Operating and installation
instructions
Refrigerators
It is essential to read the operating and installation instructions be-
fore setup, installation, and commissioning. This prevents both per-
sonal injury and damage to the appliance.
en-GB M.-Nr. 12 583 990
Contents
Warning and Safety instructions ............................................................................... 5
Sustainability and environmental protection.......................................................... 14
How to save energy.......................................................................................................
15
Installation...................................................................................................................... 16
Fastening the refrigeration appliance in the building-in niche.................................
16
Installation site ...............................................................................................................
16
Side-by-side installation................................................................................................
18
Ventilation........................................................................................................................
18
Connecting to the power supply..................................................................................
19
Aligning the refrigeration appliance .............................................................................
19
Mounting accessories supplied ...................................................................................
19
Knock sensor............................................................................................................. 19
Spacer plates............................................................................................................. 20
Levelling rails ............................................................................................................. 20
Cover strip ................................................................................................................. 21
Furniture door panel.......................................................................................................
21
Horizontal and vertical gaps.................................................................................... 21
Weight of the furniture door.................................................................................... 22
Building-in dimensions .................................................................................................
24
Installation in a tall unit/side view.......................................................................... 24
Connections and ventilation ................................................................................... 25
Electrical connection .....................................................................................................
26
Guide to the appliance................................................................................................. 27
Start display ....................................................................................................................
29
Using the appliance.................................................................................................. 29
Settings mode...................................................................................................... 30
Automatic door opening (ActiveDoor) ........................................................................
32
...via knocking signal ................................................................................................ 32
...via voice commands............................................................................................. 33
Adjusting the interior fittings ........................................................................................
34
Adjustable shelf with pivotable glass shelf (FlexiTray) ........................................ 34
Repositioning the door shelf with fine adjustment.............................................. 34
Moving the door shelf/bottle shelf......................................................................... 35
Moving the adjustable shelf/adjustable shelf with lighting ................................ 35
Moving the bottle rack............................................................................................. 35
Using the storage drawer (CompactCase) ........................................................... 35
Using the bottle rack in the dividing plate............................................................. 36
Removing and reinserting the organisation box................................................... 36
Inserting the adapters for the baking tray............................................................. 36
Moving the ActiveAirClean filter............................................................................ 36
Accessories supplied.....................................................................................................
37
Optional accessories .....................................................................................................
37
2
Contents
Switching on and off..................................................................................................... 38
Before using for the first time.......................................................................................
38
Connecting the refrigeration appliance ................................................................. 38
Filling and inserting the water container for the humidifier................................ 38
Switching the refrigeration appliance on ....................................................................
38
Switching off the refrigeration appliance ....................................................................
38
To note when switching off for longer periods of time........................................ 38
Requirements for networking ......................................................................................
39
Setting up networking for the first time ................................................................ 39
Performing Scan & Connect................................................................................... 39
Operation........................................................................................................................ 40
The correct temperature ...............................................................................................
40
Temperature display ................................................................................................. 40
Setting the temperature .......................................................................................... 40
Using Super cool ............................................................................................................
42
Storing food in the fridge zone .....................................................................................
42
Different storage zones............................................................................................ 42
Should food be stored loose or in packaging? ..................................................... 43
Storing food in the PerfectFresh Active zone.............................................................
43
PerfectFresh Active zone......................................................................................... 43
Humidity-controlled compartment ....................................................................... 44
Dry compartment ..................................................................................................... 47
Selecting further settings............................................................................................ 49
Explanation of the different settings............................................................................
49
Party mode ............................................................................................................ 49
Holiday mode ...................................................................................................... 49
Switching the lock function/ on.................................................................... 49
Sabbath mode....................................................................................................... 50
Automatic door opening (ActiveDoor) .............................................................. 51
Change the time until the door alarm is triggered when the door is
opened manually.......................................................................................................
54
Networking ................................................................................................................ 54
Changing the volume of the alarms and buzzers/ ..................................... 55
Adjusting the display brightness ....................................................................... 55
Switching off Demo mode ................................................................................... 56
Resetting the settings to their default settings ............................................. 56
Information............................................................................................................. 56
Charcoal filter change indicator......................................................................... 56
Cleaning mode.................................................................................................... 56
Cleaning and care ......................................................................................................... 58
Defrosting........................................................................................................................
58
Cleaning agents ..............................................................................................................
58
3
Contents
Preparing the refrigeration appliance for cleaning.....................................................
58
Cleaning the interior of the appliance .........................................................................
58
Cleaning accessories by hand or in the dishwasher .................................................
59
Removing and dismantling accessories for cleaning ................................................
59
Cleaning the door seal...................................................................................................
66
Cleaning the ventilation openings................................................................................
66
After cleaning ..................................................................................................................
66
Troubleshooting............................................................................................................. 67
Interior lighting................................................................................................................
75
Noises ..............................................................................................................................
77
Service............................................................................................................................. 79
Contact in the event of a fault......................................................................................
79
EPREL database .............................................................................................................
79
Warranty ..........................................................................................................................
79
Information..................................................................................................................... 80
EU Conformity declaration............................................................................................
80
UK Conformity declaration ...........................................................................................
80
Copyrights and licences ................................................................................................
81
4
Warning and Safety instructions
This refrigeration appliance complies with current safety require-
ments. Inappropriate use can, however, lead to personal injury and
material damage.
Please read the operating and installation instructions carefully be-
fore using the refrigeration appliance for the first time. They contain
important information on installation, safety, use and maintenance.
This is to protect yourself from injury, and from damaging your refri-
geration appliance.
In accordance with standard IEC60335-1, Miele expressly and
strongly advises that you read and follow all information provided
on installing the refrigeration appliance, as well as the warning and
safety notes.
Miele cannot be held liable for injury or damage caused by non-
compliance with these instructions.
Keep these operating and installation instructions in a safe place
and pass them on to any future owner.
Correct application
This refrigeration appliance is intended for use in the home and in
similar environments; for example:
–In shops, offices and similar work settings
–On agricultural estates
–By the guests in hotels, motels, bed and breakfasts, and other typ-
ical home settings.
This refrigeration appliance is not intended for outdoor use.
The refrigeration appliance is intended for domestic use only for
cooling and storing food and drink.
The refrigeration appliance is not suitable for freezing food.
Any other usage is not permitted.
This refrigeration appliance is not suitable for storing and keeping
cool medicines, blood plasma, laboratory preparations or similar sub-
stances or products that are subject to the Medical Device Directive.
Incorrect use of the refrigeration appliance for such purposes may
cause deterioration of the items stored. The refrigeration appliance is
also not suitable for use in areas where there is a risk of explosion.
Miele cannot be held liable for damage caused by improper or incor-
rect use or operation of the appliance.
5
Warning and Safety instructions
The appliance can only be used by people with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge,
if they are supervised whilst using it, or have been shown how to use
it in a safe way and recognise and understand the consequences of
incorrect operation.
Safety with children
Children under 8 years of age must be kept away from the refriger-
ation appliance unless they are constantly supervised.
Children 8 years and older may only use the appliance unsuper-
vised if they have been shown how to use it in a safe way and recog-
nise and understand the consequences of incorrect operation.
Children must not be allowed to clean or maintain the appliance
unsupervised.
Please supervise children in the vicinity of the appliance and do
not let them play with it.
Danger of suffocation. Whilst playing, children may become en-
tangled in packaging material (such as plastic wrapping) or pull the
packaging material over their head, presenting the risk of suffocation.
Keep packaging material away from children.
Technical safety
The coolant circuit has been checked for leaks. The refrigeration
appliance complies with statutory safety requirements and the ap-
propriate EU directives.
If the cooling circuit is damaged, refrigerant and oil can escape and ignite.
Warning: fire hazard/flammable materials. This symbol is on the
compressor and indicates flammable materials. Do not remove this
sticker.
6
Warning and Safety instructions
The refrigerant inside the appliance (details on the data plate) is en-
vironmentally friendly but flammable.
The use of this refrigerant does, however, sometimes lead to a slight
increase in the noise level of the appliance. In addition to the noise of
the compressor, you might be able to hear the refrigerant flowing
around the cooling circuit. Unfortunately, this cannot be avoided, but
it does not affect the performance of the refrigeration appliance.
When transporting and installing the refrigeration appliance, ensure
that no parts of the cooling circuit are damaged. Splashes of refriger-
ant can damage the eyes and leaking refrigerant can ignite.
In the event of damage:
- Avoid naked flames or anything which creates a spark.
- Disconnect the refrigeration appliance from the mains electricity
supply.
- Ventilate the room where the refrigeration appliance is located for
several minutes.
- Contact the Miele Customer Service Department.
The more refrigerant there is in a refrigeration appliance, the larger
the room it should be installed in. In the event of a leakage, if the ap-
pliance is in a small room, there is the danger of a combustible gas/
air mixture building up. For every 8g of refrigerant at least 1m
3
of
room space is required. The amount of refrigerant in the refrigeration
appliance is stated on the data plate inside the appliance.
If the ventilation cross-sections are covered or blocked, a com-
bustible gas/air mixture can form if the cooling circuit is damaged. It
is essential to observe the required ventilation cross-sections. The
ventilation cross-sections must not be covered or blocked in any way.
To avoid the risk of damage to the appliance, make sure that the
connection data (fuse rating, frequency and voltage) on the data plate
corresponds to the household supply.
Check that this is the case before connecting the appliance. Consult
a qualified electrician if in any doubt.
The electrical safety of this appliance can only be guaranteed when
correctly earthed. It is essential that this standard safety requirement
is met. If in any doubt please have the electrical installation tested by
a qualified electrician.
7
Warning and Safety instructions
Temporary or permanent operation on an autonomous power sup-
ply system or a power supply system that is not synchronised with
the mains power supply (e.g. island networks, back-up systems) is
possible. A prerequisite for operation is that the power supply system
complies with the specifications of EN50160 or an equivalent stand-
ard.
The function and operation of the protective measures provided in
the domestic electrical installation and in this Miele product must
also be maintained in isolated operation or in operation that is not
synchronised with the mains power supply, or these measures must
be replaced by equivalent measures in the installation. As described,
for example, in the current version of BS OHSAS 18001–2 ISO
45001.
The socket must not be concealed behind the refrigeration appli-
ance and must be easily accessible so that the appliance can be
quickly disconnected from the electrical supply in case of an emer-
gency.
If the mains connection cable is damaged, disconnect the refriger-
ation appliance from the power supply immediately. Contact the
Miele Customer Service Department.
If the mains connection cable is damaged, it must only be replaced
with a specific mains connection cable of the same type (available
from the Miele online shop or Miele Customer Service). For safety
reasons, such replacement may only be carried out by a qualified
specialist or Miele Customer Service.
Do not connect the appliance to the mains electrical supply by a
multi-socket adapter or extension lead. These are a fire hazard and do
not guarantee the required safety of the appliance.
If moisture gets into electrical components or into the mains con-
nection cable, it could cause a short circuit. Therefore, do not operate
this refrigeration appliance in areas which are exposed to moisture
(e.g in a garage or utility room).
This appliance must not be used in a non-stationary location (e.g.
on a ship).
Do not use a damaged appliance. It could be dangerous. Check the
appliance for visible signs of damage.
For safety reasons, this appliance may only be used after it has
been built in.
8
Warning and Safety instructions
The appliance must be isolated from the electricity supply during
installation, maintenance and repair work. It is only completely isol-
ated from the power supply when:
- the mains fuses are switched off, or
- the screw-out fuse is removed (where applicable), or
- the mains cable has been unplugged. Pull on the plug and not the
cable when disconnecting it from the power supply.
Unauthorised installation, maintenance or repairs could result in
unforeseen dangers for the user, for which the manufacturer cannot
accept liability.
Installation, maintenance or repairs must only be carried out by a
qualified specialist or Miele Customer Service.
The manufacturer’s warranty will be invalidated if the refrigeration
appliance is not repaired by a qualified specialist or Miele Customer
Service.
If defective safety-relevant components are replaced, Miele can
only guarantee full compliance with safety requirements if genuine
Miele replacement parts are used.
This refrigeration appliance is fitted with a special lamp to cope
with particular conditions (e.g. temperature, moisture, chemical res-
istance, abrasion resistance and vibration). This lamp must only be
used for the purpose for which it is intended. The lamp is not suitable
for room lighting. Replacement lamps may only be fitted by a quali-
fied specialist or by Miele Customer Service. This refrigeration appli-
ance contains several light sources with at least energy efficiency
classF.
Proper installation
When installing the refrigeration appliance, it is a mandatory re-
quirement to follow the operating instructions.
Install the refrigeration appliance in accordance with the installa-
tion instructions.
Change the door hinging (if necessary) as described in the installa-
tion instructions.
Always wear protective gloves when transporting and installing the
refrigeration appliance and when changing the door hinging.
Only install the refrigeration appliance in a solid, rectangular and
level housing unit, positioned on an even and level floor.
9
Warning and Safety instructions
The refrigeration appliance is heavy and can tip forwards when the
appliance door(s) is/are open:
- At least 2people are required to transport or move the refrigera-
tion appliance.
- At least 2people are required to change the door hinging of the re-
frigeration appliance.
- At least 2people are required to install the refrigeration appliance.
- Never leave the refrigeration appliance unattended while it is being
installed.
- It is essential that you secure the refrigeration appliance in the
niche using the enclosed retaining and fastening parts (installation
instructions).
