G4GEMTIF10B1000 1360100497 Curtis Gemini G4 Coffee Brewer User Manual

Important Safeguards/Conventions

This appliance is designed for commercial use. Any servicing other than cleaning and preventive maintenance

should be performed by an authorized Wilbur Curtis service technician.

 •DONOTimmersetheunitinwateroranyotherliquid

 •Toreducetheriskofreorelectricshock,DONOTopenservicepanels.Nouserserviceableparts

inside.

 •Keephandsandotheritemsawayfromhotsurfacesofunitduringoperation.

 •Nevercleanwithscouringpowders,bleachorharshchemicals.

Symbols

WARNINGS – To help avoid personal injury

Important Notes/Cautions – from the factory

Sanitation Requirements

YourIntelliFreshbrewerisFactoryPre-SetandReadytoGo…RightfromtheBox.

FollowingaretheFactorySettingsforIntelliFreshbrewer:

•BrewTemperature=200°F  •WaterBypass=OnLARGE&MEDIUMbrewonly

•BrewVolume=Large-Medium-Small •EnergySaveMode=Off

•QualityTimer=120Minutes

SystemRequirements:

 •WaterSource20–90PSI(MinimumFlowRateof1GPM)

 •Electrical:Seeattachedschematicforstandardmodelorvisitwww.wilburcurtis.comforyourmodel.

SETUPSTEPS

Theunitshouldbelevel(lefttorightandfronttoback)andlocatedonasecurecountertop.Connectawater

linefromthewaterltertothebrewer.

NOTE:Awaterltrationsystemmustbeusedtomaintainatrouble-freeoperation.(Inareaswithextremely

hardwater,wesuggestthatasedimentaryandtaste&odorlterbeinstalled.)Thiswillprolongthelifeofyour

brewingsystemandenhancecoffeequality.

1.A3/8”Flarex3/8”Malepipeelbowissuppliedwiththebrewerforwaterlineconnection.Usetubingsized

sufcientlytoprovideaminimumof1.0GPM.

2.Connecttheunittoanappropriateelectricalpowercircuit.

3.Turnonthetoggle(STANDBY/ON)switchbehindtheunit.Theheatingtankwillstarttoll.Whenthewater

levelinthetankrisestothecorrectvolume,theheatingelementswillenergizeautomatically.Withthe

IntelliFreshbrewer,thereisnodangerofelementburnoutcausedbyoverheatinganemptytank.

4.Theheatingtankwillrequire20to30minutestoreachoperatingtemperature(200°F),indicatedwhen

READYTOBREWisdisplayedontheLCDscreen.

5.Priortobrewing,dispense12ouncesofhotwaterthroughthehotwaterfaucet.

6. Brewacycleofatleast12ounces,topurgethewaterlinesofanyairthatmaybetrappedafterlling.

NSF International requires the following water connection:

1. A quick disconnect or additional coiled tubing (at least 2x the depth of the unit) so that the ma-

chine can be moved for cleaning underneath.

2. Insomeareasanapprovedbackowpreventiondevicemayberequiredbetweenthebrewerand

the water supply.

Wilbur Curtis Company, inC.

Models

GEMTIF

GEMSIF

GEM3IF

ServiceManual–GeminiIntelliFreshBrewer

CAUTION: DO NOT

connect this brewer to hot

water. The inlet valve is

not rated for hot water.

CAUTION: Please use

this setup procedure

before attempting to use

this brewer. Failure to follow the

instructions can result in injury or the

voiding of the warranty.

IMPORTANT: Equipment

to be installed to comply

with applicable federal,

state, or local plumbing/electrical

codes having jurisdiction.

FOR THE LATEST SPECIFICATIONS AND INFORMATION GO TO WWW.WILBURCURTIS.COM

ISO9001:2008

Wilbur Curtis Company

Montebello,CA90640

Tel:(323)837-2300

www.wilburcurtis.com

GEMINI IF BREWER

SATELLITE

UCM CONTROL

IF CONNECTOR

INTELLIFRESHFUNCTION&FEATURES

The IntelliFresh system is a method of storing coffee to maintain freshness and alert

youwhenthecoffeehasexceededthedesiredholdingtime.BeingaGEMINIsys-

tem,coffeeisbreweddirectlyintoanIntellifreshSatellitecontainer.TheSatellites

arelinkedtothebrewerbyaconnector.TheIntellifreshsystemisactivatedwhen

theconnectorontheSatellitecomesintocontactwithacorrespondingconnector

onthecenterpanel.TheSatellitecontainstwomaincontrolfunctionsbuiltintothe

server.

