
English
EN
User manual
*
PL62X PL62X-EU PL62X-AUS PL62X-AS PL62X-100 PL62X-120
230 V
50 Hz
230 V
50 Hz
240 V
50 Hz
220 V
50/60 Hz
100 V
50/60 Hz
120 V
60 Hz
E+F E+F I G B B
The above information is valid for all versions: stainless steel and any colored version.

MaraX - PL62X
2
THANK YOU FOR CHOOSING
A LELIT PRODUCT
Register your product on
care.lelit.com
Download the complete guide
to get the most of your coffee machine PL62X*
and visit our LELIT YouTube channel
for insights, tutorials, tips and tricks.
Save the box and
all the packaging material!
LELIT has studied the external and internal
packaging of your coffee machine to help you
re-use it in case of maintenance or repair need.

English
3
EN
Index
1. Daily cleaning 4
2. Weekly cleaning 5
3. Annual cleaning 6
4. Product overview 8
5. Factory settings 8
6. Equipment box 9
7. Packing 10
8. First start-up 10
9. How to install the water softener lter 11
10. Espresso and coffee 12
11. Steam and hot water 13
12. Stand-by mode 13
13. Limescale prevention 14
14. Lights and states of the machine 15
15. Warranty terms 16
ATTENTION:
Read the safety notes carefully before using
this product.

MaraX - PL62X
4
1. Daily cleaning
1.1 1.2 1.3
Note. For an optimal result we suggest you use our kit PLA9101 (not
included) that contains a microber cloth with embroidered LELIT logo, a paint-
brush with bristles in natural bres and a brush with nylon bristles.
General cleaning. Use a soft cloth, preferably in microber, and moisten it with
tap water to clean the stainless steel appliance body of the machine (Pic 1.1).
Group cleaning. After each extraction empty the coffee lter, wash the lter-
holder (G) and the relative lter with tap water and use the brush (I) to eliminate
the coffee residues from the group gasket (Pic 1.2).
Steam wand cleaning. After frothing the milk, clean the nozzle of the steam
wand (7) using a soft cloth and dispense a small quantity of steam to eliminate
every possible milk residues in the holes (Pic 1.3).
Drip tray cleaning. The drip tray (17) should be hand-washed with neutral soap
and warm water to remove any build-up of coffee scum or mouldy coffee resi-
dues. This should be done daily to avoid bad smells and bacteria.

English
5
EN
2. Weekly cleaning
Note. In the equipment box you’ll nd the detergents (F) for the rst
cleaning cycle of the machine. Afterwards, we suggest you use our accessories
PLA9201 and PLA9203 (not included).
Filters and lterholder cleaning. It’s necessary to clean the lterholder to
eliminate the coffee oils that may affect the taste of your drinks negatively. Place
a jug under the hot water wand (15), turn the knob (12) anti-clockwise and take
out about 1 l of water.
Insert the lterholder (G) and the used lters into the jug but pay attention not to
immerse the lterholder handle (Pic. 2.1). Add 2 bags of detergent powder (F or
PLA9201). After 15 minutes, empty the jug and rinse the lterholder (G) and the
lters with plenty of tap water.
2.1 2.2 2.3
10x10”
min
15
Backushing. Insert the blind lter (C) into the lterholder and pour 1 bag of
detergent powder (F or PLA9201) into the lter. Insert the lterholder (G) in the
group head (13) and lift the lever (14) for 10 seconds. Stop the function by
lowering the lever completely and wait for 10 seconds. Repeat the procedure 10
times (Pic 2.2).
Remove the lterholder (G) from the group and rinse it with hot water from the
brewing group (Pic 2.3).
Re-insert the lterholder (G) in the group head and repeat the previous operation
5 times for 10 seconds each time, without detergent powder.
Remove the lterholder (G) and take out the blind lter (C). Empty the drip tray (17) and
rinse the lterholder (G), the lters and the tray (17) with plenty of tap water.

