
52.75A
-12V
0.05A
0.13A
0.25A
+5Vsb
0.51A
1.27A
2.53A
ST75F-PT
Load
Light Load.
Typical Load
Full Load
+5V
2.38A
5.96A
11.92A
+3.3V
2.38A
5.96A
11.92A
+12V
8.93A
22.32A
44.65A
-12V
0.05A
0.12A
0.25A
+5Vsb
0.49A
1.24A
2.47A
ST65F-PT
Load
Light Load.
Typical Load
Full Load
+5V
2.07A
5.16A
10.33A
+3.3V
2.07A
5.16A
10.33A
+12V
7.48A
18.71A
37.42A
-12V
0.05A
0.12A
0.24A
+5Vsb
0.49A
1.22A
2.45A
ST55F-PT
05
3.7 PG-OK
3.8 3.3V Sense
PG-OK is a power good signal and should be asserted high by power supply to indicate that the +5 VDC
and +3.3 VDC outputs are above the under-voltage thresholds of the power supply. When this signal is
asserted high, there should be sufficient mains energy stored by the converter to guarantee continuous
power operation within specification. Conversely, when either the +5VDC or the +3.3VDC output voltage
falls below the under-voltage threshold, or when mains power has been removed for a time sufficiently
long so that power supply operation is no longer guaranteed, PG-OK should be deasserted to a low state.
See Figure 1 for a representation of the timing characteristics of the PG-OK,PS-ON, and germane power
rail signals.
A default 3.3V sense line should be implemented pin 13 of the connector.
3.9 Capacitive Load
The power supply should be able to power up and operate normally with the following capacitances
simultaneously present on the DC outputs.
In primary circuit of the power supply , a protected fuse is inserted. Only internal fault of the power supply
will cause the fuse blown. Any overload or short circuit at DC output will keep from fuse brown or fire hazard.
4.1 Input Protection
The +5V/+12V/+3.3V DC output are protected against the under voltage condition . range value can't
be exceed 3.3~3.7V at 5V terminal and 8.5~9.5V at 12V, 2.0~2.4V at 3.3V.
4.2 Output Protection
4.2.1 Under voltage protection
The +12V/ DC output are protected against the over voltage condition . Maximum value can't be over
15.5V at 12V.
4.2.2 Over Voltage Protection
The power supply can be used electronic circuit to limit the output current against exceeding 10%-60%
of surge output power or protected against excessive power delivery since short circuit of any output
or over total power at high line.
4.2.3 Over Power Protection
Output
+5V
+12V
+3.3V
-12V
+5VS
Capacitive load (uF)
6,000
8,000
6,000
350
350
4. Protection
06
5.1 No Load Start
5. Start Stability
Frequency
5-55-10 Hz
Duration
30 minutes
Amplitude
0.35 mm
Short circuit placed on +5V,+12V,+3.3V,-12V will latch off. +5VSB will auto-recovery.
4.2.4 Short Circuit Protection
Current protection should be designed to limit the current to operate within safe operating conditions.
Over current protection schemes where only the voltage output that experiences the over current event
is shut off may be adequate to maintain safe operation of the power supply and the system; however,
damage to the motherboard or other system components may occur. The recommended over current
protection scheme is for the power supply to latch into the shutdown state. The setting of over current
protection for each output rail is as following.
When power is applied to ST75F-PT, ST65F-PT, ST55F-PT with no load connected or under minimum
load connected, neither damage to power supply nor hazards to users will occur.
6.1 Temperature and Humidity
6. Environments
6.1.1 Operating
6.2 Altitude
The power supply can operate normally at any altitude between 0 to 10000 feet.
6.3 Vibration and Shock
Sweep and resonance search for each of X,Y,Z, axis at the sweep.
RATE of 1/OCTAVE/Min.
Temperature 0 to 40C
Relative Humidity 20 to 90 %
5.2 Cold Start
The power supply shall operate properly when first applied at normal input voltage and or so maximum
load after 4 hours storage in 0℃ environment.
4.2.5 Over-Current Protection
o
6.1.2 Storage
Temperature -40 to 70C
Relative Humidity 20 to 95 % noncondensing
o
CE,FCC
7. Conducted EMI
07
cTUVus, CB,TUV
8.1 Safety Requirement
The AC leakage current is less than 3.5mA when the power supply connect to 264Vac/50Hz .
8.2 Leakage Current
The insulation resistance should be not less than 30M ohm after applying of 500VDC for 1 minute.
8.3 Insulation Resistance
The power supply shall withstand for 1 minute without breakdown the application of a 60Hz 1500V AC
voltage applied between both input line and chassis (20mA DC cut-off current). Main transformer shall
similarly withstand 3000Vac applied between both primary and secondary windings for a minimum of one
minute.
8.4 Dielectric Voltage Withstand
8. Product Safety
A TTL compatible signal for the purpose of initiating an orderly start-up procedure under
normal input operating conditions. During power up, this signal is asserted ( low ) until
+5V is under regulation and AC reaches min. line specification range. After all voltage
are going appropriate level, the system may have a turn on delay of 100mS, but no
greater than 500mS. During power off the signal should go to low level before +5V
is out of regulation. The low level is 0 to 0.8V and high level is 4.75 to 5.25V. The
" Power Good "signal can drive up to 6 standard TTL loads.
9. Power Good Signal
* T1 : Turn on time ( 2 sec. Max.)
* T2 : Rise time ( ≦ 20mS Max.)
* T3 : Power good turn on delay time ( 100 < T3 < 500 mS )
* T4 : Switch on time (0.5 sec. Max.)
* T5 : Power good turn off delay time ( 1.0 mS Min.) PS-ON/OFF
* T6 : Power hold-on time ( 16 mS Min.)
* Power on-off cycle :
When the power supply is turned off for a minimum of 2.0 sec. and turn on again, the power good signal will be
asserted.
Time Diagram Figure 1
08
The power supply with active power factor correction, and meet the EN61000-3-2
standards, The power factor is greater than 0.9 at 230V/50Hz, Max. load.
13. Power Factor
150 mm (W) × 86 mm (H) × 140mm (D)
14. Mechanical Specification
The MTBF of the power should be 100,000 hours min.
10. MTBF
11.1 Input Voltage
Applying 220Vac for 230V model.
11.2 Test Condition
Applying 75% loads for the power supply in 45 (+/-5) oC chamber for 4 hours.
11. Burn-In
The product shall meet requirement for EN61000-3-2 & EN61000-3-3 :1995 standard
of class D, test at 230Vac 50Hz.
12. Harmonics
NO. G11224800