TEMPERATURE: Thissystemallowsyoutoselecttheholdingtemperature

withintheSatellite.Therearethreetemperaturesettingstochoosefrom:HIGH,

MEDIUMandLOW.ThefactorydefaultisMEDIUM.Thetemperatureisadjust-

ablethroughtheUCMcontrolpanelonthebrewer.

TIMER: Thetimerdoestwothings.Itturnsonandoffaredindicatorlightand

turnsoffthewarmerelement.ThetimerisalsoprogrammablethroughtheUCM.

Theindicatorlightsignalswhenapredeterminedtimehasexpired.Thewarmer

shutsoff12hoursaftertheindicatorlightcomeson.

WARNING: TOAVOIDSCALDING,Donotremovebrewconewhilebrewlightisashing.

1.BrewershouldbeON(Conrmatreartoggleswitch,thenpresstheON/OFFbutton).Ready-to-Brewshouldbeonthedisplay.Ifthe

brewerisconnectedtoanInterLockgrinder,thegrindershouldbeon.WhenInterlockconnectionismade,grindcoffeeatthistime.

2.PlaceanemptySatelliteunderthebrewconeandpressthewarmerswitchtopre-heattheSatellite.

NOTE: Only utilize Intellifresh Satellites on Intellifresh Brewers.

6. Pressappropriate

brewbutton.

Brewingwillbegin

immediately.

5. Transferlledbrew-

conetobrewer.

3. Placeacleanlter

intothebrewcone.

4. Fillbrewconewith

ground coffee.

INTELLIFRESHBREWINGINSTRUCTIONS

Atthebeginningofthebrew-

cycle,theLEDontheSatellite

comes on and stays lit during

thequalitytimesetting.Range

20min–240min,in10minute

increments.

Whenqualitytimeexpires,

LEDwillashfor12hours.

After12hoursofashing,the

LEDandwarmerwillturnoff.

TheLEDabovethewarmerbuttonontheUCMwillsimultaneouslyduplicatethelightpatternontheSatellite.

Ifanewbrewcycleisstartedbeforethequalitytimerhasexpired,thetimerwillresetandbegincountingdownagain.

ERROR MESSAGE DESCRIPTION CAUSE

(900) 000-0000 EXT (0000)

Water Level ERR.

Fill run error/OverflowThe fill solenoid has either run for

more than 10 minutes on the initial

tank fill or 1 minute, 30 seconds in

normal operation.

Break in the temperature thermistor

circuit.

Open Probe(900) 000-0000 EXT (0000)

Sensor Error

(900) 000-0000 EXT (0000)

Over Temp. Error

Excess Temperature

The sensor is reading the tempera-

ture in the heating tank has risen

above 210ºF.

1-(800)-000-0000

Water Level Error

1-(800)-000-0000

Sensor Error

1-(800)-000-0000

Over Te mp. Error

Error Message

Anerrormessagewillappearonthescreenintheeventofamalfunctionunderthefollowingconditions:

1.WaterLevelOverow.

2.BreakinTemperature

Control Circuit

3.ExcessTemperaturein

HeatingTank

Toturnoffanerrormessage,

press the buttonforve

seconds.

Warmers

Thewarmer,underthebrewconewillturnonautomatically

wheneveracoffeebrewcycleisstarted.Thewarmersmay

beswitchedonandoffusingtheWARMERbuttonsonthe

control panel.

CLEANING

Regularcleaningofyourcoffeebrewerwillmaintainthehighestqualitycoffeeyourequipmentiscapableofproducing.Apropercleaningis

essentialinpreservingtheappearanceofthebrewer.

1. Turnofftheunitatthebuttononthefrontcontrolpanel.

2. Wipeexteriorsurfaceswithadampcloth,removingspillsanddebris.

3. Slidethebrewconeoutandcleanit.Thoroughlysoapthesprayheadareawithamilddetergentsolution.

4. Washthebrewbasket.Useasoftbristledbrushforhardtocleanareas.Washbothpartswithadetergentsolutionorputtheseparts

throughadishwasher.

CAUTION: DO NOT use undiluted bleach or chlorine.