Correct use
This refrigeration appliance is designed for use within specific am-
bient temperatures (climate range). Do not use in ambient temperat-
ures for which it is not designed. The climate range is stated on the
data plate in the interior cabinet of the refrigeration appliance. A
lower ambient temperature will cause the compressor to switch off
for longer periods, meaning that the refrigeration appliance is unable
to maintain the required temperature.
The ventilation cross-sections must not be covered or blocked in
any way. This can impair the proper ventilation of the appliance, in-
crease the energy consumption and cause damage to the compon-
ents.
Risk of damage due to greasy or oily foods. If the refrigeration ap-
pliance or the appliance door is used for storing food which contains
fat or oil, make sure that it does not come into contact with plastic
components. Any spillages of oil or fat could cause stress cracks to
the plastic and cause it to break or split.
Risk of fire and explosion due to flammable mixes of gases. Do not
store explosive materials in the refrigeration appliance or any
products containing propellants (e.g. spray cans). Electrical compon-
ents can cause flammable mixes of gases to ignite. The spray cans in
question can be identified by the contents printed on the can or by a
flame symbol. Electrical components can cause escaping gases to ig-
nite.
10
Warning and Safety instructions
Danger of explosion. Do not operate any electrical equipment (e.g.
an electric ice-cream maker) inside the refrigeration appliance. This
can cause sparking and explosion.
Observe the manufacturer's “use-by” dates and storage instruc-
tions given on food to avoid the risk of food poisoning. Storage times
will depend on several factors, including the freshness and quality of
the food, as well as the temperature at which it is stored.
Accessories and spare parts
Miele assumes no liability for the use of accessories that are not
genuine Miele accessories. Miele is not liable for warranty, guarantee
and/or product liability claims if damage or defects are due to the use
or installation of accessories that do not originate from Miele or have
not been approved by Miele.
Miele original spare parts are kept in stock for at least 10years and
up to 15years after discontinuation of your refrigeration appliance.
Cleaning and care
Do not use any oils or grease on the door seals, as these will cause
the seals to deteriorate and become porous with time.
Do not use a steam cleaning appliance to clean or defrost this ap-
pliance.
Steam could reach electrical components and cause a short circuit.
Sharp edged or pointed objects will damage the evaporator, caus-
ing irreversible damage to the appliance. Do not use sharp edged or
pointed objects to
- remove frost and ice,
- separate frozen food or remove ice trays.
Do not place electric heaters or candles in the appliance to defrost
it. These can damage the plastic parts.
Do not use defrosting sprays or de-icers. Defrosting sprays and
de-icers can contain substances which could damage the plastic
parts or which might cause a build-up of explosive gases and pose a
danger to health.
Transport
To avoid damage to the refrigeration appliance, always transport it
upright and in its packaging.
11
Warning and Safety instructions
Danger of injury and damage to the appliance. The refrigeration ap-
pliance is very heavy and must be transported by two people.
Disposal of your old appliance
Children playing could become trapped in the refrigeration appli-
ance and could suffocate.
- Remove the appliance door(s).
- Remove the drawers.
- Leave the shelves in the refrigeration appliance so that children
cannot climb inside.
- If your old refrigeration appliance has a door lock, destroy it. This
will prevent the risk of children playing accidentally locking them-
selves in the appliance and endangering their lives.
Risk of electric shock!
- Cut the plug off the mains connection cable.
- Cut the mains connection cable off the old appliance.
Dispose of the plug and mains connection cable separately from the
old appliance.
During and after disposal, make sure that the refrigeration appli-
ance is not placed near petrol or other flammable gases and liquids.
Risk of fire due to escaping oil or refrigerant.
The refrigerant and oil inside the appliance are flammable. In high
enough concentrations, escaping refrigerant or oil can ignite if they
come into contact with an external heat source.
During disposal, make sure that the cooling circuit is not damaged.
This prevents refrigerant and oil escaping in an uncontrolled manner
(see the data plate for details of the refrigerant).
Splashes of coolant can damage the eyes. Be careful not to dam-
age any part of the pipework whilst awaiting disposal, e.g. by
- puncturing the coolant channels in the condenser,
- bending any pipework, or
- scratching the surface coating.
Symbol on the compressor (depending on model)
This information is only relevant for recycling. There is no risk during normal opera-
tion.
12
Warning and Safety instructions
The oil in the compressor can be fatal if swallowed or if it penet-
rates the airways.
13
Sustainability and environmental protection
Disposing of the packaging ma-
terial
The packaging material is used for hand-
ling and protects the appliance from
transport damage.
Recycling the packaging material re-
duces the use of raw materials. Use ma-
terial-specific collection points for valu-
able materials and take advantage of re-
turn options. Your Miele dealer will take
the packaging material away.
Disposing of your old appliance
Electrical and electronic appliances con-
tain many valuable materials. They also
contain certain materials, compounds
and components which were essential
for their correct functioning and safety.
These could be hazardous to human
health and to the environment if dis-
posed of with household waste or if
handled incorrectly. Please do not,
therefore, dispose of your old appliance
with household waste.
Take care not to damage your refrigera-
tion appliance before or during disposal
in an authorised, environmentally
friendly manner.
This is to ensure that refrigerant in the
cooling circuit and oil in the compressor
is contained, and will not leak into the
environment.
Instead, please make use of officially
designated collection and disposal
points to dispose of and recycle elec-
trical and electronic appliances in your
local community, with your dealer or
with Miele, free of charge. By law, you
are solely responsible for deleting any
personal data from the old appliance
prior to disposal. You are legally obliged
to remove any old batteries which are
not securely enclosed by the appliance
and to remove any lamps without des-
troying them, where this is possible.
These must be taken to a suitable col-
lection point where they can be handed
in free of charge. Please ensure that
your old appliance poses no risk to chil-
dren while being stored for disposal.
14
Sustainability and environmental protection
How to save energy...
How to save energy:
Installation site The refrigeration appliance has to cool more often at higher am-
bient temperatures and consumes more energy in the process.
Therefore, you should:
- Install the refrigeration appliance in a well-ventilated room.
- Do not install the refrigeration appliance near to a heat source
(heater element, cooker).
- Protect the refrigeration appliance from direct sunlight.
- Ensure an ideal ambient temperature of 20°C.
- Clean the ventilation gaps on a regular basis to remove any
dust.
Temperature
setting
The colder the temperature, the higher the energy consumption.
The following settings are recommended:
- 4 to 5°C in the refrigerator section.
- PerfectFresh Active zone just above 0°C.
Use Energy consumption is increased by heat input and impeded air
circulation. Therefore:
- Only open the appliance door/appliance doors when necessary
and for as short a time as possible. Arrange the food in such a
way that makes it easy to find in the appliance.
- Always close the appliance door/appliance doors properly after
opening.
- Allow hot food and drinks to cool down before placing them in
the refrigeration appliance.
- Store food well packaged or covered.
- Do not overfill the compartments to allow air to circulate.
- Place frozen food in the fridge zone to defrost.
- Keep drawers and shelves arranged as they were when the ap-
pliance was delivered.
15
Installation
Carry out the installation in ac-
cordance with the installation instruc-
tions (see QR code).
M.-Nr. 12544730
Ordering printed installation instruc-
tions
You can order printed installation in-
structions free of charge from Miele.
All the contact information you need for
Miele can be found at the end of this
document. Quote the model identifier
and the serial number from the data
plate when placing your order.
Fastening the refrigeration ap-
pliance in the building-in niche
Risk of damage and danger of in-
jury due to the refrigeration appliance
tipping over.
This refrigeration appliance is very
heavy and can tip forwards when the
appliance door is open.
Keep the appliance door(s) closed
until the refrigeration appliance has
been built in.
It is essential that you secure the re-
frigeration appliance in the niche us-
ing the enclosed retaining and fasten-
ing parts in accordance with the in-
stallation instructions.
Installation site
Fire risk and risk of damage from
appliances which give off heat.
Appliances which give off heat can
catch fire and set fire to the refrigera-
tion appliance.
The mains connection cable must not
come into contact with heat sources.
This refrigeration appliance must not
be installed underneath a hob.
Fire risk and danger of damage
from open flames.
Open flames can set fire to the refri-
geration appliance.
Keep open flames (e.g. a candle)
away from the refrigeration appli-
ance.
16
Installation
Risk of fire and damage due to
improper installation.
If the mains plug and mains connec-
tion cables touch the back of the re-
frigeration appliance, they may be
damaged by vibrations and cause a
short circuit.
Mains plugs or mains connection
cables must not touch the refrigera-
tion appliance.
Mains connection cables must not
be trapped or damaged.
Do not connect any other appliances
to sockets located directly behind
this refrigeration appliance.
Do not place or operate multi-socket
adapters, distributor strips or other
electronic devices (such as halogen
transformers) behind the appliance.
This appliance should be installed in a
dry, well-ventilated room.
Only install the refrigeration appliance in
a solid, rectangular and level housing
unit, positioned on an even and level
floor.
Risk of damage due to high hu-
midity.
In environments with high humidity,
condensation can build up on ex-
ternal refrigeration appliance panels.
This condensation can cause corro-
sion on external appliance panels.
Install the refrigeration appliance in a
dry and/or air-conditioned room with
sufficient ventilation.
After installation, please make sure
that the appliance door/appliance
doors closes/close properly and the
refrigeration appliance is installed in
accordance with these installation in-
structions. It is essential to comply
with the specified ventilation cross-
sections.
When deciding on the installation site,
please bear in mind that your refrigera-
tion appliance will consume more en-
ergy if installed near to a heater, a
cooker or another appliance that gives
off heat. Avoid direct sunlight. Higher
ambient temperatures increase energy
consumption as the compressor runs
for longer.
17
Installation
Climate range
This refrigeration appliance is designed
for use within specific ambient temper-
atures (climate range). Do not use in
ambient temperatures for which it is not
designed. The climate range is stated on
the data plate in the interior cabinet of
the refrigeration appliance.
Climate range Ambient temper-
ature
SN 10to32°C
N 16to32°C
ST 16to38°C
T 16to43°C
SN-ST 10to38°C
SN-T 10to43°C
A lower ambient temperature leads to
the compressor switching off for longer
periods. This can cause the internal
temperature in the refrigeration appli-
ance to rise with the risk of food deteri-
orating and going off.
Side-by-side installation
Risk of damage due to condensa-
tion on external appliance panels.
In environments with high humidity
and a lack of ventilation, condensa-
tion can build up on external appli-
ance panels, which can cause corro-
sion.
Do not place refrigeration appliances
directly next to or on top of one an-
other if the refrigeration appliance is
not approved for this.
Your refrigeration appliance can possibly
be installed alongside another refrigera-
tion appliance with an integrated heat-
ing unit if each appliance is built into a
separate niche.
Tip: Please contact your dealer for spe-
cific information about which combina-
tions will work with your refrigeration
appliance.
Ventilation
Fire risk and risk of damage due
to inadequate ventilation.
If the refrigeration appliance is not
ventilated sufficiently, the com-
pressor will run more frequently and
for longer periods. This causes in-
creased energy consumption and an
increased compressor operating tem-
perature, which can result in damage
to the refrigeration appliance.
Please ensure that there is adequate
ventilation around the refrigeration
appliance:
It is essential to observe the required
ventilation cross-sections.
The ventilation cross-sections must
not be covered or blocked in any way.
Clean the ventilation areas regularly
to remove dust and dirt.
Air at the back of the refrigeration appli-
ance gets warm. The appliance housing
unit must therefore be constructed to
allow sufficient space for ventilation
(see “Installation dimensions” and the
installation instructions).
18
Installation
Connecting to the power supply
Risk of damage due to automat-
ically opening door. Damage to the
drive unit of the appliance door.
If the refrigeration appliance is not
yet fully installed in the kitchen unit,
but you have already connected it to
the power supply, the door may open
unexpectedly. If the appliance door is
too close to the niche floor, the door
may drag on the floor and damage
parts of the drive unit.
Do not insert the mains plug into the
socket until the refrigeration appli-
ance has been installed correctly.
- The socket must be easily accessible
in an emergency, not concealed be-
hind the appliance.
- The mains plug and mains connection
cable must not touch the rear of the
refrigeration appliance as they could
be damaged by vibrations from the
appliance.
- Other appliances must also not be
plugged into a socket located directly
behind the refrigeration appliance.
- When installing the refrigeration appli-
ance, make sure that the mains con-
nection cable does not get trapped or
damaged.
- Do not position or operate multi-
socket adapters, distributor strips or
other electronic devices (e.g. halogen
transformers) at the rear of the appli-
ance.
Aligning the refrigeration appli-
ance
The refrigeration appliance must be
aligned exactly vertically in the niche.
This is the only way to ensure that the
appliance door’s automatic opening mo-
tion is smooth.
It is not possible to change the door
hinging as the refrigeration appliance
features automatic door opening.
Mounting accessories supplied
Install the refrigeration appliance in
accordance with the installation in-
structions.
Knock sensor
19
Installation
- When installing the knock sensor, en-
sure that the connecting cable is not
damaged.
- Gluing the knock sensor to the fur-
niture front optimises the transmis-
sion of the knocking signal. Before in-
stallation, it is essential to remove the
protective foil from the contact sur-
face of the sensor.
- Permanently securing the knock
sensor with the screws that are in-
cluded helps it function more reliably.
The sensitivity of the knock sensor is set
using a slide control (see “Automatic
door opening (ActiveDoor)” in “Guide to
the appliance”).
Spacer plates
Risk of damage caused by the
door dragging on the floor. Damage
to the drive unit of the appliance
door.
If the spacer plates included are not
installed in the niche, the distance
from the appliance door to the niche
floor will be too short.
Install the spacer plates on the niche
floor.
