SAVE THIS MANUAL: KEEP THIS MANUAL FOR SAFETY WARNINGS, PRECAUTIONS, ASSEMBLY,
OPERATING, INSPECTION, MAINTENANCE AND CLEANING PROCEDURES. WRITE THE PRODUCT’S
SERIAL NUMBER ON THE BACK OF THE MANUAL NEAR THE ASSEMBLY DIAGRAM (OR MONTH
AND YEAR OF PURCHASE IF PRODUCT HAS NO NUMBER)
OWNER’S MANUAL AND SAFETY INSTRUCTIONS
SURFACE FINISHING RULER TAMPER
ITEM: 61008/61013
FOR QUESTIONS PLEASE CALL OUR CUSTOMER SUPPORT: (909) 628 4900 MON-FRI 9AM TO 3PM PST
IMPORTANT SAFETY INFORMATION
GENERAL SAFETY WARNINGS
Read all safety warnings and instructions. Failure to follow the warnings and instructions may result
in electric shock, re and/or serious injury. Save all warnings and instructions for future reference.
SAFETY
WARNING DO NOT use this product or any available optional equipment without rst completely reading
and understanding these instructions and any additional instructional material such as owner’s manuals,
service manuals or instruction sheets supplied with this product or optional equipment. When using an
electrical appliance, basic precautions MUST be followed to reduce the risk of re, electric shock and
personal injury.
1
DO NOT operate the machine unless all protective guards are in place.
KEEP hands and feet clear of rotating and moving parts as they will cause injury if contacted.
ENSURE that the motor operation switch is in the OFF position and the spark plug ignition lead is
disconnected before removing the guards or making adjustments.
DO NOT leave the machine in operation while it is unattended.
EXERCISE CARE when operating unit. Exposure to Vibration or repetitive work actions may be harmful
to hands and arms.
NEVER stand on the unit while it is operating.
BE CAREFUL not to come in contact with the muffler when the engine is hot, it can cause severe burns.
ENSURE that repairs to the motor and machine are carried out by COMPETENT personnel.
PETROL is extremely flammable and explosive under certain conditions. ENSURE that petrol is only
stored in an approved storage container.
DO NOT refuel the motor while it is in operation or hot.
DO NOT refuel the motor in the vicinity of sparks, a naked flame or a person smoking.
DO NOT over fill the fuel tank and avoid spilling petrol when refueling. Spilled petrol or petrol vapor
may ignite. If spillage occurs, ensure that the area is dry before starting the motor.
ENSURE that the fuel tank cap is securely fitted after refueling.
DO NOT operate or refuel a petrol motor in a confined area without adequate ventilation.
CARBON MONOXIDE exhaust gases from internal combustion motor driven units can cause death in
confined spaces.
EXCESSIVE NOISE can lead to temporary or permanent loss of hearing.
WEAR an approved hearing protection device to limit noise exposure. As required by Occupational
Health and Safety regulations.
2
IMPORTANT SAFETY INFORMATION
ALWAYS wear protective clothing and footwear to prevent the skin coming into contact with wet concrete.
PROTECTIVE FOOTWEAR should be worn to reduce injuries from penetration through the sole，contact
with cutting objects, slipping, contact with wet concrete and electrical hazards.
USE waterproof protection for hands and knees(if kneeling)when concreting. If your clothing becomes
wet from concrete contact make sure you change the clothing. DO NOT walk about waiting for it to dry.
Slip/Trip/Fall is a major cause of serious injury or death. Beware of uneven or slippery work surfaces.
Inspect the rubber anti vibration mounts for wear or deterioration. Clean the aluminium beams regularly
to prevent a build up of concrete residue.
CARE AND PREVENTATIVE MAINTENANCE
The housing weight must be greased after every 10 hours of operation. DO NOT over grease.
Inspect and clean and/or replace the motor air cleaner regularly, particularly when operating in a dusty
environment.
Inspect, clean and/or replace the spark plug regularly .
Check all fasteners for tightness as the machine is subject to vibration.
To test run the screed support the beams on a resilient support at each end.
Keep the unit clean and free of concrete residue.
Ensure the cooling ns on the motor are kept unobstructed.
SAVE THESE INSTRUCTIONS.
3
OPERATION
SPECIFICATIONS
USING THE VIBRATING-BEAM SCREED
Once the concrete with its surcharge has been spread, start the motor and manually pull the beam along
the slab. Make sure that there is always a continuous surcharge along the entire length of the leading
edge
Generally one steady pass with the screed should be enough to compact and level the concrete.
Vibration of the concrete is still necessary to bring air bubbles to the surface.
WEIGHT OF BLADES
The total weight of the machine should be the weight of engines assembly plus weight of blades
TROUBLESHOOTING
4
DISCLAIMER
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only and are not available individually
as replacement parts.
PRODUCT MADE IN CHINA
5