MaraX - PL62X
6
2.4
10x5”
Steam wand cleaning. Fill a jug with 500 ml of cold
water, add the content of 1 bottle of detergent liquid
(F or PLA9203) and immerse the steam wand (7) in
this solution.
Open the knob (3) and dispense steam for 5
seconds. Stop the function and wait for 5 seconds.
Repeat the operation 10 times (Pic 2.4).
Repeat the entire procedure using 1 l of fresh water
to rinse the steam wand (7) properly.
Water tank cleaning. Cleaning the water tank (10)
will remove build-up of limescale. Keeping fresh
water in the tank will minimize build-up of microorganisms. It is recommended
to change the water in the tank frequently in order to keep the tank clean and
ensure great tasting coffee. If your machine has not been used for a while, you
need to empty and dry the tank. Simply remove the tank cover (1), pull the tank
out and hand-wash it with water and neutral soap, using a vertical brush and
making sure the whole surface has been cleaned. Finally, rinse thoroughly, ll
it with fresh water and carefully dry the external surface of the water tank before
inserting it back into the machine.
3. Annual cleaning
The descaling of the hydraulic circuit of the machine must be done every year to
ensure longevity and constant performances. The state of the machine needs to
be checked previously by your reseller/specialized technician and the descaling
operation must be done by a specialized technician to avoid ruining the internal
components of the machine.

English
7
EN
in the
equipment box
PIC. 4
1
1 11 17
11
17
2
10
12
13
14
15
16
3
4
5
6
7
8
9
The data and images shown may undergo variations without notice
in order to improve the performance of the machine.

MaraX - PL62X
8
4. Product overview
5. Factory settings
1. Water tank cover
2. Hot surface with grate for cups
3. Steam dispensing knob
4. Machine ready pilot light
5. Full water tank pilot light
6. Manometer for steam and pump
pressure during extraction
7. Multi-directional, anti-burn
steam wand
8. ON/OFF main switch
9. Temperature mode switch
10. Water tank (2.6 l)
11. Grate for hot surface
12. Hot water dispensing knob
13. Brewing group
14. Brewing group lever
15. Multi-directional, anti-burn
hot water wand
16. Xmode switch
17. Removable drip tray,
complete with grate
Xmode switch (16)
Xmode Steam (pre-set value)
Temperature mode (9)
Warm (pre-set value)
Stand by:
ON
Water softener lter:
Not inserted
To use the machine with different settings, download the extended guide. The
complete guide contains the instructions on how to set other functioning proles.

English
9
EN
6. Equipment box
A. 1 dose (9-11 g) coffee lter
B. 2 doses (18-21 g) coffee lter
C. Blind lter for backushing
D. Tamper
E. Riser for espresso cups
F. First cleaning kit (with 3
detergent powder single-dose
bags and 1 single-dose bottle)
G. Filterholder complete with
2 doses (14-18 g) coffee lter
H. LELIT 35 l water lter
I. Brush for group head cleaning
J. Plastic spoon for coffee powder
K. Power cord
E
D
G
H
I
K
J
A
B
C
F
Discover all the accessories and the necessary instruments to become a true barista.
Visit our website LELIT.COM

MaraX - PL62X
10
7. Packing
The packaging of your coffee machine has been studied and produced to be
re-used. Use the original box and all the packaging elements in case you need
to send the machine back to your reseller or to an authorized service centre,
for ordinary or extraordinary maintenance. The extended guide contains the
instructions to help you pack the machine easily.
8. First start-up
8.1 8.2 8.3
FRONT
30
sec
Attention. Remove the machine from its packing and follow the
instructions printed on the box.
Place the machine on a solid, at and dry surface and make sure the appliance
is stable.
From the equipment box, take out the drip tray (17), the grate (11), the cover (1)
and position them as indicated in Pic. 4.
Fill the water tank (10) with room temperature water up to the indicated maxi-
mum level and insert it in its seating (Pic 8.1).
Use the power cord (K) to connect the machine to the electrical mains and turn
ON the machine by pressing the ON/OFF (8) switch. If the water tank (10) is full
of water and properly inserted in its seating, the pilot light (5) goes ON (Pic 8.2).
The hydraulic circuit will need maximum 4 minutes from the 1st turn on to get
lled with water. Once the waiting time is over, the pilot light (4) will start ashing.
Lift the group lever (14) completely (Pic 8.3). The brewing group (13) will start