Always maintain a distance of
300mm from the front edge of the
niche.
The way in which the spacer plates are
installed has an impact on the func-
tion.
The distance from the appliance door
to the niche floor is increased.
Levelling rails
These are enclosed from a niche
height of 1400mm.
The noise level is reduced when they are
installed.
1
2
2
1 – installation handle, 2 – levelling rails
Slide the two levelling rails underneath
the refrigeration appliance using the in-
stallation handle (see installation in-
structions).
20
Installation
Cover strip
For installation in a niche with a niche
height of less than 1777mm but at
least 1772mm.
If the cover strip does not fit between
the refrigeration appliance and the niche
ceiling, it does not need to be fitted.
Furniture door panel
Horizontal and vertical gaps
To prevent the appliance door from
being struck from the side or becom-
ing jammed whilst the door is open-
ing automatically, a gap of at least
4mm must be maintained.
Depending on the style of kitchen fur-
niture, the thickness and edge radius of
the furniture door and the gap that runs
around the door, vertically and horizont-
ally, are specified.
- Horizontal gap
The gap between the furniture door and
the housing unit door above or below it
must be at least 4mm.
21
Installation
- Vertical gap
If the joint gap between the refrigera-
tion appliance furniture door panel
and adjoining kitchen furniture front
or wall on the hinged side is too
small, the refrigeration appliance
door may collide with it when
opened.
Check the furniture door panel for
any collisions.
Determine the required joint gap
width based on the thickness and
edge radius of the furniture door
panel.
This must be taken into consideration
when planning your kitchen and when
replacing an old refrigeration appliance
with a new one to ensure the installa-
tion conditions required are met.
Furniture
door
thickness
A [mm]
Gap X [mm]
for different
edge radii B
R0 R1.2 R2 R3
≥16–19 min. 4
20 5 4 4 4
21 5.5 5 4.5 4
22 6.5 6 5.5 5
Adjoining kitchen furniture front
A=Furniture front thickness
B=Edge radius
X=Gap
Adjoining side wall
A=Furniture front thickness
B=Edge radius
X=Gap
Tip: Fit a spacer between the housing
unit carcase and the side wall. This way
you will get a sufficiently wide gap.
Weight of the furniture door
If the furniture door panel is too
heavy, this can cause damage.
Fitting a furniture door panel which is
heavier than the maximum permitted
weight could damage the hinges. This
can cause subsequent functional
problems.
The maximum permissible weight of the
furniture door is:
22
Installation
Refrigeration appliance kg
K 7797 ... 26
23
Installation
*INSTALLATION*
Building-in dimensions
Installation in a tall unit/side view
Before installation, ensure the housing unit dimensions are the correct size. The
refrigeration appliance will function correctly if the specified ventilation cross-sec-
tions are maintained.
All dimensions are given in mm.
* The declared energy consumption was calculated in a 560mm deep niche. The
refrigeration appliance is fully functional in a 550mm niche but the energy con-
sumption will be slightly higher.
24
Installation
*INSTALLATION*
Connections and ventilation
Before installation, ensure the housing unit dimensions are the correct size. The
refrigeration appliance will function correctly if the specified ventilation cross-sec-
tions are maintained.
All dimensions are given in mm.
a
Front view
b
Mains connection cable, length = 2200mm
A longer mains connection cable is available to order from the Miele Customer
Service Department.
c
Ventilation cross-section min. 200 cm
2
d
Ventilation
e
No connection sockets in this area
25
Installation
*INSTALLATION*
Electrical connection
The refrigeration appliance must only be
connected to an earthed socket using
the mains connection cable supplied.
The socket must be easily accessible
after the refrigeration appliance has
been installed. If the socket is not easily
accessible, ensure that a suitable
means of disconnection is provided on
the installation side for each pole.
Risk of fire from overheating.
Connecting the refrigeration appli-
ance to a multi-socket plug adapter
or to an extension lead can overload
the cable.
For safety reasons, do not use an ex-
tension lead or multi-socket adapter.
The electrical installation must comply
with VDE0100 requirements.
For safety reasons, we recommend us-
ing a type residual current device
(RCD) in the assigned electrical installa-
tion for connecting the refrigeration ap-
pliance.
If the mains connection cable is dam-
aged, it must only be replaced with a
specific mains connection cable of the
same type (available from the Miele
Customer Service Department). For
safety reasons, such replacement may
only be carried out by a qualified spe-
cialist or the Miele Customer Service
Department.
These operating instructions and the
data plate indicate the nominal power
consumption and the appropriate fuse
rating. Compare this information with
the data of the on-site electrical con-
nection. If in any doubt, consult a quali-
fied electrician.
Temporary or permanent operation on
an autonomous power supply system or
a power supply system that is not syn-
chronised with the mains power supply
(e.g. island networks, back-up systems)
is possible. A prerequisite for operation
is that the power supply system com-
plies with the specifications of
EN50160 or an equivalent standard.
The function and operation of the pro-
tective measures provided in the do-
mestic electrical installation and in this
Miele product must also be maintained
in isolated operation or in operation that
is not synchronised with the mains
power supply, or these measures must
be replaced by equivalent measures in
the installation. As described, for ex-
ample, in the current version of VDE-
AR-E2510-2.
Connecting the refrigeration appliance
Insert the plug connector into the
socket at the back of the refrigeration
appliance.
Make sure that the plug connector has
clicked into position correctly.
Insert the plug of the refrigeration ap-
pliance into the socket.
The refrigeration appliance is now con-
nected to the electricity supply.
26
Guide to the appliance
This image shows an example of an appliance model with right-hand hinging.
27
Guide to the appliance
a
Display
b
Fan with lighting
c
Dry rear panel to prevent condensate
d
Adjustable shelf with pivotable glass shelf (FlexiTray)
e
Egg tray
Clip the egg tray onto the rear edge of the door shelf.
f
Door shelf with fine adjustment:
You can adjust the height of the door shelf individually when loaded to create
space for tall bottles.
g
Storage drawer (CompactCase) for storing small containers
h
Adjustable shelf with lighting (FlexiLight 2.0)
i
Flexible bottle rack
j
Space for a baking tray (ComfortSize)
k
Bottle shelf with bottle holder:
You can move the bottle holder to the right or left to create space for drinks car-
tons.
l
Dividing plate with bottle rack,
water container and humidifier:
Fruit and vegetables are humidified every time the door is opened and approx.
every 90minutes.
m
Cover for setting the moisture level in the humidity-controlled compartment
n
Slide control for setting the sensitivity of the knock sensor (ActiveDoor)
o
Humidity-controlled compartment for fruit and vegetables (PerfectFresh Active
zone)
p
Organisation box:
Store food that is prone to squashing, e.g. berries, here.
q
Condensate channel and condensate drain hole:
Precipitated condensate runs off and evaporates automatically.
r
Dry compartment with low temperature for food which goes off quickly
(PerfectFresh Active zone)
28
Guide to the appliance
Start display
The display can be scratched by pointed or sharp objects, e.g. pens.
Only touch the display with your fingertips.
It is possible that the display will not react to finger contact if your fingers are
cold.
5
°C
1
2
3
4
a
Temperature display for fridge zone
b
Settings mode
sensor control for adjusting various settings in Settings mode
c
Display for connection status
(only visible if the network has been set up)
d
Demo mode display
(only visible when the Demo mode function has been switched on)
Using the appliance
Touch the area/symbol you want on the start display.
Swipe left or right across the display until the value/symbol you want is shown in
the middle.
Tap on the option you want on the display to confirm.
The selected value/symbol will light up orange (except for a few exceptions).
To leave the Settings level, tap on or OK.
29
Guide to the appliance
Settings mode
In Settings mode, you can select the following appliance functions and alter their
settings to some extent:
Symbol Function Factory
default
Switch the Party mode function on or off
(see “Selecting further settings”)
Off
Switch the Holiday mode function on or off
(see “Selecting further settings”)
Off
/ Switching the lock function on or off
(see “Selecting further settings”)
(off)
Switching off the refrigeration appliance ––
Switch the Sabbath mode function on or off
(see “Selecting further settings”)
Off
Call up the Sabbath mode version ––
A
Configure or deactivate the automatic door opening
(ActiveDoor) function.
(See “Selecting additional settings”)
Activate/deactivate ActiveDoor
(only appears when ActiveDoor is activated, see “Select-
ing further settings”)
Change the set door opening angle (only appears if a
door opening angle has already been set, see “Selecting
further settings”)
Change the time until the door alarm is triggered when
the door is opened manually (see “Selecting further set-
tings”)
1:00
Adjust the temperature level in the PerfectFreshActive
zone
(see “The correct temperature”)
5
Switching the humidifier on or off or adjusting its intens-
ity (see “Storing food in the PerfectFresh Active zone”)
Off
30
Guide to the appliance
Set up the Miele@home function for the first time,
activate and deactivate WiFi
or reset the network configuration
(see “Selecting further settings”)
App
/
Switch the keypad tone on or off On
/ Change the volume of the alarms and buzzers or switch
them off entirely
(see “Selecting further settings”)
On
/level5
Change the display brightness
(see “Selecting further settings”)
Level4
°C / °F Change the temperature unit
(°Celsius or °Fahrenheit)
°C
Switch the Demo mode function off
(only visible when switched on)
(see “Selecting further settings”)
Off
Reset to default settings
(see “Selecting further settings”)
––
Call up information (model identifier and serial number)
about your refrigeration appliance
(see “Selecting further settings”)
––
Switch on the reminder to change the
charcoal filter (see “Optional accessories”)
(see “Selecting further settings”)
Off
Switch Cleaning mode on or off
(see “Cleaning and care”)
Off
31
Guide to the appliance
Automatic door opening (Act-
iveDoor)
Risk of injury during automatic
opening and closing of the appliance
door
Body parts such as fingers can be-
come jammed in the area of the door
opening range and in the door hinge
area.
Leave the area of the door opening
range clear.
Do not reach into the door hinge area
or inside the refrigeration appliance
with your hand while the door is clos-
ing.
Do not block the door.
Risk of damage caused by
manual movement of the appliance
door when automatic door opening is
activated. Damage to the drive unit of
the appliance door.
If you open or close the appliance
door by using your hand against the
automatic door movement, the drive
unit and the door hinge will be dam-
aged.
Do not move the appliance door by
using your hand against the auto-
matic door movement.
Risk of damage while the appli-
ance door is closing automatically
Drawers or telescopic runners that
are pulled out can be damaged (de-
pending on the model).
Push in drawers fully.
Push in telescopic runners fully after
removing a drawer.
This function must be activated and
configured in Settings mode (see
“Selecting further settings – Automatic
door opening (ActiveDoor)
A
”).
During automatic door movement,
A
flashes in the display and a buzzer
sounds.
When automatic door opening is activ-
ated, you can open the appliance door
using the knocking signal or voice com-
mands.
The appliance door can be opened
manually if you decide not to activate
ActiveDoor or if you deactivate it.
When the function is activated, the re-
frigeration appliance runs at a higher
power level. This means that the
movement noises may be louder. The
energy consumption will be higher.
...via knocking signal
Knock twice on the outside or inside of
the door to open or close it.
The sensitivity of the knocking signal
can be changed at any time.
32
Guide to the appliance
Sensitivity of the knock sensor
A slide control is used to set the sensit-
ivity of the knock sensor. This slide con-
trol is located on the hinge-side outer
edge in the lower third of the door (see
“Guide to the appliance”).
Settings
Switch
setting
Meaning
Top
(3 dots)
High sensitivity, light
knocking sufficient.
Middle
(2 dots)
Medium sensitivity, slightly
heavy knocking required.
This is the default setting.
Bottom
(1 dot)
Low sensitivity, heavy
knocking required.
...via voice commands
In addition to the knocking signal, you
can also open and close the appliance
door via voice commands.
To do this, proceed as described below:
Activate and configure ActiveDoor
(see “Selecting further settings”, sec-
tion “1.Activate and configure Active-
Door for the first time”).
For information on the following set-
tings, see “Miele@home” in “Select-
ing further settings”.
Install the Mieleapp on your smart-
phone.
Establish a WiFi connection to your
refrigeration appliance.
Register your refrigeration appliance
in the Mieleapp by following the in-
structions in the app.
If you do not already have one, install
a suitable voice-activated assistant
from a provider.
Connect to the voice assistant via the
Miele app. To do this, follow the in-
structions in the app.
33
Guide to the appliance
Adjusting the interior fittings
Adjustable shelf with pivotable glass
shelf (FlexiTray)
Risk of damage caused by load-
ing too much food and not distribut-
ing items evenly.
Loading too much food and not dis-
tributing items evenly can damage
the pivotable glass shelf.
Do not exceed the maximum load
size of 8kg. Arrange food items
evenly across the full surface of the
shelf.
The pivotable glass shelf can be turned
180° clockwise, improving access to the
food placed at the back.
Danger of injury from dropping
the glass shelf.
The pivotable glass shelf can come
out when removing the adjustable
shelf, causing the glass shelf to drop
out of the tray and break.
Keep hold of the pivotable glass shelf
when removing the adjustable shelf.
You can move the adjustable shelf with
pivotable glass shelf as you wish.
Repositioning the door shelf with fine
adjustment
Only move the door/bottle shelves in
the appliance door when they are
empty.
Take hold of the sides of the door
shelf with both hands so that you are
touching each of the grey buttons un-
derneath it.
Press the grey buttons at the same
time and slide the door shelf up and
off the guide rails.
Remove the guide rail from the lugs
and move it to the desired position.
Move the second guide rail parallel to
the first rail.
