ROVSUN SF105-18G 27'' High 1400W 120V Electric Fireplace User Manual

SF105-18G

MADE IN CHINA

ELECTRIC FIREPLACE

TableofContents

Safety Information..................................................................................3

Pre-installation.......................................................................................6

Assembly......................................................................................7

Operation.........................................................................................8

Using the Remote Control....................................................................11

Care and Maintenance..........................................................................12

Troubleshooting....................................................................................13

SafetyInformation

IMPORTANTSAFETYINFORMATION

PLEASEREADALLOFTHEINFORMATIONINTHISOPERATINGMANUAL,INCLUDING

ALLSAFETY,OPERATING,ANDMAINTENANCEINFORMATION.TOAVOIDTHE

POTENTIALRISKOFFIRE,ELECTRICSHOCK,ORINJURYTOPERSONS,

USERSSHOULDFOLLOWTHEDIRECTIONSANDWARNINGSINTHISMANUAL

1.Readallinstructionsbeforeusingthisheater.

2.Donotusethisheateroutdoors.

3.Thisheaterisnotintendedforuseinbathrooms,laundryareasandsimilarindoorlocations.Neverlocatethe

heaterwhereitmayfallintoabathtuborotherwatercontainer.

4.Donotrunthepowercordundercarpeting.Donotcoverthepowercordwiththrowrugs,runners,orthelike.

Arrangethepowercordawayfromtrafcareasandwhereitwillnotbetrippedover.

5.Todisconnecttheheater,turncontrolstooff,thenremovetheplugfromtheoutlet.

6.Connecttoproperlygroundedoutletsonly.Alwaysplugheatersdirectlyintoawalloutlet/receptacle.Never

usewithanextensioncordorrelocatablepowertap(outlet/powerstrip).

7.Topreventapossiblere,donotblockreboxairintakesortheexhaustinanymanner.Donotoperatethe

reboxonsoftsurfaces,likeabed,whereopeningsmaybecomeblocked.

8.Thereisathermostatlimiterinsidetheheater.Whentheinnertemperatureoverheatsorabnormalheating

occurs,thethermostatprotectivedevicecutsoffthepowersupplytoavoidreplacedamagedorriskofre.

9.Usethisheateronlyasdescribedinthismanual.Anyotherusenotrecommendedbythemanufacturermay

causere,electricalshock,orinjurytopersons.

SAVETHESEINSTRUCTIONS

WARNING

Therearenouserserviceablepartsinsidethereplace/heater,

Iftheunitappearstomalfunction,

turmtheunitoffandunplugtheunitfromthewallimmediately,andcontactCustomer.

WARNING

Thisheaterishotwheninuse.Toavoidburns,donotletbareskintouchhotsurfaces.

Ifprovided,usehandleswhenmovingthisheater,Keepcombustiblematerial,

suchasfurniture,pillows,bedding,papers,clothesandcurtains

atleast3f.t(0.9meters)fromthefrontoftheheaterandkeepthemawayfrom

thesidesandrear.

WARNING

Extremecautionisnecessarywhenanyheaterisusedbyornearchildrenorinvalids

andwhenevertheheaterisleftoperatingandunattended.

WARNING

Alwaysunplugtheheaterwhennotinuse.

WARNING

Donotoperateanyheaterwithadamagedcordorplugor

aftertheheatermalfunctions,hasbeendroppedordamagedinanymanner.

Returntheheatertoanauthorizedservicefacilityforexamination,

electricalormechanicaladjustment,orrepair.

WARNING

Donotinsertorallowforeignobjectstoenteranyventilationorexhaustopenings

asthismaycauseanelectricshockorre,ordamagetheheater.

WARNING

Aheaterhashotandarchingorsparkingpartsinside.

Donotuseinareaswheregasoline,paint,orammableliquidsareusedorstored.

CAUTION

Whiletheheaterisinuse,thetopcenterofthereplacecangethottothetouch,

andmaycauseseriousinjuryorburns.

Alwayssupervisesmallchildrenaroundthereplace/heater.

Donotplaceanyclothordecorationsovertheheateroutletofthereplace,

orotherwiseobstructtheheateroutletofthereplace,

asthismaycauseareandseriousinjurymayresult,

SafetyInformation(continued)

GROUNDINGINSTRUCTIONS

Thisproductmustbegrounded.Ifitshouldmalfunctionorbreakdown,groundingprovidesapathofleast

resistanceforelectriccurrenttoreducetheriskofelectricshock,Thisproductisequippedwithacordhaving

anequipment-groundingconductorandagroundingplug.Theplugmustbepluggedintoanappropriateoutlet

thatisproperlyinstalledandgroundedinaccordancewithalllocalcodesandordinances.

Thisheaterisforuseon120-voltcircuitsandhasagroundedplug.Anadapterisavailablefromyourlocal

electronicsstoreoronlinesupplierforconnectingthree-bladegrounding-typeplugstotwo-slotreceptacles.