LEFT & RIGHT

SATELLITE WARMERS

Curtis

Ready

Entering

Programming Mode

Enter Code

- - - -

Program Menus

<-- Select -->

Global Recipes

<-- Select -->

Gourmet STD

<-- Select -->

Light Roast

<-- Select -->

Dark Roast

<-- Select -->

High Yield

<-- Select -->

Filter Pack

<-- Select -->

Decaf

<-- Select -->

Exit

<-- Select -->

Non-Brew Prog

<-- Select -->

Temperature

<-- Select -->

Energy Save Mode

<-- Select -->

Brew Count Odom

<-- Select -->

Quality Timer

<-- Select -->

Brew Count Total

<-- Select -->

Cold Brew Lock

<-- Select -->

Master Reset

<-- Select -->

Service Call

<-- Select -->

Acess Code

<-- Select -->

Banner Name

<-- Select -->

P-Maintenance

<-- Select -->

Beeper On/Off

<-- Select -->

Drip-Out Mode

<-- Select -->

Warmers Default

<-- Select -->

Exit

<-- Select -->

Brew Button Prog

<-- Select -->

Select Button…

<-- Select -->

Brew By Volume

<-- Select -->

Brew By Time

<-- Select -->

Pre-Infusion

<-- Select -->

Pulse Brew On/Off

<-- Select -->

Bypass On/Off

<-- Select -->

Exit

<-- Select -->

One Batch

<-- Select -->

Two Batch

<-- Select -->

Three Batch

<-- Select -->

Exit

<-- Select -->

Model Select

<-- Select -->

ThermoPro Twin

<-- Select -->

ThermoPro Single

<-- Select -->

Gemini - Single

<-- Select -->

Gemini - Twin

<-- Select -->

Milano Twin

<-- Select -->

Milano Single

<-- Select -->

Gemini - Twin IF

<-- Select -->

Gemini - Single IF

<-- Select -->

Display Brew Time

<-- Select -->

Warmers Auto-Off

<-- Select -->

TheG3/GoldCupSeriesBrewingSystemisFactoryPre-SetforOptimumPerformance.

Afterconnectiontowaterandpower;thereartoggleswitchmustbeon.Youwillhearabeepsound,indicatingpowerisavailabletothecontroller.

Thecontroldisplays  .PressON/OFFbuttonandthescreenwilldisplay  .Afterthreeseconds,  isdisplayed.

Waterwillllthetank(approximately2-3minutesdependingonwaterowrate).Whentheproperlevelisreached  willappearonthe

screen.Ittakesapproximately20minutestoreachsetpointtemperatureof200°F.

Controlwilldisplay  whentemperaturereachesthesetpoint(200°F).Unitisnowreadytobrew.

<GEMINITWIN>

WILBURCURTIS

CURTIS CURTIS

FILLING

CURTIS

HEATING

CURTIS

READYTOBREW

PROGRAM MENUS

All programming selections are performed with the three center

buttons.

The symbols below the buttons are:

Scroll LEFT

 SELECTION or ENTER to save new parameter

Scroll RIGHT

IMPORTANT NOTE:

GEM INTELLIFRESH

Program Menus GEMIF Brewer

Program Menus

Temperature

Energy Save Mode

Brew Count Odom

Global Recipes

Banner Name

Access Code

Service Call

Master Reset

Cold Brew Lock

Brew Count Total

From Program Menus press>displaywillshowthenextfeatureGlobalRecipes.

Quality Timer

NON-BREW PROGRAMMING

Temperature(Factorysetto200ºF)

PresstoSelect.Press<or>tomovetodesiredtemperatureandthen to set. Temperature is programmable from

170ºFto206ºFin2-degreeincrements.

Energy Save Mode (FactorysettoOFF)

PresstoSelect,<or>ON,OFForON140ºF,toset.WheninON,unitwillautomaticallyshutoff4hoursfromlast

brew.WhenfeatureisOFF,unitdoesnotutilizetheenergysavingmode.

IntheON140ºFposition,temperaturelowersto140ºF,ifunithasnotbrewedin4hours.Thisfeaturewillsaveenergyby

maintainingalowertemperatureinthetankinperiodsofnon-operation.

Brew Count Odom

Presstodisplaytotalbrewcycles.PressEXorReset.

Quality Timer (Factorysetto120Minutes)

Press to select,press<or>tochoosedesiredsetting.Range20min–240min,in10minuteincrements.The timer

doestwothings.Itturnsonandoffaredindicatorlightandturnsoffthewarmerelement.Theindicatorlightsignalswhena

predeterminedtimehasexpired.Thewarmershutsoff12hoursaftertheindicatorlightcomeson.

Brew Count Total

PresstoSelect,Showstotalgallonsandtotalbrewcyclesontheunit.Notresettable.

Cold Brew Lock ...(Factorysetto5º)

Presstoselect,<or>toselectdesiredsetting(CBL5,15orOFF), to set.

TheColdBrewLockfeatureallowsthebrewertobrewatthreedifferenttemperaturelevelsfromtheactualsetpoint.The

rstsettingiswithin5degreesofsetpoint,nextiswithin15degreesofsetpoint,OFFiswithin30degreesofsetpointfor

theReadytoBrewmessage,however,itwillbrewatanytemperature.