English
11
dispensing water (within 30 seconds). Let the water come out for about 30
seconds and then return the group lever to its initial position.
Now the hydraulic circuit is lled up. The machine will start heating the water to
reach the pre-set values. This operation requires maximum 24 minutes: the pilot
light (5) remains rmly on, while the pilot light (4) ashes.
The machine is ready for use when the 2 pilot lights (4 and 5) and the lighted
frame of the ON/OFF (8) switch are rmly on.
Attention. During the heating phase, a small quantity of water will drain
in the tray (17). This is normal and conrms the machine correct functioning
(functions check).
9. How to install the water
softener filter
9.1 9.2 9.3
1
2
min
3
Before installing the water softener lter (H) in the water tank (10), immerse the
water softener lter in a jug full of water for about 3 minutes, to eliminate the air
inside the lter that may cause a machine malfunction (Pic 9.1).
Pull out the water tank (10) and remove the black rubber support placed on the
bottom of the tank. Insert the water softener lter (H) in the bigger hole of the
rubber support, remove the charge tube from the small plastic lter and x it on
the nozzle of the water softener lter (H) (Pic 9.2).
Position the support in its seating on the bottom of the tank (Pic 9.3), ll the tank
(10) with water and insert the tank (10) in its seating.

MaraX - PL62X
12
10. Espresso and coffee
10.1 10.2 10.3
1
OK
2
Choose your coffee lter, insert it into the lterholder (G) and ll it with the quan-
tity of ground coffee suggested on the lter. Use the tamper (D) to press the
coffee powder in the lterholder (G). Fix the lterholder (G) into the brewing
group (13) and make sure the handle is aligned with padlock symbol present on
the group (Pic 10.1).
Place the cup/s under the coffee slide and lift the group lever (14) to start the
coffee extraction (Pic 10.2).
During the extraction phase, the lighted frame of the ON/OFF switch (8) ashes
to indicate that the pump works. Return the group lever (14) to its initial position
to stop the extraction (Pic 10.3).
Take out the lterholder (G) and empty the lter after every coffee extraction.
Note. During the normal functioning the pilot lights of the machine may
ash or go off to indicate various states of the machine. See the chapter 14
“Pilot lights and states of the machine” for more details.
Note. We suggest you leave the lterholder (G) inserted into the brew-
ing group (13) to help harmonize the temperature between the group and the
lterholder complete of the lter.
Attention. Do not remove or loosen the lterholder (G) from the brewing
group (13) during the coffee extraction to avoid burn risks caused by hot water leaks.

English
13
11. Steam and hot water
To obtain an optimal performance of the machine, lift the group lever (14) com-
pletely and return it to its initial position about 30 seconds before using the steam
wand or the hot water wand (7 or 15).
11.1
Turn the knobs (3 or 12) anticlockwise to dispense
steam or hot water (Pic 11.1).
Vary the rotation of the knob to adjust the steam or
hot water quantity/intensity.
Turn the knobs (3 or 12) clockwise to stop the func-
tion.
12. Stand-by mode
12.1 12.2 12.3
30
min
After 30 minutes of inactivity, the machine will go automatically in stand-by mode
(Pic 12.1).
The lighted frame of the ON/OFF switch (8) ashes while the pilot lights (4 and
5) remain rmly off (Pic 12.2).
To re-start the machine, you must lift the group lever (14) completely and return
it to its initial position (Pic 12.3).
Wait until all the pilot lights are rmly on before using the machine.