Push the shelf down onto the guide
rails.
34
Guide to the appliance
Moving the door shelf/bottle shelf
Only move the door/bottle shelves in
the appliance door when they are
empty.
Push the door/bottle shelves up-
wards, then remove them by pulling
them forwards.
Replace the door/bottle shelves at
the required height.
Moving the adjustable shelf/ad-
justable shelf with lighting
Raise the shelf slightly at the front
and pull it forwards a little.
Lift it until the notches at the side are
in line with the shelf supports. The
shelf can then be raised or lowered to
the required level.
Push the shelf in.
Make sure that the shelf with lighting
clicks into position.
Stoppers prevent the shelves from be-
ing dislodged by mistake.
Moving the bottle rack
The bottle rack can be placed at differ-
ent positions in the refrigeration appli-
ance.
Raise the bottle rack slightly at the
front, and pull it forwards a little until
the notch at the side is in line with the
shelf support. It can then be raised or
lowered to the required level.
The rear rail must face upwards to pre-
vent bottles from touching the back of
the appliance.
Stoppers prevent the bottle rack from
being dislodged by mistake.
Using the storage drawer (Compact-
Case)
The drawer can be moved down slightly
to accommodate larger packets.
Pull the drawer out as far as it will go.
Tilt the drawer slightly upwards and
remove it.
35
Guide to the appliance
Now insert the drawer into the lower
holder in the support as required.
Using the bottle rack in the dividing
plate
Remove the glass shelf at the back of
the dividing plate and keep it in a safe
place.
Place the bottles as far back as pos-
sible with the bases at the back of the
appliance.
Tip: If the bottles hang over the edge of
the bottle rack, adjust the bottom bottle
shelf in the door by moving it upwards.
Removing and reinserting the organ-
isation box
Lift the organisation box at the rear
first when you want to remove it.
To reinsert the organisation box in the
drawer, place the front section in first.
Inserting the adapters for the baking
tray
The baking tray can be no more than
466mm wide, 386mm deep and
50mm high.
Snap the adapters into place on the
lowermost shelf supports on the side
walls of the fridge zone.
Open the appliance door as far as it
will go.
Place the baking tray on the adapters
in the fridge zone and slide it in as far
as it will go.
Moving the ActiveAirClean filter
The holder for the ActiveAirClean filters
sits on a protective strip at the back of
the shelf.
To move the ActiveAirClean filter, pull
it upwards to remove it from the pro-
tective strip.
Then pull the protective strip off the
shelf.
Refit it on the shelf you wish to use it
on.
36
Guide to the appliance
Refit the ActiveAirClean filter on the
protective strip.
Accessories supplied
Adjustable shelf with pivotable glass
shelf (FlexiTray)
Egg tray
Adapters for the baking tray
Organisation box
Flexible bottle rack
Optional accessories
A range of useful Miele accessories and
care products are available for your ap-
pliance.
Products specially tailored to your refri-
geration appliance – such as appliance
care products and accessories – are
available from the Miele online shop,
from Miele Customer Service or from
your Miele specialist dealer.
You can access the Miele online shop
via the following QR code:
37
Switching on and off
Before using for the first time
Remove all packaging material and
protective foil.
Clean the inside of the appliance and
the accessories.
Connecting the refrigeration appliance
Connect the refrigeration appliance to
the electricity supply as described in
“Electrical connection”.
Miele will then appear on the appliance
display, followed by .
Filling and inserting the water con-
tainer for the humidifier
Fill the water container for the humid-
ifier with fresh drinking water (see
“Storing food in the PerfectFresh Act-
ive zone – Humidity-controlled com-
partment”).
Place the water container in the divid-
ing plate between the refrigerator
section and PerfectFresh Active zone
(see “Storing food in the PerfectFresh
Active zone – Humidity-controlled
compartment”).
Switching the refrigeration ap-
pliance on
Open the appliance door.
Tap on the display.
The refrigeration appliance will start to
cool and the interior lighting will come
on when the appliance door is opened.
The refrigeration appliance will adjust to
the preset temperature.
To enable the temperature to get suf-
ficiently cold inside the refrigeration
appliance, allow the appliance to run
for a few hours before placing food in
it. Do not place food in the refrigera-
tion appliance until it has reached the
preset temperature.
Switching off the refrigeration
appliance
Touch the temperature display on the
display.
Swipe right until is shown in the
middle.
Tap.
The cooling and interior lighting are
switched off.
will appear in the display.
Please note: The refrigeration appli-
ance is not disconnected from the
mains power supply when it is
switched off.
To note when switching off for longer
periods of time
If, during a long absence, the refriger-
ation appliance is switched off but
not cleaned and the door is left shut,
there is a danger of mould building up
inside the appliance.
It is essential to clean the refrigera-
tion appliance.
If the refrigeration appliance is not going
to be used for a longer period of time,
observe the following:
Switch the refrigeration appliance off.
Switch off at the wall and withdraw
the plug from the socket, or discon-
nect the fuse.
38
Switching on and off
Take the water container for the hu-
midifier out of the appliance, empty it,
then clean and dry it.
Clean the refrigeration appliance and
leave the door ajar to air the appliance
and avoid odours building up inside.
Requirements for networking
Note the following requirements for net-
working:
1. A home network is available at the
installation site.
Have the WiFi password ready.
2. The Miele app is available on a mo-
bile device.
3. You have a user account in the Miele
app.
Miele App
The Miele App is available to download
free of charge from the Apple App
Store
®
or from the Google Play Store™.
Setting up networking for the first time
Tap the symbol.
Swipe left or right until the symbol
is shown in the middle.
Tap the symbol.
Tap the connection method you wish
to use (app or WPS).
After you have successfully logged in,
the symbol will appear on the display.
If a connection could not be estab-
lished, the symbol will appear.
In this case, start the process again.
To leave the Settings level, tap the
symbol.
Performing Scan & Connect
Scan the QR code.
If you have installed the Miele app and
have a user account, you will be taken
directly to the networking steps.
If you have not yet installed the Miele
app, you will be taken to the Apple App
Store
®
or the Google Play Store™.
Install the Miele app and set up a user
account.
Scan the QR code again.
The Miele app will guide you through
the setup process.
(depending on the model)
39
Operation
The correct temperature
It is very important to set the correct
temperature to ensure the shelf life of
food. Reducing the temperature reduces
the growth rate of microorganisms.
Food does not spoil as quickly.
The temperature in the refrigeration ap-
pliance will rise:
- The more often the appliance door is
opened and the longer it is kept open
- The more food that is stored in it
- The warmer the food is which is being
put into it
- The higher the ambient temperature
surrounding the refrigeration appli-
ance. This refrigeration appliance is
designed for use within specific ambi-
ent temperatures (climate range). Do
not use in ambient temperatures for
which it is not designed.
...in the refrigerator section and in the
PerfectFresh Active zone
We recommend a temperature of 4°C
in the refrigerator section.
The temperature in the PerfectFresh
Active zone is controlled automatically
and maintained at 0 to 3°C.
Automatic temperature distribution
(DynaCool)
The fan switches on automatically when
the cooling system for the refrigerator
switches on. It distributes the temperat-
ure in the appliance to all areas more
evenly so that all the food will be chilled
to about the same degree.
Temperature display
In normal operation, the temperature
display shows the current average re-
frigerator section temperature inside
the refrigeration appliance.
Depending on the ambient temperature
and the temperature setting, it can take
the appliance a few hours to reach the
temperature required and for this tem-
perature to then be shown as a constant
temperature on the display.
Setting the temperature
Touch the temperature display on the
display.
Swipe left or right until the temperat-
ure you want is shown in the middle.
Tap on the temperature you want to
confirm.
The temperature display will then
change back to the current temperature
in the refrigeration appliance.
Possible temperature settings
- Refrigerator section: 3to9°C
Adjusting the temperature level in the
PerfectFreshActive zone
The temperature in the
PerfectFreshActive zone is automatic-
ally controlled between 0 and 3°C.
However, if you would like it to be
warmer or colder, e.g. when storing fish,
you can adjust the temperature slightly
in increments.
Tap.
Swipe left or right until is shown in
the middle.
Tap.
40
Operation
Swipe left or right until the setting you
want (1: lowest temperature; 9:
highest temperature) is shown in the
middle.
Tap on the setting you want to con-
firm.
The factory default setting for the
temperature level is5.
Under certain circumstances, a set-
ting from1 to4 can cause the tem-
perature to fall below 0°C. This can
cause food to freeze.
Check the temperature setting.
Door alarm
Door alarm with manual door opening
The appliance door is left open for an
extended period.
The refrigeration appliance is fitted
with a door alarm to avoid increased
energy consumption and refrigerated
items becoming warm if the door is
left open.
If the appliance door is left open for an
extended period,
will light up yellow
in the temperature display. An alarm will
also sound and the interior lighting will
flash.
The time before the door alarm is
triggered can be changed (see “Select-
ing further settings”).
The door alarm’s audible signal can be
switched off (see “Selecting further set-
tings”).
The alarm will stop and
will go out in
the display as soon as the door is
closed.
Switching the door alarm off early
Tap the
symbol.
The alarm will stop, the
symbol will
go out and the interior lighting will light
up again constantly.
If the appliance door is not closed, the
door alarm will sound again after
around 1minute.
Door alarm with automatic door open-
ing
ActiveDoor closes after a short time.
The refrigeration appliance is fitted
with a door alarm to avoid increased
energy consumption and refrigerated
items becoming warm if the door is
left open.
If the appliance door is left open for too
long, will light up yellow in the dis-
play. An alarm will also sound and the
interior lighting will flash.
You cannot change the time until the
door alarm is triggered.
The door alarm’s audible signal can be
switched off (see “Selecting further set-
tings”).
After a short time, the door will close
automatically. The alarm will stop
and will disappear from the display.
Switching the ActiveDoor door alarm
off early
Touch in the display.
The alarm will stop, the symbol will
go out and the interior lighting will light
up again constantly.
If the appliance door is not closed, the
door alarm will sound again after around
1minute.
41
Operation
will light up yellow in the temperat-
ure display. An alarm will also sound and
the interior lighting will flash (see “Door
alarm: Appliance door is left open for an
extended period”).
Using Super cool
SuperCool
When switched on, the SuperCool
function can be used to rapidly re-
duce the temperature in the fridge
zone to its lowest setting (depending
on the ambient temperature). The refri-
geration appliance will work at full
power and lower the temperature. Se-
lect this function for the rapid chilling
of large amounts of fresh food or drink.
When the SuperCool function is
switched on, the appliance may make
more noise than usual.
The SuperCool function should be
switched on 4hours before placing
food or drinks in the fridge zone.
The SuperCool function will switch
itself off automatically after approx.
12hours. The refrigeration appliance
will then run at normal power again.
Tip: To save energy, you can switch the
SuperCool function off yourself once
food and drinks are sufficiently chilled.
Switching SuperCool on and off
Touch the temperature display for the
fridge zone.
Touch to switch the SuperCool
function on and off again.
When the SuperCool function is
switched on, will light up orange.
Tap on the temperature display to
leave the Settings level.
Storing food in the fridge zone
Different storage zones
Due to natural air circulation, there are
different temperature regions in the re-
frigerator section.
Cold, heavy air sinks to the lowest sec-
tion of the refrigeration section. Make
use of the different zones when placing
food in the appliance.
This is a refrigeration appliance with
automatic temperature distribution
(DynaCool). The refrigeration appli-
ance switches the fan on automatically
when the cooling system for the fridge
zone switches on. This means that the
cold is distributed evenly in the fridge
zone and the difference between the
various temperature zones is less pro-
nounced. All stored food is thus cooled
to approximately the same temperat-
ure.
Warmest area
The warmest area in the refrigerator
section is at the top in the front area
and in the door. Use this for storing but-
ter and cheese.
42
Operation
Coldest area
The coldest area in the fridge zone is
directly above the PerfectFreshActive
zone dividing plate and at the back of
the appliance. The temperature in the
PerfectFreshActive zone compartments
is even colder.
A temperature setting of 4°C com-
bined with appropriate hygiene
measures delays the propagation of
bacteria, e.g. salmonella and listeria,
which can lead to serious food pois-
oning.
Therefore, you should use these areas in
the fridge zone and in the
PerfectFreshActive zone to store all
delicate and highly perishable food, in-
cluding:
- Fish, meat, poultry
- Cold cuts, ready meals
- Dishes or baked goods containing
eggs or cream
- Fresh dough, cake mixtures, pizza or
quiche dough
- Raw milk cheese and other raw milk
products
- Hummus, vegetable spreads, plant-
based cream cheese substitutes
- Pre-packed vegetables
- Other fresh food (with a label stating it
should be kept at a temperature of ap-
prox. 4°C)
Should food be stored loose or in
packaging?
Ensure that food stored in the fridge
zone is in packaging or covered properly
(some exceptions apply in the
PerfectFreshActive zone).
This will prevent food odours from af-
fecting other food, stop food from drying
out and also prevent any cross-contam-
ination of germs. This is particularly im-
portant when storing meat products.
Make sure that food such as raw meat
and fish in particular does not come into
contact with other food.
By ensuring that the temperature
settings are correct and by taking ap-
propriate hygiene measures, you can
prolong the storage life of your food
considerably. This prevents food
waste.
Storing food in the PerfectFresh
Active zone
PerfectFresh Active zone
The PerfectFresh Active zone satisfies
the requirements of a chill compart-
ment to DINEN62552:2025.
The PerfectFresh Active zone provides
ideal storage conditions for fruit, veget-
ables, fish, meat and dairy products.