Master Reset

Press to display Are You Sure?

Then<forYes,>forNo.Brewerfactorydefaultsarethenreset.

Service Call (PhonenumberFactorysetto1-800-000-0000X0000)

Presstodisplaynumberandchangenumberor<tomoveplaceandEXtoexitwhencomplete.Thisnumberwillbe

displayedduringaHeatingsystemSENSORERRORorduringaWATERERROR.

Access Code(Factorysetto1-2-3-4)

Presstodisplaynumberandchangenumber,(thenumbercanbechanged1to4)or<tomoveplaceandEXtoexit

whencomplete.

Banner Name(FactorysettoCURTIS)

Presstodisplaylettersandchangelettersor<tomoveplaceandEXtoexitwhencomplete

Thisfeatureallowsupto14letterstobeprogrammedforcompanynameorregionalname.Programmingallblanksdis-

ablesBannerName.Ifprogrammed,BannerNameisdisplayedevery5sec.onandoff.

Warmers Auto – Off(FactorysettoMEDwhilebrewing)

PresstoSelect.Press<or>toadjustfrom1hourto12hours.Thisfeatureadvancesin1hourincrements.

GLOBAL RECIPES

Global Recipes(FactorysettoGourmetSTD)

Presstoselect.Ifselected,press <or>tochosearecipebasedonthetypeofcoffeebeingbrewed.Selectionsare

GourmetSTD,LightRoast,DarkRoast,HighYield,FilterPack,orDecaf.Press to select the desired recipe.

Warmers Auto-Off

Program Menus GEMIF Brewer

P-Maintenance

Brew By Time

Brew By Volume

Displ. Brew Time

Pre-infusion

Pulse Brew

By-Pass

Model Select

P-Maintenance(FactorysettoOFF)

PresstoSelect,SetgallonsbrewedtoindicateP-Maintenance.Press<or>toadjustfromOffto9500gallons.This

featureadvancesin100gallonincrements.Presstoexit.

Beeper On/Off (FactorysettoON)

PresstodisplayONorOFF.Pressingeither<or>togglesbetweenonandoff.toset.WhenON,thisfeatureallows

you to hear a short beep each time a button is pressed.

Drip-out Mode (Factorysetto2minutes)

PresstoSelect.Press<or>tomovetodesiredtime.SettingsareOFF,1,2,3,4and5minutes.Press to Select

time.

Warmers Default(Factorysetting-MED)

PresstoSelect.Press<or>toadjustfromOFF,HIGH,MEDorLOW.PowersettingforHIGHis100WwattsMEDis

82watts.LOWis66watts.

Displ. Brew Time (FactorysettoON)

PresstodisplayONorOFF.Pressingeither<or>togglesbetweenonandoff.AfterDisplayBrewTimeanEXITscreen

willreturnyoutoNon-BrewProg.

Drip-out Mode

Beeper On/Off

Warmers Default

BREW BUTTON PROGRAMMING

Brew by Volume(Factorysettings:LARGE200oz±8oz.MEDIUM132oz±4oz.SMALL64oz±4oz.)

PresstoSelect.Displaywillaskyoutoselectabrewbutton,Large,MediumorSmall.Pressthedesiredbrewbuttonto

begin...whendesiredvolumeisreachedpressthesamebrewbuttontostoptheow.Nowthevolumehasbeenset.

Brew by Time(Factorysettings:LARGE5min-25sec.MEDIUM3min-32sec.SMALL1min-52sec.)

NextiteminthesequenceisBrewbyTime.PresstoSelecttochangethebrewtime.Displaywillnowshowthecurrent

time.Bypressing<or>youcantogglebackandforthfromminutestosecondstoexit(ex).Changethetimeorsetandexit

by pressing the  button.

Pre-Infusion(FactoryDisabled)

PresstoSelect.Currentsettinginsecondsisdisplayed<todecreaseorselect>toincrease(rangefromOFFto10

through60seconds), to set.

IfPre-infusionisselected(ON),ColdBrewLockissetwithin5ºFofsetpointandColdBrewLockdisappearsfromthelistof

programselections.WhenPre-infusionisON,PulseBrewdisappearsfromthelistofprogramselections.

Pulse Brew(FactorysettingC)

Presstoselect,<or>toselectOFForoneofvepulsepatterns(AtoE).ThevePulseBrewoptionshelp“tune”or

changethecoffeeavor.

GuidelinesforPulseBrew:

FilterPacktypecoffeestypicallyextractbetterwiththeA and B pulse setting.

DecafcoffeestypicallyextractbetterwiththeB pulse setting.