MaraX - PL62X
14
Note. The Stand-by function can be disabled. For more details download
the extended guide.
13. Limescale prevention
13.1
To prevent limescale deposits and grant a better re-
sult in the cup, use the water lter (H). The lter
found in the equipment box has an autonomy tested
for 35 litres of water.
Use the slides put on the handles of the water tank
(10) to remember the complete llings of the tank
and replace the water softener lter once exhausted
(Pic 13.1).
Note. The water softener lter must be replaced every 14 complete llings,
or after 4 months of use. If the machine remains unused for 1 month, the water
softener lter must be replaced with a new one.
Note. See chapter 9 “How to install the water softener lter” to replace the
lter correctly.

English
15
EN
14. Lights and states of the machine
State of the machine
Machine in heating phase
Wait until the machine is ready for use
Water tank is missing or water tank is
empty
Fill the water tank (10) with water and insert
it in its seating
Machine ready for use
You can start using the machine
Machine in Stand-by mode
Lift the group lever (14) completely and
return it in its initial position to activate the
machine. Wait until all the pilot lights are
rmly on before using the machine.
Temperature sensor NTC1 disconnected
or damaged
Contact the service centre
Temperature sensor NTC2 disconnected
or damaged
Contact the service centre
Boiler lling phase has exceeded the
maximum time
Check the correct position of the water
tank (10) and remove eventual blockages.
Re-start the machine with the main switch.
If the problem persists, contact the service
centre.
Pilot light is on Pilot light ashes Pilot light is off

MaraX - PL62X
16
15. Warranty terms
LIMITED GUARANTEE
Depending on the place of purchase either the seller or LELIT guarantee this
product for domestic use in specied territories for a limited time from the date of
purchase against defects caused by faulty workmanship and materials.
During this guarantee period either the seller or LELIT will repair, replace or
refund any defective product at their sole discretion. All legal warranty rights
under applicable national legislation will be respected and will not be impaired
by any written guarantee.
For Australian consumers, this product comes with guarantees that cannot be
excluded under the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and compensation for any other reasonably
foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure.
Important requirements as well as instructions on how to make a claim can be
found on the LELIT website in the full warranty terms and conditions.

English
17
EN
IMPORTANT INFORMATION
For the correct disposal of the product in accordance with
EU DIRECTIVE 2012/19/EC and with Legislative Decree
no. 151 of 25 July 2005. At the end of its working life, the
product must not be disposed of as urban waste. It must be
taken to a special authorised differential waste collection
centre or to a dealer providing this service. Disposing of a
household appliance separately avoids possible negative
consequences for the environment and health caused by
improper disposal and enables recovery of the materials it
contains, with signicant savings in energy and resources.
The product is marked with a crossed-out wheelie bin as a
reminder of the need to dispose of household appliances
separately.
EC DECLARATION OF CONFORMITY
LELIT srl a socio unico declares under its own responsibility
that the product: Coffee machine type: PL62X to which this
declaration relates conforms to the following standards:
EN 60335-2-15:2016 + A11:2018 + A1:2021 + A2:2021
+ A12:2021;
EN 60335-1:2012 + AC:2014 + A11:2014 + A13:2017
+ A1:2019 + A14:2019 + A2:2019 + A15:2021;
EN 62233:2008; CISPR 14-1; CISPR 14-2; EN 61000-3-2;
EN 61000-3-3; EN 55014-1:2017; EN 55014-2:2015;
EN 50564:2011.
pursuant to directives:
2014/35/EC; 2011/65/EU; 1907/2006/EU
NB: This declaration is null and void should the machine be
modied without our specic authorisation.
Castegnato, 04/07/2022
Emanuele Epis - Legal Representative

LELIT.COM
EN/7800052
©2023 LELIT srl
All Rights Reserved