Food stays fresh considerably longer
while retaining both flavour and vitam-
ins.
The temperature in the PerfectFresh
Active zone is controlled automatically
and maintained at 0to3°C. While
lower than the temperature in a stand-
ard refrigerator section, this is the op-
timum temperature range for storing
fresh food which is not sensitive to cold.
The humidity level in the PerfectFresh
Active zone can also be regulated to suit
the food being stored. If the humidi-
fier is switched on, water vapour is
supplied to the stored fruit and veget-
ables. The humidifier switches on ap-
proximately every 90minutes and each
time the appliance door is opened. Food
43
Operation
retains its own moisture if stored at a
higher humidity and so does not dry out
as quickly.
Remember that the fresher the food
when placed in the appliance, the
longer it will stay fresh.
Take food out of the PerfectFresh Act-
ive zone approx.30to60minutes be-
fore using it. The aroma and taste do
not fully develop until the food has
reached room temperature.
Humidity-controlled compartment
| |
The upper humidity-controlled com-
partment has a temperature of
0to3°C, and the humidity level is in-
creased depending on the position of
the compartment cover: not in-
creased or increased.
Humidity level not increased
When the setting is used, the humid-
ity-controlled compartment becomes a
dry compartment (see “Dry compart-
ment”).
Increased humidity
At this setting, the humidity-controlled
compartment is suitable for storing fruit
and vegetables.
Increased humidity in the humidity-
controlled compartment can cause a
build-up of condensate.
If you find that too much condensate
has formed and this is affecting the
food, proceed as follows:
Wipe off any condensate with a
cloth.
Open the compartment cover by
moving it to the low humidity posi-
tion.
Switch off the humidifier .
Selecting increased humidity
When the setting is used, the hu-
midifier should be switched on.
The energy consumption does in-
crease slightly when the humidifier
is switched on. The appliance may also
make more noise than usual.
Tap.
Swipe left or right until is shown in
the middle.
Tap.
Swipe left until the humidifier intens-
ity you want (1: low humidity; 3: max-
imum humidity) is shown in the
middle.
Tap on the setting you want to con-
firm.
The symbol lights up orange.
Open the drawer of the humidity-con-
trolled compartment.
44
Operation
Slide the compartment cover back-
wards as far as it will go.
The compartment cover is closed and
the humidity remains in the compart-
ment.
Selecting low humidity
When the setting is used, the humid-
ifier should be switched off.
Tap.
Swipe left or right until is shown in
the middle.
Tap.
Swipe right and tap.
The symbol lights up white.
Open the drawer of the humidity-con-
trolled compartment.
Pull the compartment cover forwards
as far as it will go.
The compartment cover is open and the
humidity drops .
If the food is higher than the edge of
the drawer, pushing in the drawer
may alter the position of the com-
partment cover, causing it to close.
When filling the drawer, take care to
ensure that the food does not touch
the compartment cover.
45
Operation
Humidifier
When the humidifier is switched on,
water vapour is supplied to the fruit
and vegetables stored in the humidity-
controlled compartment each time the
appliance door is opened and approx-
imately every 90minutes. The water
vapour provides additional humidity in
the humidity-controlled compartment.
The humidifier and its water container
are located in the dividing plate between
the refrigerator section and
PerfectFresh Active zone.
Check and pay attention to the following
before switching the humidifier on (see
“Selecting further settings”):
- The water container must have been
cleaned, filled with water and fitted
securely.
- The cover for the humidity-controlled
compartment must be closed
(setting).
The water in the water container
should last for approx. 4months.
The water container will only need to
be refilled if the humidifier is no longer
producing any water vapour.
Risk of damage due to incorrectly
filled water container.
Liquids containing sugar can damage
the humidifier.
Use only fresh drinking water to fill
the water container.
Risk to health due to contamin-
ated water.
Using contaminated water can lead
to poisoning.
Use only fresh drinking water to fill
the water container.
Risk to health due to contamin-
ated water.
Bacteria can develop in water which
has been sitting in the water con-
tainer for too long. This poses a risk
to your health.
If the refrigeration appliance, the
fridge zone or the humidifier has
been out of operation for more than
2days, clean the water container and
fill it with fresh drinking water.
If Holiday mode has been activ-
ated for more than 2weeks, clean
the water container and fill it with
fresh drinking water.
Filling the water container for the hu-
midifier
Press on the outer corners at the back
of the glass shelf.
The glass shelf will lift up at the front.
Lift up the shelf and fold it back.
The glass shelf will stand upright.
Push the slider to the left.
The water container will spring out of
the recess.
Remove the water container and fill it
up to the marker with drinking water.
Reinsert the water container.
Fold the glass shelf back down.
46
Operation
Dry compartment
|
The dry compartment has a temperat-
ure of 0to3°C and the humidity is not
increased .
The dry compartment is ideal for storing
food which goes off quickly, such as:
- Fresh fish and shellfish
- Meat, poultry and sausage
- Deli salads
- Dairy products, such as milk, yoghurt,
cheese, double cream, etc.
- Plant-based products such as tofu,
oat drinks, hummus, vegetable
spreads, meat and cheese substi-
tutes, etc.
- Any type of food can in fact be stored
in this compartment, as long as it is
packaged.
Please note that food rich in protein
deteriorates faster than other types
of food.
Shellfish, for example, deteriorates
faster than fish, and fish deteriorates
faster than meat.
For hygiene reasons, always keep
these foods covered or wrapped.
47
Operation
Observe the following tips if you find that food you have stored does not keep
well (e.g. food becomes limp or wilts after only being stored for a short time):
Only place fresh food in the appliance. The initial condition of the food is crucial
to maintaining freshness.
Clean the compartments in the PerfectFresh Active zone before storing food in
them.
Very wet food should be dried off before storing it.
Do not store any food in the PerfectFresh Active zone which is sensitive to cold.
Select the correct PerfectFresh Active compartment for the food as well as the
correct position for the compartment cover (humidity not increased or humidity
increased).
An increased humidity level in the humidity-controlled compartment is
achieved with the moisture present in the food being stored if the food is stored
unwrapped. The more food stored in the compartment, the higher the humidity.
Do not overfill the compartments.
If you find that too much condensate has formed when using the setting and
this is affecting the food:
- Wipe off any condensate with a cloth.
- Place a rack or similar item in the compartment so that excess moisture can drain
away.
- Open the compartment cover by moving it to the low humidity position and
switch the humidifier off.
If the humidity level is too low despite the setting, wrap the food in airtight
packaging.
If you think that the temperature in the PerfectFresh Active zone is too high or
too low, try regulating it slightly first by changing the temperature in the fridge
zone by 1or2°C. If ice crystals start to form on the base of the PerfectFresh
Active compartments, increase the temperature as otherwise the cold temperat-
ure will damage the food.
If adjusting the temperature in the fridge zone does not remedy the problem, ad-
just the temperature in the PerfectFresh Active zone (see “Adjusting settings”).
48
Selecting further settings
Explanation of the different set-
tings
Only the settings that require further ex-
planation are described below.
The door alarm and other warnings are
automatically suppressed when you
are in Settings mode.
Party mode
The Party mode function is particu-
larly recommended for the rapid
chilling of large amounts of fresh food
or drink.
Tip: Switch on the Party mode func-
tion approx. 4hours before placing
food and drinks in the appliance.
When Party mode is switched on, the
SuperCool function is switched on
automatically.
Party mode cannot be switched on if
Holiday mode is switched on.
The Party mode function will switch
itself off automatically after approx.
24hours. However, you can switch the
Party mode function off early at any
time.
Holiday mode
The Holiday mode function is use-
ful when you go on holiday, for ex-
ample, if you do not wish to switch off
the refrigerator section completely or
do not need a high degree of cooling.
If Holiday mode is switched on, this
will be indicated on the start display. It
can be switched off via the start display
or Settings mode.
The refrigerator section is regulated at a
temperature of 15°C, which automatic-
ally sets the temperature in the
PerfectFresh Active zone to between
9and12°C. In this way, the refrigerator
section remains in operation whilst sav-
ing energy.
Food which does not go off quickly can
be stored in the refrigeration appliance
for some time at this moderate refri-
gerator temperature. Energy consump-
tion is lower than in normal operation.
This also prevents the build-up of
odours and mould, which can occur if
the refrigerator section is switched off
and the appliance door is closed.
Health risk caused by decompos-
ing food.
The usability and quality of food in
the fridge zone may deteriorate if the
temperature remains above 4°C for
an extended period.
Only ever switch on the Holiday
mode function for a limited
period.
Do not store any temperature-sensit-
ive food which goes off easily, such
as fruit, vegetables, fish, meat and
dairy products, during this time.
Switching the lock function/ on
When the lock function is switched on,
it protects the refrigeration appliance
from being switched off unintentionally
and being adjusted unintentionally by
unauthorised persons, e.g. children.
Tap.
Swipe left or right until is shown in
the middle.
49
Selecting further settings
Tap.
When the lock function is switched on,
will light up orange.
Close the appliance door. Only then
will the lock function be active.
Deactivating the lock function/
temporarily
If you want to adjust the temperature,
for example, you can deactivate the lock
function temporarily:
Touch the temperature display.
Touch for approx. 6seconds.
The display switches to the temperature
controls.
Now select the required settings.
Closing the appliance door will reactiv-
ate the lock function.
Switching the lock function/ off
completely
Tap.
Touch for approx. 6seconds.
Swipe left or right until is shown in
the middle.
Tap.
When the lock function is switched off,
will light up.
Sabbath mode
The refrigeration appliance offers a Sab-
bath mode for the purposes of religious
observance.
If Sabbath mode is switched on, this
will be indicated on the start display.
The display switches off after
3seconds.
When Sabbath mode is switched on,
you cannot make any settings on your
refrigeration appliance.
Ensure that the appliance door is prop-
erly closed, as visual and audible
alarms are switched off.
The Sabbath mode function will
switch off automatically after approx.
80hours.
When Sabbath mode is switched on,
the following are deactivated:
- Interior lighting when the door is
opened
- All visual and audible signals
- The temperature display
- An active WiFi connection
All other functions switched on previ-
ously remain activated.
Health risk caused by decompos-
ing food.
As power failures are not indicated
while Sabbath mode is active, food
may be exposed to increased tem-
peratures for a certain period of time.
This will reduce the storage life of the
food.
If there is a power failure during Sab-
bath mode, check the quality of the
food.
Switching Sabbath mode off
Tap on the black display.
will appear in the display.
50
Selecting further settings
Tap .
will light up orange.
Tap the symbol again.
When Sabbath mode is switched off,
the symbol will light up white.
Automatic door opening (Active-
Door)
A
The following settings can be con-
figured:
1. Activate and configure ActiveDoor
when commissioning the refrigera-
tion appliance or at a later point
2. Deactivate ActiveDoor
3. Activate ActiveDoor if the function
has already been configured and de-
activated
4. Change the set door opening angle
1.Activate and configure ActiveDoor
for the first time
Activation and configuration consist of
multiple steps:
Activating ActiveDoor
Tap.
Swipe left or right until
A
is shown in
the middle.
Tap
A
.
will light up yellow in the display.
Tap OK.
will light up yellow in the display.
You now need to set the door opening
angle.
Setting the door opening angle
Leave the area of the door opening
range clear.
Open the door to the required door
opening angle (at least70°).
Tip: To ensure the drawers can be
pulled out without any problems, select
a door opening angle of at least 90°.
Tap OK.
will light up yellow in the display.
Tap OK.
- If appears in the display, the door
opening angle was not successfully
saved.
Tap to confirm the information.
will light up yellow in the display.
Start again from the “Setting the
door opening angle” step.
- If appears in the display, the door
opening angle has been saved suc-
cessfully.
Tap to confirm the information.
will light up yellow in the display.
You now need to perform a reference
run.
Performing a reference run
Risk of injury during automatic
opening and closing of the appliance
door
Body parts such as fingers can be-
come jammed in the area of the door
opening range and in the door hinge
area.
Leave the area of the door opening
range clear.
Do not reach into the door hinge area
or inside the refrigeration appliance
with your hand while the door is clos-
ing.
Do not block the door.
51
Selecting further settings
Risk of damage while the appli-
ance door is closing automatically
Drawers or telescopic runners that
are pulled out can be damaged (de-
pending on the model).
Push in drawers fully.
Push in telescopic runners fully after
removing a drawer.
Tap OK.
The reference run will start. During the
reference run, the door will close and
open again automatically once.
At the same time,
A
will flash in the
display and a buzzer will sound.
- If
appears in the display, the refer-
ence run was not successful.
Tap
to confirm the information.
A
will light up yellow in the display.
Start again from the “Activating
ActiveDoor” step.
- If
appears in the display, the refer-
ence run was successful.
Tap
to confirm the information.
will light up yellow in the display.
You now need to save the selected
door opening angle.
Saving the selected door opening
angle
Tap OK.
If appears in the display, the door
opening angle has been saved success-
fully.
Tap to confirm the information.
will light up orange in the display.
ActiveDoor is activated.
2.Deactivate ActiveDoor
Tap.
Swipe left or right until
A
is shown in
the middle.
Tap
A
.
will light up orange in the display.
Tap.
will light up white and ActiveDoor
will be deactivated.
3.Activate ActiveDoor
Tap.
Swipe left or right until
A
is shown in
the middle.
Tap
A
.
will appear in the display.
Tap.
will light up orange and ActiveDoor
will be activated.
4.Change the set door opening angle
Tap.
Swipe left or right until
A
is shown in
the middle.
Tap
A
.
will light up orange in the display.