High-YieldcoffeestypicallyextractbetterwiththeCpulsesetting.Ofcourse,anyoftheA, B or C settings may be used to

suityourtasteprole.

Settings D and E are manual pulse counts.

ToexitfromthePulseBrewmode,select0 for the time.

IfPulseBrewison,ColdBrewLockissetwithin5ºFofsetpointandColdBrewLockdisappearsfromthelistofprogram

selections.WhenPulseBrewison,Pre-infusiondisappearsfromthelistofprogramselections.

By-Pass (Factorysettings:LARGE35%.MEDIUM10%.SMALLOff.)

TheBy-Passoptionhelpswithcontrollingextractionwithlargerbrews.Contacttimethatistoolongwillextractundesirable

bitter,harshavorcompounds.By-passingsomeofthebrewwateraroundthecoffeebedwillbalancetheextraction.

Presstodisplaycurrentsetting.Press<or>tochangesettings;OFF,5%to50%,in5%increments.Press to set.

Model Select(FactorysettoGemini-TwinIF)

Presstoselect,<or>toselectmodel.Theselectionsare:ThermoPro-Twin,ThermoPro-Single,Gemini-Twin,Gemini-

Single,Milano-Twin,Milano-Single,Gemini-TwinIF,andGemini-SingleIF.Presstoset.WhentheModelSelectfeatureis

changed,allsettingsareresettothedefaultsofthenewlyselectedmodel.

Illustrated Parts List

GEMTIF

GEM3IF

WC-37121*

WC- 442

WC-2977-101

WC- 844-101*

WC-39744

WC-37388*

WC-39755*

WC-39756*

WC-29050*

WC-8559*

WC-37308*

WC-39745

WC-61309

WC-61307

WC-38504

WC-61301

WC-37008*

WC-43067*

WC-37406*

WC- 934-04*

WC-4382*

WC-1438-101*

WC-62033

WC-29044

WC-2402P*

WC- 847 *

WC-37122 *

WC-1501*

WC- 102*

WC- 522 *

WC-43055*

WC-5421

WC-3528 *

WC-1809*

WC-5310*

WC-5231*

WC-3765L*

WC-13429

WC-13428

WC-37132*

WC-5350*

WC-61674

WC-37266*

WC-37317*

WC-37365*

SATELLITE, INTELLIFRESH

DUMP VALVE LEFT

SOLENOID, LOCK BREW CONE RIGHT 120V

FITTING, SPRAYHEAD ULTEM

VALVE, BY-PASS, NON-ADJUSTABLE W/RSTRCTR

LABEL, UCM & OUTER 3-BATCH GEM-IF

KIT, LABEL & UCM GEMTIF 3-BATCH CURTIS

LABEL, UCM OVERLAY 1-BATCH

LABEL, UCM OVERLAY 2-BATCH

SPRAYHEAD, AFS-AMBER

RELAY, SOLIDSTATE 40A W/HEAT SINK

BREWCONE, BLACK NON-METAL GEM

LABEL, BOTTOM PANEL

COVER, FRONT CENTER WRAP WELD ASSY GEMTIF

HOLDER, CONNECTOR FEMALE GEMTIF

LABEL, WARNING SHOCK HAZARD

DECK, WARMER WELD ASSY GEMTIF

KIT, TANK LID ROUND

O’RING, 4.5” ID SILICONE

KIT, LIQUID LEVEL PROBE FAIL-SAFE, NON-METAL

ELEMENT HEATING 2.5KW 220V

GUARD, SHOCK HEATING ELEMENT

SENSOR, HEATING TANK

TANK, COMPLETE GEMTS NON-METAL FITTINGS

SLEEVE, OVERFLOW ASSY GEN USE

ELBOW, 3/8”FL x 3/8” NPT PLATED

VALVE, INLET 2 GPM 120V 10W GEN USE YEL BODY

DUMP VALVE RIGHT

FUSE HOLDER ASSY W/5A FUSE

SWITCH, TOGGLE NON-LIT SPST 15A 125/250VAC

THERMOSTAT, RESET

GUARD, SHOCK RESET T-STAT

COVER, TOP SS GEM

LEG, 4” ADJUST 3/8-16 THREAD STYLIZED

FAUCET, PS/HPS SERIES HOT WTR

TUBE, 5/16 ID x 1/8W SILICONE

COMPOUND, SILICONE

KIT, VALVE REPAIR USE ON WC-847

HARNESS ASSY IF CONNECTOR RT

HARNESS ASSY IF CONNECTOR LT

KIT, VALVE REPAIR USE ON WC-844-101

TUBE, SILICONE Ø1/2” ID x Ø3/4” OD x 1/8” WALL

BRACKET, BREWCONE ALIGNMENT

KIT, TANK OVERFLOW FITTING WITH BUSHING

KIT, STRAIGHT FITTING WITH BUSHING

KIT, TANK INLET FITTING WITH BUSHING

Description

Index

Nº

Part Nº

Illustrated Parts List

GEMTIF

* SUGGESTED PARTS TO STOCK

Illustrated Parts List

GEMSIF

Illustrated Parts List

GEMSIF

GEM3IF

WC-58117

WC-37122*

WC-2977-101

WC-37308*

WC- 442

WC- 844-101*

WC-37389

WC-39801*

WC-39802*

WC-39803*

WC-8559*

WC-61384

WC-39800

WC-1809*

WC-61307

WC-3528 *

WC-61379

WC-2402P*

WC-1501

WC-59020

WC- 102*

WC- 847 *

WC-29050*

WC-5853-102

WC-43062*

WC-37406*

WC-62035

WC- 906-04*

WC-1438-101*

WC-4394*

WC- 522 *

WC-43055*

WC-5310*

WC-5231*

WC-3765L*

WC-13429

WC-38504

WC-37266*

WC-37317*

WC-37365*

WC-37132*

WC-29044

SATELLITE, INTELLIFRESH

COVER TOP

DUMP VALVE RIGHT

FITTING, SPRAYHEAD ULTEM

BREWCONE, BLACK PLASTIC GEM

SOLENOID, LOCK BREWCONE L/R LABEL

VALVE BY-PASS NON-ADJUSTABLE

KIT, LABEL & UCM GEMSIF 3-BATCH CURTIS

LABEL, UCM PANEL 3-BATCH GEMSIF

LABEL, UCM PANEL 2-BATCH GEMSIF

LABEL, UCM PANEL 1-BATCH GEMSIF

RELAY, SOLIDSTATE 40A W/HT SINK

COVER, FRONT CENTER WRAP GEMSIF

LABEL, BOTTOM WRAP GEMSIF

FAUCET, PS/HPS SERIES HOT WTR

HOLDER, WC-571 FEMALE IF CONNECTOR

LEG, 4” ADJUST 3/8-16 THRD STYLIZED

DECK, WARMER W/A

ELBOW, 3/8”FL x 3/8” NPT PLATED

FUSE HOLDER ASSY W5A FUSE

PANEL, BACK GEMSS

SWITCH, TOGGLE NON-LIT SPST 15A 125/250VAC

VALVE, INLET 2 GPM 120V 10W GEN USE YEL BODY

SPRAYHEAD, AFS-AMBER

COVER, TOP HEATING TANK

GASKET, TANK LID

KIT, PROBE LIQUID LEVEL NON-METAL

TANK, COMPLETE GEMSS W/ULTEM FITTINGS

KIT, ELEMENT, HEATING 2KW 220V

SENSOR, HEATING TANK

GUARD, SHOCK HEATING ELEMENT

THERMOSTAT, RESET

GUARD, SHOCK RESET THERMOSTAT

TUBE, 5/16 ID x 1/8W SILICONE

COMPOUND, SILICONE

KIT, VALVE REPAIR

HARNESS ASSY IF CONNECTOR RT

LABEL, WARNING SHOCK HAZARD

KIT, TANK OVERFLOW FITTING WITH BUSHING

KIT, STRAIGHT FITTING WITH BUSHING

KIT, TANK INLET FITTING WITH BUSHING

KIT, BY-PASS VALVE USE ON WC-844-101

SLEEVE, OVERFLOW ASSY GEN USE (NOT SHOWN)

Description

Index

Nº

Part Nº

* SUGGESTED PARTS TO STOCK

Illustrated Parts List

GEM3IF

Description

Index

Nº

Part Nº

* SUGGESTED PARTS TO STOCK

Illustrated Parts List

GEM3IF

A daily routine of cleaning the GEM3IF Satellite will maintain the appearance of the unit and ensure great tasting cof-

fee.

CAUTION – Do not use cleansers, liquids containing bleach, powders or any other substance containing chlo-

rine. These products promote corrosion and will pit the stainless steel. USE OF THESE PRODUCTS WILL

VOID THE WARRANTY.

CLEANING THE GEM3IF SATELLITE

To clean the Satellite components, prepare a mild detergent solution.

1. Remove lid from Satellite.

2. Turn the lid over and clean the funnel area, preferably with a gauge glass brush.

3. Rinse the lid, removing all traces of cleaning solution.

4. Unscrew the handle/bonnet assembly and remove from faucet.

5. Remove seat cup from stem and inspect for wear or hardening. Replace if necessary.

6. Clean all parts, including faucet body, with mild detergent and warm water. Thoroughly rinse with clear warm

water.