Swipe left or right until is shown in
the middle.
Tap.
will light up yellow in the display.
You now need to set the door opening
angle.
Setting the door opening angle
Leave the area of the door opening
range clear.
52
Selecting further settings
Open the door to the required door
opening angle (at least70°).
Tip: To ensure the drawers can be
pulled out without any problems, select
a door opening angle of at least 90°.
Tap OK.
will light up yellow in the display.
Tap OK.
- If appears in the display, the door
opening angle was not successfully
saved.
Tap to confirm the information.
will light up yellow in the display.
Start again from the “Setting the
door opening angle” step.
- If appears in the display, the door
opening angle has been saved suc-
cessfully.
Tap to confirm the information.
will light up yellow in the display.
You now need to perform a reference
run.
Performing a reference run
Risk of injury during automatic
opening and closing of the appliance
door
Body parts such as fingers can be-
come jammed in the area of the door
opening range and in the door hinge
area.
Leave the area of the door opening
range clear.
Do not reach into the door hinge area
or inside the refrigeration appliance
with your hand while the door is clos-
ing.
Do not block the door.
Risk of damage while the appli-
ance door is closing automatically
Drawers or telescopic runners that
are pulled out can be damaged (de-
pending on the model).
Push in drawers fully.
Push in telescopic runners fully after
removing a drawer.
Tap OK.
The reference run will start. During the
reference run, the door will close and
open again automatically once.
At the same time,
A
will flash in the
display and a buzzer will sound.
- If
appears in the display, the refer-
ence run was not successful.
Tap
to confirm the information.
A
will light up yellow in the display.
Start again from the “Activating
ActiveDoor” step.
- If
appears in the display, the refer-
ence run was successful.
Tap
to confirm the information.
will light up yellow in the display.
You now need to save the selected
door opening angle.
Saving the selected door opening
angle
Tap OK.
If appears in the display, the door
opening angle has been saved success-
fully.
Tap to confirm the information.
will light up orange in the display.
ActiveDoor is activated.
53
Selecting further settings
Change the time until the door alarm
is triggered
when the door is
opened manually
You can set how quickly the door alarm
should sound after the appliance door
has been opened manually.
Tap.
Swipe left or right until
is shown
in the middle.
Tap
.
Swipe left or right until the time you
want between 30seconds and
3minutes 30seconds is shown in the
middle.
Tap to confirm the setting.
Networking
Your refrigeration appliance is equipped
with an integrated WiFi module. The
WiFi module makes it possible to con-
nect to your home network and to use
the Mieleapp on a mobile device.
Once your refrigeration appliance has
been connected via WiFi, the connec-
tion is automatically re-established
every time it is switched on.
Make sure that your WiFi network sig-
nal is strong enough in the place where
you intend to install your refrigeration
appliance.
Connecting your refrigeration appli-
ance to your WiFi network will in-
crease energy consumption, even
when the appliance is switched off.
You can switch off the connection to
your WiFi network in the settings.
Smart Extras via the Miele app*
Networking via the Miele app gives you
access to numerous Smart Extras, in-
cluding:
- Access status information.
- Use additional helpful functions.
- Keep your refrigeration appliance up
to date with the latest Miele develop-
ments via software updates.
You can find more detailed information
about Smart Extras on the Miele web-
site, in the Apple App Store
®
or in the
Google Play Store™.
*This is a separate digital offer from
Miele & Cie. KG. The range of func-
tions can vary depending on the model
and the country. Acceptance of the
Terms and Conditions and Privacy
Policy for Miele digital products & ser-
vices in the Miele app required. Miele
reserves the right to change or discon-
tinue the digital offer at any time.
Setting up networking for the first time
Tap the symbol.
Swipe left or right until the symbol
is shown in the middle.
Tap the symbol.
Tap the connection method you wish
to use (app or WPS).
After you have successfully logged in,
the symbol will appear on the display.
If a connection could not be estab-
lished, the symbol will appear.
In this case, start the process again.
To leave the Settings level, tap the
symbol.
54
Selecting further settings
Deactivating the WiFi connection
Tap the symbol.
Swipe left or right until the symbol
is shown in the middle.
Tap the symbol.
Tap the symbol to deactivate the
WiFi connection.
The symbol appears.
To leave the Settings level, tap the
symbol.
Activating the WiFi connection
Tap the symbol.
Swipe left or right until the symbol
is shown in the middle.
Tap the symbol.
Tap the symbol to activate the WiFi
connection.
The symbol appears.
To leave the Settings level, tap the
symbol.
When the WiFi connection is active, the
symbol will light up on the display.
Resetting the network configuration
Tap the symbol.
Swipe left or right until the symbol
is shown in the middle.
Tap the symbol.
Swipe right until the symbol is
shown in the middle.
Tap the symbol.
Tap the symbol.
To leave the Settings level, tap the
symbol.
All entered settings and values are reset
to the default settings.
The WiFi connection has been deactiv-
ated. The symbol will go out on the
start display.
Reset the network configuration if
you are disposing of or selling your
refrigeration appliance, or if you are
putting a used refrigeration appliance
into operation. All personal data is re-
moved from the refrigeration appli-
ance. This will also ensure that a pre-
vious owner is no longer able to ac-
cess the refrigeration appliance.
Changing the volume of the alarms
and buzzers/
You can change the volume of the
alarms and buzzers (e.g. in the event of
a door alarm or a fault message). Altern-
atively, you can switch the alarms and
buzzers off if you find them annoying.
Tap.
Swipe left or right until is shown in
the middle.
Tap.
Select the volume you want by swip-
ing the segment bar to the left or
right.
Confirm the volume you want by tap-
ping on the segment bar.
When the alarms and buzzers are
switched off, will appear.
Adjusting the display brightness
You can adjust the display brightness to
the lighting conditions in the room.
Tap.
Swipe left or right until is shown in
the middle.
Tap.
55
Selecting further settings
Select the brightness you want by
swiping the segment bar to the left or
right.
Confirm the brightness you want by
tapping on the segment bar.
Switching off Demo mode
Demo mode allows the refrigeration
appliance to be presented in the show-
room without the cooling system being
switched on. This setting is not needed
for domestic use.
If Demo mode has been switched on
as a default setting, will show on the
start display.
Tap.
Tap.
Swipe left or right until is shown in
the middle.
Tap.
After Demo mode has been switched
off, the refrigeration appliance shuts
down and must be switched on again.
Resetting the settings to their default
settings
All settings made on the refrigeration
appliance will be reset to default set-
tings (for settings, see “Guide to the ap-
pliance”).
Tap.
Swipe left or right until is shown in
the middle.
Tap.
will appear on the display.
Tap OK.
The refrigeration appliance shuts down
and must be switched on again.
Information
Appliance data (model identifier and
serial number) is shown on the display.
Keep this appliance data to hand:
- For integrating the refrigeration appli-
ance into your WiFi network (see “Se-
lecting further settings –
Miele@home”) (depending on the
model).
- When reporting an appliance fault to
the Miele Customer Service Depart-
ment (see “Service”).
- When retrieving information from the
EPREL database (see “Service”).
Charcoal filter change indicator
After inserting the charcoal filter (op-
tional accessory), you must activate the
charcoal filter change indicator in
Settings mode.
The charcoal filter change indicator
on the start display will remind you to
replace the charcoal filter approx.
every 6months (see “Cleaning and
care – Replacing the charcoal filters”).
Cleaning mode
Cleaning mode makes it easier to
clean the fridge zone (see “Cleaning
and care”). The interior lighting re-
mains switched on, even though the
fridge zone is switched off. The buzzer
will stop and the symbols on the dis-
play will also go out.
If Cleaning mode is switched on,
this will be indicated on the start dis-
play.
56
Selecting further settings
After cleaning, Cleaning mode must
be switched off. If the appliance door is
closed for more than 10minutes, Clean-
ing mode switches itself off auto-
matically.
57
Cleaning and care
The data plate located inside the in-
terior cabinet of the refrigeration appli-
ance must not be removed. It contains
information which is required in the
event of a service call.
Do not let water get into the elec-
tronic unit or the lighting.
Risk of damage due to moisture
ingress.
The steam from a steam cleaner can
damage plastic and electrical com-
ponents.
Do not use a steam cleaner to clean
the refrigeration appliance.
Defrosting
Fridge zone and
PerfectFresh Active zone
The fridge zone and the
PerfectFresh Active zone defrost auto-
matically.
Cleaning agents
Cleaning and conditioning agents
used in the interior cabinet of the re-
frigeration appliance must be food
safe.
To avoid damaging the surfaces of the
appliance, do not use the following:
- Cleaning agents containing soda, am-
monia, acids or chlorides
- Cleaning agents containing descaling
agents
- Abrasive cleaning agents (e.g. scour-
ing powder, scouring liquid or pumice
stones)
- Cleaning agents containing solvents
- Stainless steel cleaners
- Dishwasher cleaner
- Oven sprays
- Glass cleaning agents
- Hard, abrasive sponges and brushes
(e.g. pot scourers)
- Eraser stain remover blocks
- Sharp metal scrapers
We recommend using a clean sponge
and lukewarm water with a little wash-
ing-up liquid to clean the surfaces of the
appliance.
Preparing the refrigeration ap-
pliance for cleaning
Use the cleaning mode.
Take any food out of the fridge zone
and store it in a cool place.
If necessary, take out all removable
parts for cleaning.
Cleaning the interior of the ap-
pliance
Clean the refrigeration appliance reg-
ularly, or at least once a month.
If soiling is left on for any length of
time, it may become impossible to
remove under certain circumstances.
Surfaces may suffer discolouration or
damage.
It is therefore best to remove any
soiling immediately.
Clean the interior with a clean sponge
cloth, lukewarm water and a little
washing-up liquid.
After cleaning, wipe with clean water
and dry with a cleaning cloth.
58
Cleaning and care
Clean the condensate channel and
drain hole using a cotton swab or sim-
ilar item.
Leave the door open to air the refri-
geration appliance sufficiently for a
short while and to prevent odour
build-up.
Cleaning accessories by hand
or in the dishwasher
The following components must be
cleaned by hand only:
- The stainless steel trims or strips
- Flexible bottle rack
- Door shelf with fine adjustment
- The plastic parts of the adjustable
shelf with pivotable glass shelf (Flexi-
Tray)
- The rear protective strip and the side
supports of the storage drawer (Com-
pactCase)
- shelf with printing
- The dividing plate and bottle rack
- All drawers and compartment lids
(these vary depending on model)
- The organisation box
The following components are dish-
washer-safe:
Risk of damage due to high dish-
washer temperatures.
Parts of the refrigeration appliance
may become unusable, e.g. deform, if
they are washed in the dishwasher at
more than 55°C.
For dishwasher-safe components, al-
ways select dishwasher programmes
with a maximum temperature of
55°C.
Contact with natural dyes from car-
rots, tomatoes and ketchup, etc., may
discolour the plastic parts in the dish-
washer. This discolouration does not
affect the stability of the parts.
- Bottle holder, egg tray
- Shelves and bottle shelves in the ap-
pliance door (without stainless steel
trim)
- The guide rails for the door shelf with
fine adjustment
- Adjustable shelves (without the trim
or printing)
- The 2pieces that make up the water
container for the humidifier
- The adapters for the baking tray
- The holder for the charcoal filter (avail-
able as an optional accessory)
Removing and dismantling ac-
cessories for cleaning
Removing the door shelf with fine ad-
justment
Hold the door shelf in both hands,
press the grey buttons on both sides
under it and slide it up off the guide
rails.
Remove the guide rail from the lugs.
59
Cleaning and care
Once you have cleaned it, move the
guide rail to the desired position and
place the second guide rail parallel to
the first rail on the opposite side.
Push the shelf back down onto the
guide rails.
Dismantling the door shelf/bottle shelf
Remove the stainless steel trim before
cleaning the door shelf/bottle rack in a
dishwasher.
To remove the stainless steel trim, pro-
ceed as follows:
Place the door shelf/bottle rack on
the worktop.
Press the latch out of the recess. The
entire section of stainless steel trim
will now come off the shelf.
After cleaning, reattach the stainless
steel trim to the shelf by following the
same procedure in reverse.
Dismantling the adjustable shelf/ad-
justable shelf with lighting
Risk of damage as a result of in-
correct cleaning.
The stainless steel trim with LED
lighting will be damaged if you place
it in water for cleaning.
Clean the stainless steel trim with
LED lighting with a damp cloth.
Remove the stainless steel trim or
stainless steel trim with LED lighting
before cleaning the adjustable shelf.
Place the adjustable shelf on a work-
top covered with a soft material (e.g.
a tea towel) with the top side facing
downward.
Risk of damage as a result of in-
correct handling.
When you remove the stainless steel
trim with LED lighting, the metal con-
tacts can be damaged.
These contacts in the front left
corner supply power to the LED light-
ing. Ensure that you always loosen
the side on which the contacts are
not located first.
Grasp the plastic surround on the left-
hand side of the stainless steel trim at
its rearmost point.
1. Pull the plastic surround from the ad-
justable shelf and
60
Cleaning and care
2. pull the trim off at the same time.
The opposite side will also be re-
leased.
After cleaning, reattach the stainless
steel trim by following the same pro-
cedure in reverse.
Dismantling the adjustable shelf with
pivotable glass shelf (FlexiTray)
Danger of injury from dropping
the glass shelf.
The pivotable glass shelf can come
out when removing the adjustable
shelf, causing the glass shelf to drop
out of the tray and break.
Keep hold of the pivotable glass shelf
when removing the adjustable shelf.