7. Dry and assemble. Hand-tighten the handle assembly.

8. Remove the gauge glass tube by unscrewing the gauge glass cap.

9. Clean the tube and washers with a gauge brush and washing solution. Rinse with clear water. Dry and as-

semble.

10. Clean inside Satellite with a cloth or ScotchBrite™ pad.

11. Remove coffee residue using a mild detergent solution with water.

12. Thoroughly rinse with clear warm water.

WC-5622*

WC-2001

WC-2005*

WC-2025*

WC-2010C

WC-2006*

WC-2102

WC-39747

WC-2007

WC-6417

WC-1901A

WC-1800*

WC- 976-101*

WC- 586*

WC-39746

WC- 736-101*

WC-3705*

WC-38151

WC-13426

WC-39747

LID, BLACK PLASTIC GEM-3

CAP, SHIELD W/VENT

WASHER, SHIELD CAP 1/8”

GLASS, GAUGE 8”

SHIELD, GAUGE GLASS ¾” D. x 8”

WASHER, .188ID x .188 THK BOTTOM

GAUGE GLASS ASSEMBLY 8”

LABEL, SIDE GEM3IF CURTIS LOGO

BRACKET, GAUGE GLASS GEM-3

GUARD, FAUCET GEM-3

SHANK, FAUCET W/SHIELD BASE

FAUCET, S’ SERIES NON-LOCKING

HEATER, SILICONE 120V 71W W/TERMINALS

LED, 5MM W/HOLDER & WIRES

LABEL, FRONT GEM3IF CURTIS LOGO

BOARD, HYBRID T-STAT CNTRL W/TRMNLS

KIT, FAUCET S’ SERIES

LABEL, LOCK/UNLOCK GEM3

IF CONNECTOR, FEMALE W/WIRES

LABEL, SIDE GEM-3IF CURTIS LOGO

5200

7600

23.6

34.5

Electrical Schematic

GEMTIF

Electrical Schematic

GEMSIF(-10Only)

Electrical Schematic

GEM3IF

SHOWING WC-37259

BREW CONE ASSEMBLY

.125”

(.3 cm)

.25”

(.6 cm)

1.0”

(2.5 cm)

30.5”

(77.5 cm)

4.0”

(10.0 cm)

5.375”

(13.7 cm)

7.75”

(19.7 cm)

11.75

(29.8 cm)

11.25”

(28.6 cm)

18.125”

(46.1 cm)

22.125”

(56.2 cm)

12.0”

(30.5 cm)

11.75”

(29.8 cm)

.75”

(1.9 cm)

7.75”

(19.7 cm)

4.0”

(10.2 cm)

5.625”

(14.3 cm)

30.5”

(77.5 cm)

11.625

(29.5 cm)

11.875”

(30.2 cm)

9.125”

(23.2 cm)

22.125”

(56.2 cm)

13.25”

(33.7 cm)

9.0”

(22.9 cm)

11.5”

(29.2 cm)

10.25”

(26.0 cm)

10.0”

(25.4 cm)

11.75”

(29.8 cm)

9.0”

(22.9 cm)

GEMTIF

GEM3IF

GEMSIF

Rough-In Drawings

This Page Intenionally Left Blank

ECN 12835 . 12/27/[email protected]

ECN 12640 . 9/30/[email protected]

ECN 12400 . 6/15/10 @ 12.7

edr 7091 . 3/23/10 @ 12.2

Printed in U.S.A. 12/10 . F-3691 . rev C

WILBUR CURTIS CO., INC.

6913AccoSt.,Montebello,CA90640-5403USA

Phone:800/421-6150 Fax:323-837-2410

TechnicalSupportPhone:800/995-0417(M-F5:30A-4:00PPST) E-Mail:[email protected]

WebSite:www.wilburcurtis.com

Product Warranty Information

TheWilburCurtisCompanycertiesthatitsproductsarefreefromdefectsinmaterialandworkmanshipundernormaluse.Thefollowinglimited

warranties and conditions apply:

3 Years, Parts and Labor, from Original Date of Purchase on digital control boards.

2 Years,Parts,fromOriginalDateofPurchaseonallotherelectricalcomponents,ttingsandtubing.

1 Year,Labor,fromOriginalDateofPurchaseonallelectricalcomponents,ttingsandtubing.

Additionally, the Wilbur Curtis Company warrants its Grinding Burrs for Forty (40) months from date of purchase or 40,000 pounds of coffee,

whichevercomesrst.StainlessSteelcomponentsarewarrantedfortwo(2)yearsfromdateofpurchaseagainstleakingorpittingandreplace-

ment parts are warranted for ninety (90) days from date of purchase or for the remainder of the limited warranty period of the equipment in which

the component is installed.