Place the adjustable shelf with pivot-
able glass shelf on a worktop covered
with a soft material (e.g. a tea towel).
Bring the tray to the front. Use the
opening to lift the glass shelf from un-
derneath and remove it.
Move the tray back to its original pos-
ition resting on the adjustable shelf.
The tray can only be detached from
the adjustable shelf once it has been
returned to its original position and is
resting on the adjustable shelf. The
fastener must be sitting in the circu-
lar recess at the end of the runner
guide.
Take a firm hold of the top right of the
bottom adjustable shelf and pull the
tray firmly off the adjustable shelf.
The fastener on the tray comes loose
from the circular recess at the end of
the runner guide.
You can now dismantle all the parts and
clean them.
Underneath the plastic shelf, there is a
glass shelf which is held in place with
retainers on the outer edge of the
adjustable shelf.
The glass shelf can also be removed
for cleaning as described below:
Move the shelf so that the stainless
steel trim is at the back and the front
edge hangs over the worktop slightly.
61
Cleaning and care
Release the retainers and lift the
shelf up.
The glass shelf comes loose. Both parts
can now be cleaned.
Assembling the adjustable shelf with
pivotable glass shelf (FlexiTray)
Put the plastic adjustable shelf down
on the worktop so that the recess is
at the top and the stainless steel trim
is at the front.
Place the glass shelf in the grooves
and then secure it in the retainers.
Turn over the shelf so that the plastic
surface is facing upwards.
Place the frame on the adjustable
shelf so that the arrows on the ad-
justable shelf line up with the re-
cesses on the frame.
Take hold of the tray with the fastener
facing downwards and push the
fastener firmly into the circular recess
at the end of the runner guide.
Place the glass shelf in the tray.
62
Cleaning and care
Removing and dismantling the storage
drawer (CompactCase)
Pull the drawer out as far as it will go.
Tilt the drawer slightly upwards and
remove it.
Use both hands to raise the shelf and
the support slightly at the front 1.).
Pull the shelf slightly forwards 2.) and
remove it by lifting it either up or out
at an angle, making sure that the
notches on the left and right are in
line with the shelf supports.
Place the shelf and support on a
worktop covered with a soft material
(e.g. a tea towel).
Pull the supports off the sides of the
shelf 1.).
Pull the stainless steel trim forward
and off the shelf 2.).
After cleaning the shelf, reattach the
stainless steel trim, the protective
strip and the supports.
Insert the shelf together with the sup-
port into the refrigeration appliance
either from above or from the side.
Slide the shelf back as far as it will go.
Insert the drawer from above into the
upper or lower guide in the support as
required.
Removing the drawers from the fridge
zone
Pull the drawer out as far as it will go.
The drawer is clipped into place at the
back using clips. It must be unclipped
for removal.
63
Cleaning and care
1. Lift the left clip and, at the same
time, pull the drawer forwards to un-
clip it.
2. Do the same on the opposite side.
The drawer is no longer clipped into
place.
3. Now pull out the drawer firmly from
the front.
Push the telescopic rails back in
again to avoid damaging them.
Risk of damage as a result of in-
correct cleaning.
The telescopic rails contain a special
lubricant which can be washed out
during cleaning, damaging the rails.
Wipe the telescopic rails with a
damp cloth to clean them.
Replacing the drawers
Place the drawer on the fully retracted
telescopic rails.
Push the drawer firmly into the refri-
geration appliance until you hear it
click into place.
Removing and dismantling the water
container for the humidifier
Risk to health due to contamin-
ated water.
Bacteria can develop in water which
has been sitting in the water con-
tainer for too long. This poses a risk
to your health.
If the refrigeration appliance, the
fridge zone or the humidifier has
been out of operation for more than
2days, clean the water container and
fill it with fresh drinking water.
If Holiday mode has been activ-
ated for more than 2weeks, clean
the water container and fill it with
fresh drinking water.
Press on the outer corners at the back
of the glass shelf.
The glass shelf will lift up at the front.
Lift up the shelf and fold it back.
The glass shelf will stand upright.
Push the slider to the left.
The water container will spring out of
the recess.
Remove the water container.
64
Cleaning and care
Separate the water container into its
2pieces and clean them by hand or in
the dishwasher.
Reinsert the water container.
Fold the glass shelf back down.
Removing the dividing plate and bottle
rack
Remove the glass shelves at the front
and back of the dividing plate.
Lift the bottle rack at the front and
pull it out.
After cleaning, slide the bottle rack all
the way in and push it down.
Place the glass shelves back on the
dividing plate.
Removing the compartment cover
Lift the cover at the front and pull it
out.
After cleaning, slide the compartment
cover back in again.
Replacing the ActiveAirCleanfilter
(charcoal filter)
New ActiveAirCleanfilters can be ob-
tained from the Miele Customer Ser-
vice Department, your Miele dealer or
the Miele website.
Pull the charcoal filter holder upwards
to remove it from the adjustable shelf.
When in position, the charcoal filters
must not touch the rear wall of the
refrigeration appliance as the mois-
ture could cause them to stick to it.
Insert the new charcoal filters deep
enough in the holder to ensure that
they do not protrude over the edge of
the holder.
65
Cleaning and care
Remove both charcoal filters and
place the new filters with the sur-
rounding edge pointing downwards in
the holder.
Place the holder in the middle of the
protective strip at the back of any ad-
justable shelf so that it clicks into po-
sition.
Confirming that the ActiveAirCleanfil-
ter has been changed
Tap OK.
The symbol will go out and the
counter will be reset.
Cleaning the door seal
Risk of damage as a result of in-
correct cleaning.
If you treat the door seal with oils or
grease, it can become porous.
Do not use any oils or grease on the
door seal.
The door seal should be cleaned regu-
larly with clean water, and then wiped
dry with a soft cloth.
Cleaning the ventilation open-
ings
The ventilation openings should be
cleaned on a regular basis with a
feather duster or vacuum cleaner (you
could use a Miele vacuum cleaner
dusting brush, for example).
After cleaning
Replace all shelves and accessories in
the refrigeration appliance.
Switch the refrigeration appliance
back on, if necessary.
Switch the fridge zone cleaning
mode off again, if necessary.
Switch the SuperCool function on
for a while so that the fridge zone can
cool down quickly.
Place food in the fridge zone.
Switch the SuperCool function off
once food and drinks are sufficiently
chilled.
Close the appliance door(s).
66
Troubleshooting
Many malfunctions and faults can be easily remedied. You can save time and
money in many cases, as you do not need to contact Customer Service.
More information to help you remedy faults yourself can be found at
www.miele.co.uk/support/customer-assistance.
To prevent unnecessary loss of temperature it is advisable not to open the door
while waiting for the appliance to be serviced.
Other problems
Problem Cause and remedy
The refrigeration appli-
ance is not cooling.
The refrigeration appliance has not been switched on.
Switch the refrigeration appliance on.
The mains plug is not inserted in the socket correctly
or the plug connector is not inserted into the socket at
the back of the appliance correctly.
Insert the mains plug into the mains socket and the
plug connector into the appliance socket correctly
and switch on.
The mains fuse has tripped. There could be a fault
with the refrigeration appliance, the household elec-
trical wiring or another electrical appliance.
Contact a qualified electrician or the Miele Cus-
tomer Service Department.
The compressor runs
continuously.
This is not a fault. To save energy, the compressor
runs at a lower speed when less cooling is required.
This increases the compressor running time.
The compressor is
switching on more fre-
quently and for longer
periods of time. The
temperature in the refri-
geration appliance is too
low.
The appliance door has been opened frequently. Or
large amounts of fresh food have been placed in the
appliance.
Only open the appliance door when necessary and
for as short a time as possible.
The appliance door does not close completely, and the
temperature inside the refrigeration appliance drops.
67
Troubleshooting
Problem Cause and remedy
Check that the appliance doors are seated correctly
and use the screws in the hinges to adjust them.
The appliance door is not properly closed. If a thick
layer of ice has already formed, this will affect cooling.
This will increase energy consumption.
Always close the appliance door fully.
Defrost the refrigeration appliance if necessary and
clean it.
The ambient temperature is too high. The higher the
ambient temperature, the longer the compressor runs.
See the information in “Installation – Installation
site”.
The ventilation openings are covered or dusty.
Do not block the ventilation openings.
Dust the ventilation openings regularly.
Built-in appliances: the refrigeration appliance was not
properly installed in the niche.
Install the refrigeration appliance in the niche as de-
scribed in the installation instructions.
The temperature in the
refrigeration appliance is
too low.
The temperature setting in the refrigeration appliance
is too low.
Correct the temperature setting.
The SuperCool function is still switched on.
You can switch off the SuperCool function earlier
to save energy.
The temperature in the
refrigeration appliance is
too high. The frozen food
(depending on the
model) could defrost.
This is not a fault. The temperature setting is too high.
Correct the temperature setting.
Check the temperature again after 24hours.
The ambient temperature is too low for this refrigera-
tion appliance. If the ambient temperature is too low,
the compressor will run less frequently. The temperat-
ure in the refrigeration appliance is rising.
See the information in “Installation – Installation
site”.
Increase the ambient temperature.
68
Troubleshooting
Problem Cause and remedy
Ice or condensation has
built up inside the refri-
geration appliance. The
appliance door may not
close correctly.
The door seal has come out of its groove.
Check that the door seal is correctly positioned in
the groove.
The door seal is damaged.
Check whether the door seal is damaged.
The door seal is dam-
aged or needs to be re-
placed.
No tools are required to change the door seal.
Change the door seal. A replacement is available
from Miele or from specialist retailers.
The food is affected by
the setting in the hu-
midity-controlled com-
partment.
There is too much condensate in the humidity-con-
trolled compartment.
Wipe off any condensate with a cloth.
Place a rack or similar item in the compartment so
that excess moisture can drain away.
Open the compartment cover by moving it to the
“low humidity” position.
Switch off the humidifier (depending on the
model).
There is no audible alarm
even though the door
has been open for a long
time.
This is not a fault. The alarm has been switched off in
Settings mode. If you want to switch the audible alarm
back on again:
Tap OK.
will appear in the display.
Use the or sensor control to scroll to the
symbol.
Tap OK.
Use the or sensor control to scroll to the
symbol.
Tap OK.
Use the and sensor controls to select the
volume you want for alarms and buzzers.
Tap OK.
When the alarms and buzzers are switched on, will
appear.
69
Troubleshooting
Display warnings
Message Cause and remedy
The symbol lights up
on the start display; the
refrigeration appliance
does not get cold even
though the controls and
the interior lighting are
working.
Demo mode has been switched on.
Tap the symbol.
Tap the symbol.
Swipe left or right until the symbol is shown in the
middle.
Tap the symbol.
After demo mode has been switched off, the refri-
geration appliance shuts down and must be switched
on again.
is lit up on the dis-
play and the appliance
cannot be used.
The Cleaning mode function is still switched on.
Switch the Cleaning mode function off again by tap-
ping on on the start display.
Tap again.
When Cleaning mode is switched off, the symbol
will light up white.
The refrigeration appliance will start cooling again.
Nothing is visible in the
display. The display is
completely blank.
Sabbath mode is switched on. The interior lighting
is switched off and the refrigeration appliance is
cooling.
Tap the black display.
The symbol will appear in the display.
Tap the symbol.
The symbol will light up orange.
Tap the symbol again.
When Sabbath mode is switched off, the symbol
will light up white.
Energy-saving mode is switched on: if you do not in-
teract with the display for a certain period of time, it
switches to energy-saving mode and goes dark.
The symbol is lit up on
the display and the refri-
geration appliance can-
not be used.
The lock function has been activated.
Unlock the refrigeration appliance temporarily or
switch the lock function off completely.
70
Troubleshooting
Message Cause and remedy
Automatic door opening
is activated.
will light
up red in the display and
an alarm will also sound.
The alarm has activated as the automatic door open-
ing motor has overheated.
Wait for a short while and allow the motor to cool
down.
Move the door manually.
Automatic door opening
is activated.
will light
up yellow in the display
and an alarm will also
sound.
An obstruction is blocking the movement of the door.
Remove the obstruction.
Move the door manually.
The door hinge mechanism is blocked.
Do not move the door against the motorised move-
ment. This can damage the door hinges.
Contact the Miele Customer Service Department.
The symbol lights up
on the start display and
a buzzer also sounds.
The charcoal filter change indicator on the start dis-
play reminds you that the charcoal filter needs to be
changed.
Replace the charcoal filter in the holder (see “Clean-
ing and care – Replacing the charcoal filters (op-
tional accessories)”) and touch the symbol on
the display to confirm that you have changed the
charcoal filter.
The symbol will go out on the start display.
will light up yellow in
the display, an alarm will
also sound and the in-
terior lighting will flash.
The door alarm has been activated.
ActiveDoor is not activated.
Touch
in the display.
The alarm will stop, the
symbol will go out and the
interior lighting will light up again constantly.
Close the appliance door.
71
Troubleshooting
Message Cause and remedy
The symbol lights up
red in the display and a
fault code F with num-
bers may appear. An
alarm also sounds.
There is a fault.
Tap the symbol on the display to switch the
alarm off.
Contact the Miele Customer Service Department.
To report the fault, you need the fault code and also
the model identifier and serial number of your refriger-
ation appliance. You can access this information on
the display:
Tap the symbol on the display.
The appliance data required will be shown on the dis-
play.
Confirm with the symbol to exit the information
display and the fault code will be shown again on the
display.
The refrigeration appliance can be switched off dir-
ectly from the fault message display.
Problems with automatic door opening
Problem Cause and remedy
The door is changing
speed as it opens.
This is not a fault. The speed of the inner door can
change based on its load.
will appear in the dis-
play. The door opening
angle cannot be saved.
The selected door opening angle is too small.
Select a door opening angle of at least 70°. A door
opening angle of 90° is ideal to ensure the drawers
can be pulled out without any problems.
72
Troubleshooting
Problem Cause and remedy
The appliance door is
not responding to the
knocking signal.
The knocking function is not activated.
Activate automatic door opening (see “Automatic
door opening (ActiveDoor)
A
” in “Selecting further
settings”).
Knocking is not hard enough.
Increase the sensitivity of the knock sensor (see
“Automatic door opening (ActiveDoor)” in “Guide to
the appliance”).
The door opening force is too high.
Open the appliance door and install the spacer sup-
plied at the side.
Holiday mode is activated. To save energy, automatic
door opening is deactivated.
Open the appliance door by hand.
As soon as Holiday mode is deactivated, automatic
door opening will be reactivated.
The appliance door is
not responding to voice
commands.
Automatic door opening is not activated.
Activate automatic door opening (see “Automatic
door opening (ActiveDoor)
A
” in “Selecting further
settings”).
The voice assistant is not set up.
Configure the setting in the Miele app.
The door opening force is too high.
Open the appliance door and install the spacer sup-
plied at the side.
Holiday mode is activated. To save energy, automatic
door opening is deactivated.
Open the appliance door by hand.
As soon as Holiday mode is deactivated, automatic
door opening will be reactivated.
73
Troubleshooting
Problems with the humidifier
Problem Cause and remedy
The humidifier is not
supplying moisture to
the food in the
PerfectFresh Active zone
The humidifier is not switched on.
Tap the symbol in Settings mode.
The compartment cover has been pulled forwards to
the “Humidity not increased” setting.
Push the compartment cover backwards so that the
“Increased humidity” setting is selected.
There is not enough water in the water container.
Fill the water container.
The water container is not fitted correctly.
Insert the water container, making sure it clicks into
position correctly.
There is dirt in front of the humidifier.
Clean the humidifier and the water container.
74
Troubleshooting
Interior lighting
Risk of electric shock due to exposed, live electrical components.
When removing the lighting cover, there is a risk of coming into contact with live
electrical components.
Do not remove the lighting cover. The LED lighting may only be repaired or re-
placed by the Miele Customer Service Department.
Risk of injury from LED lighting.
This lighting corresponds to risk group RG2. If the cover is defective, there is a
risk of eye injury.
If the lighting cover is defective, do not look from a close range directly into the
lighting with optical instruments (e.g. magnifying glass or similar).
Problem Cause and remedy
The interior lighting is
not working.
The refrigeration appliance has not been switched on.
Switch the refrigeration appliance on.
Sabbath mode is switched on: the display is dark
and the refrigeration appliance is cooling.
Tap the black display.
The symbol will appear in the display.
Tap the symbol.
The symbol will light up orange.
Tap the symbol in Settings mode.
When Sabbath mode is switched off, the symbol
will light up white.
To avoid overheating, the interior lighting switches it-
self off automatically after approx. 15minutes if the
appliance door is left open. If this is not the case, then
there is a fault.
Contact the Miele Customer Service Department.
75
Troubleshooting
Problem Cause and remedy
The LED lighting on one
of the adjustable shelves
is not working.
The shelf has not been positioned correctly on the
shelf supports.
Check that the shelf is positioned correctly on the
shelf supports. The shelf has metal contacts at the
front left corner which supply power to the LED
lighting.
Push the shelf in until it clicks into position.
The LED lighting on the stainless steel trim is faulty.
Replace the stainless steel trim with LED lighting. A
replacement is available from the Miele Customer
Service Department.
The LED lighting is not
working on any of the
shelves.
Liquid has been spilt onto the LED lighting on one of
the shelves or into the contact openings on the left-
hand shelf supports.
The safety switch-off mechanism has switched off the
LED lighting on all the shelves.
Wipe the stainless steel trim with LED lighting with
a damp cloth and dry it or leave it outside the refri-
geration appliance to dry.
Make sure that the contacts are clean and dry be-
fore replacing the shelves with lighting.
Push the shelf in until it clicks into position.
Close the appliance door.
The interior lighting will come on when the door is
opened again.
If this is not the case, then there is a fault.
Call the Miele Customer Service Department.
The interior lighting is
pulsating.
This is not a fault. The door alarm has been activated.
76
Troubleshooting
Noises
The refrigeration appliance is producing various noises during operation.
If the cooling performance is low, the refrigeration appliance will conserve energy
but operate for longer. The volume will be lower.
Food will be chilled faster if the cooling performance is high.
The volume will be higher.
Normal
noises
What is causing the noises?
Hissing Refrigerant is being injected into the cooling circuit.
Bubbling, gurgling,
splashing
Refrigerant is circulating through the pipes.
Humming The refrigeration appliance is cooling.
Clicking The thermostat is switching the compressor on or off.
Humming, whirring The fan is running.
The automatic door opener (depending on the model) is
opening or closing the appliance door.
Cracking Material in the refrigeration appliance is expanding.
Rattling Valves or flaps are active.
Buzzing (refrigeration
appliances with water
container)
Water is being pumped out of the water container.
Slurping (refrigeration
appliances with soft-
close mechanism)
The appliance door with soft-close mechanism is being
opened or closed.
Please bear in mind that a certain amount of noise is unavoidable (from the com-
pressor and the refrigerant circulating through the cooling circuit).
77
Troubleshooting
Noises Cause and remedy
Vibrating, rattling,
clinking
The refrigeration appliance is uneven. Use a level to
check and adjust the alignment of the refrigeration appli-
ance. The refrigeration appliance is aligned by raising or
lowering the adjustable feet (depending on the model)
underneath it.
For built-in appliances (depending on the model): For
niches of 140cm and more: place the stabilising rods
supplied underneath the appliance base.
The refrigeration appliance is touching another appliance
or piece of furniture. Move it away.
Drawers, baskets or shelves are jiggling or are stuck.
Check all removable items and refit them correctly.
Bottles or containers are touching. Separate bottles or
containers slightly.
The transport cable clips (depending on the model) are
hanging loose at the back of the appliance. Remove the
transport cable clips.
78
Service
Information to help you rectify faults
yourself and about Miele spare parts
can be found at www.miele.com/ser-
vice.
Contact in the event of a fault
In the event of a fault which you cannot
remedy yourself, please contact your
Miele dealer or Miele Customer Service.
You can book a Miele Customer Ser-
vice call-out online at www.miele.com/
service.
Contact information for Miele Cus-
tomer Service can be found at the end
of this document.
Please quote the model identifier and
serial number of your appliance (SN)
when contacting Miele Customer Ser-
vice. Both numbers can be found on the
data plate inside the refrigeration appli-
ance or, depending on the model, in
Settings mode under Information.
EPREL database
Since 1 March 2021, information on en-
ergy labelling and ecodesign require-
ments has been available in the
European Product Database (EPREL).
You can find the product database at
the following link https://
eprel.ec.europa.eu/. You will be asked to
enter the model identifier.
The model identifier can be found on the
data plate inside the refrigeration appli-
ance or, depending on the model, in
Settings mode under Information.
SN-ST
R600a:
XXXXXX
Nr. XX/ XXXXXXXXX.
XXX l
XXg
Warranty
For information on the appliance war-
ranty specific to your country please
contact Miele. See back cover for ad-
dress.
In the UK, your appliance warranty is
valid for 2 years from the date of pur-
chase. However, you must activate your
cover by calling 0330 160 6640 or re-
gistering online at www.miele.co.uk.
79
Information
EU Conformity declaration
Miele hereby declares that this fridge-freezer complies with Directive 2014/53/EU.
The complete text of the EU declaration of conformity is available from one of the
following internet addresses:
- Products, Download from www.miele.ie
- For service, information, operating instructions etc: go to
https://miele.ie.manuals and enter the name of the product or the serial number
Frequency range of the WiFi module 2.4000–2.4835GHz
Maximum transmission power of the
WiFi module
<100mW
UK Conformity declaration
Miele hereby declares that this fridge-freezer complies with UK Radio Equipment
Regulations 2017, as amended.
The complete text of the UK declaration of conformity is available from one of the
following internet addresses:
- Products, Download from www.miele.co.uk
- For service, information, operating instructions etc: go to https://miele.co.uk/
manuals and enter the name of the product or the serial number
Frequency band of the WiFi module 2.4000GHz – 2.4835GHz
Maximum transmitting power of the
WiFi module
<100mW
80
Information
ThisStatement of Compliance confirms this Miele product fully complies with the
Product Security and Telecommunications Infrastructure (Security Requirements
for Relevant Connectable Products) Regulations 2023.
1) Household Appliance –
2)
Manufactured by: Miele & Cie KG,
Carl Miele Street 29, 33332 Gutersloh Germany
Imported by and contact point: Miele Company Ltd, Fairacres, Marcham Road,
Abingdon, Oxon, OX14 ITW Great Britain
The defined support period at the time of first supply is 10 years
3)
To report vulnerabilities and cybersecurity issues please contact: [email protected]4)
5) Signature
Name: Paul Wright
Company Position: Head of Technical Management
Date of signature: 19th March 2024
Place of signature:
Abingdon, Oxfordshire
Freezer - 120002, 120003, 220009, 320001, 320002
Refrigerator - 110001, 110002, 210010, 310001, 310002,
310003
Fridge-freezer - 130001, 130002, 130003, 130004,
330001, 330002, 330005
Wine unit - 210007, 210011, 310004, 330004
Copyrights and licences
For the purpose of operating and controlling the communication module, Miele
uses proprietary or third-party software that is not covered by open source licens-
ing terms. This software/these software components are protected by copyright.
The copyrights held by Miele and third parties must be respected.
Furthermore, the communication module integrated in the appliance contains soft-
ware components which are distributed under open source licence conditions. The
open source components contained in the appliance along with the corresponding
copyright notices, copies of the licensing terms valid at the time and any further in-
formation can be accessed locally by IP via a web browser (http[s]://<IP address>/
Licenses). The liability and warranty arrangements for the open source licences dis-
played in this location only apply in relation to the respective rights holders.
81
United Kingdom
Miele Co. Ltd., Fairacres, Marcham Road, Abingdon, Oxon, OX14 1TW
Tel: 0330 160 6600, Internet: www.miele.co.uk, E-mail: [email protected]
Australia
Miele Australia Pty. Ltd.
ACN 005 635 398
ABN 96 005 635 398
Level 4, 141 Camberwell Road
Hawthorn East, VIC 3123
Tel: 1300 464 353
E-mail: [email protected]
Internet: www.miele.com.au
Miele Electrical Appliances Co. Ltd.
No. 82, Shimenyi Road, JingAn District
Shanghai, China, P.R.C
Post Code: 200040
Phone: +86 21 6157 3500
Fax: +86 21 6157 3511
E-mail: info@miele.cn
Internet: www.miele.cn
China Mainland
Miele (Hong Kong) Ltd.
41/F - 4101, Manhattan Place
23 Wang Tai Road
Kowloon Bay, Hong Kong
Tel: (852) 2610 1025
Fax: (852) 3579 1404
E-mail:
Website: www.miele.hk
Hong Kong, China
Miele India Pvt. Ltd.
1st Floor, Copia Corporate Suites,
Commercial Plot 9, Mathura Road,
Jasola, New Delhi - 110025
E-mail: customercare@miele.in
Website: www.miele.in
India
Miele Ireland Ltd.
2024 Bianconi Avenue
Citywest Business Campus
Dublin 24
Tel: (01) 461 07 10
Fax: (01) 461 07 97
E-mail: [email protected]
Internet: www.miele.ie
Ireland
Malaysia
Miele Sdn Bhd
Suite 12-2, Level 12
Menara Sapura Kencana
Petroleum
Solaris Dutamas No. 1
Jalan Dutamas 1
50480 Kuala Lumpur, Malaysia
Phone: +603-6209-0288
Fax: +603-6205-3768
Miele New Zealand Limited
IRD 98 463 631
8 College Hill
Freemans Bay, Auckland 1011
Tel: 0800 464 353
Internet: www.miele.co.nz
New Zealand
Miele Pte. Ltd.
29 Media Circle
#11-04 ALICE@Mediapolis
Singapore 138565
Tel: +65 6735 1191
Fax: +65 6735 1161
E-mail: [email protected]
Internet: www.miele.sg
Singapore
Miele (Pty) Ltd.
63 Peter Place, Bryanston 2194
Tel: (011) 875 9000
Fax: (011) 875 9035
E-mail: [email protected]
Internet: www.miele.co.za
South Africa
Miele Appliances Ltd.
Showroom 1, Eiffel 1 Building
P.O. Box 114782 - Dubai
Tel. +971 4 3044 999
Fax. +971 4 3418 852
800-MIELE (64353)
E-mail: [email protected]
Website: www.miele.ae
United Arab Emirates
Manufacturer: Miele & Cie. KG, Carl-Miele-Straße 29, 33332 Gütersloh, Germany
Thailand
Miele Appliances Ltd.
BHIRAJ TOWER at EmQuartier
43rd Floor Unit 4301-4303
689 Sukhumvit Road
North Klongton Sub-District
Vadhana District
Bangkok 10110, Thailand
Sheikh Zayed Road, Umm Al Sheif
E-mail: customercare@miele.co.nz
P.O. Box 69434, Bryanston 2021
M.-Nr. 12 583 990 / 05 / 002en-GB
K 7797 ...