All in-warranty service calls must have prior authorization. For Authorization, call the Technical Support Department at 1-800-995-0417. Effective

date of this policy is April 1, 2003.

Additional conditions may apply. Go to www.wilburcurtis.com to view the full product warranty information.

CONDITIONS&EXCEPTIONS

The warranty covers original equipment at time of purchase only. The Wilbur Curtis Company, Inc., assumes no responsibility for substitute replace-

ment parts installed on Curtis equipment that have not been purchased from the

Wilbur Curtis Company, Inc. The Wilbur Curtis Company will not accept any responsibility if the following conditions are not met. The warranty

does not cover and is void under the following circumstances:

1) Improper operation of equipment: Theequipmentmustbeusedforitsdesignedandintendedpurposeandfunction.

2) Improper installation of equipment: Thisequipmentmustbeinstalledbyaprofessionaltechnicianandmustcomplywithalllocalelectrical,

mechanical and plumbing codes.

3) Improper voltage: Equipmentmustbeinstalledatthevoltagestatedontheserialplatesuppliedwiththisequipment.

4) Improper water supply: Thisincludes,butisnotlimitedto,excessiveorlowwaterpressure,andinadequateoructuatingwaterow

rate.

5) Adjustments and cleaning: Theresettingofsafetythermostatsandcircuitbreakers,programmingandtemperatureadjustmentsarethe

responsibilityoftheequipmentowner.Theownerisresponsibleforpropercleaningandregularmaintenanceofthisequipment.

6) Damaged in transit: Equipmentdamagedintransitistheresponsibilityofthefreightcompanyandaclaimshouldbemadewiththecar-

rier.

7) Abuse or neglect (including failure to periodically clean or remove lime accumulations): Manufacturerisnotresponsibleforvariation

inequipmentoperationduetoexcessivelimeorlocalwaterconditions.Theequipmentmustbemaintainedaccordingtothemanufacturer’s

recommendations.

8) Replacement of items subject to normal use and wear: Thisshallinclude,butisnotlimitedto,lightbulbs,sheardisks,“0”rings,gaskets,

siliconetube,canisterassemblies,whipperchambersandplates,mixingbowls,agitationassembliesandwhipperpropellers.

9) Repairs and/or Replacements aresubjecttoourdecisionthattheworkmanshiporpartswerefaultyandthedefectsshowedupundernormal

use.Alllaborshallbeperformedduringregularworkinghours.Overtimechargesaretheresponsibilityoftheowner.Chargesincurredby

delays,waitingtime,oroperatingrestrictionsthathindertheservicetechnician’sabilitytoperformserviceistheresponsibilityoftheowner

oftheequipment.Thisincludesinstitutionalandcorrectionalfacilities.TheWilburCurtisCompanywillallowupto100miles,roundtrip,per

in-warrantyservicecall.

RETURN MERCHANDISE AUTHORIZATION: AllclaimsunderthiswarrantymustbesubmittedtotheWilburCurtisCompanyTechnical

SupportDepartmentpriortoperforminganyrepairworkorreturnofthisequipmenttothefactory.Allreturnedequipmentmustberepackaged

properlyintheoriginalcarton.Nounitswillbeacceptediftheyaredamagedintransitduetoimproperpackaging.NO UNITS OR PARTS WILL

BE ACCEPTED WITHOUT A RETURN MERCHANDISE AUTHORIZATION (RMA). RMA NUMBER MUST BE MARKED ON THE CARTON

OR SHIPPING LABEL. All in-warranty service calls must be performed by an authorized service agent. Call the Wilbur Curtis Technical Sup-

portDepartmenttondanagentnearyou.

G4GEMTIF10B1000 1360100497 Curtis Gemini G4 Coffee Brewer

Product's Documents

Owners manual

Specifications

Gemini G4GEMTIF10B1000 1360100497 Questions and Answers

Related Products

G4GEMT10A1000 1360100496 Curtis Gemini G4 Coffee Brewer

G4GEMXN63A1000 1360101943 Curtis Gemini G4 GemX Narrow Coffee Brewer

GEM-120A-10 1360100015 Curtis Gemini Coffee Brewer

GEM-120A-63 1360100018 Curtis Gemini Coffee Brewer

GEM-12D-10 1360100020 Curtis Gemini Coffee Brewer

GEMTS19A1000 1360100206 Curtis Gemini G3 Coffee Brewer