Thegreengroundinglugextendingfromtheadaptermustbeconnectedtoapermanentground

suchasaproperlygroundedoutletbox.Theadaptershouldnotbeusedifathree-slotgroundedreceptacle

isavailable.

DANGER

Improperconnectionoftheequipment-groundingconductorcanresult

inariskofelectricshock.Checkwithaqualiedelectrician

orservicemanifyouareindoubtastowhethertheproductisproperlygrounded.

Donotmodifytheplugprovidedwiththeproduct.

Ifitwillnotttheoutlet,haveaproperoutletinstalledbyaqualiedelectrician.

Cover of Grounded Outlet Box

Grounding Pin

Adapter

Grounding Lug

Metal Screw

Cover of Grounded Outlet Box

Pre-installation

TECHNICAL SPECIFICATION

Model Number Description

19"*5.1"*17.5"

Dimensions(WxDxH)

Net Weight

Gross Weight

Power Rating

Voltage

Frequency

12.6 Ib

14.8 Ib

1400W

120V

60Hz

PACKAGE CONTENT

Fireplace Unit Remote Control Screw x5

Assembly

●STEP 1

Take out the unit from the box and layout all the spare parts for easy assembly. Make sure all small items

are not left in packaging materials.

NOTE:

Do not attempt to install the unit from the front of the mantel. It will not t.

●STEP 2



Carefully set the unit from the back of the mantel and center it in the opening.

Check the alignment and attach the unit of the mantel by inserting screws through the drilled holes

on the trim of the mantel.

Operation

●󵿎Identifyingthecontrolpanel



•Thecontrolpanelislocatedonthetoprightcornerofthereplace/heaterunit.

•Thecontrolpanelcontainsthedisplayunit(1),functionindicator(2),timerfunction(3),heatercontrol(4),

amescontrol(5),andmainpower(6).

•Thedisplayunit(1)displaysinformationabouttheamelevel,timer,andcurrenttemperature.

●󵿎Understandingthefunctionindicator

•Thefunctionindicator(2)hasthreesquareLEDS-red,green,andblue.TheredLEDindicatesthattheFahrenheit

temperatureheatingfunctionisrunning,thegreenLEDindicatesthattheCelsiustemperatureheatingfunction

isrunning,andtheblueLEDindicatesthatthetimerfunctionisengaged.

•TothebottomofthethreeLEDS,istheinfraredreceivermodulewhichcommunicateswiththeremotecontrol

tocontroltheheater.

Operation

●󵿎Usingthetimerfunction

Thetimerbutton(3)allowsyoutosettheamountoftimeyouwantthereplace/heatertorun.Thetimerbutton(3)

operatesboththeamesandtheheaterfunction.iftheheaterisoperatingwhenthetimerisset,thentheheater

isonthetimer.iftheamesareoperating,thenthetimerwillcontroltheames.ifboththeheaterandamesare

operatingwiththetimerset,thenthetimercontrolsboththeamesandtheheater.Pressingthebuttoninsequence

willsetthetimerforasetinterval.Thisintervalperiodisshowninthedisplay(1),inblue.Thesetintervals

aredisplayedinthistable.Thetimerintervalissetfromthetimetheintervalisselected.Thereisnoclockfunction

forturningtheheateroramesonoroffataspecictime.

●󵿎Usingtheheatercontrol

•Theheaterbutton(4)turnstheheateronoroff.Thereisnospeedsettingfortheheaterblower.lfyouputthe

heaterinastandbymode(turnoffbythemainpowerbutton6),theunitwillholdthesettingsinthememory.

Whenthepoweristurnedbackon,theheaterwillturnonatthesamesettings.

•Whentheheatingfunctionturnson,pressandholdtheheaterbutton(4)forvesecondstoentertemperature

adjustmentmode.TheLEDindicatorisred.Inadjustmentmode,thedisplayunit(1)ashes(intervalis0.5second).

Thereare22levelstochangeFahrenheittemperature72°F—73°F...82°F—ON—62F—63F...71F.

Afterthisisset,thedisplay(1)willashvetimesandexitfromsettingstatus.

Ifidle,thedisplayturnsoffafter10seconds.

•Withtheheateron,gentlypressandholdthemainpowerbuttonforvesecondstoentertemperature

convertingmode.TheLEDindicatorashesvetimesinredcolorthenchangestogreen.Inthisconvertingmode,

thedisplay(1)ashes(intervalis0.5second).Pressandholdtheheaterbutton(4)forvesecondstoenter

temperatureadjustmentmode.Thereare12levelstochangeCelsiustemperature

22C—23°c...27·C—ON—17C—18..21C.Afteriisset,thedisplay(1)ashesvetimes.Ifidle,thedisplayturnsoff

after10seconds.RepeatthesameprocesstoconvertCelsiustemperatureintoFahrenheittemperature.

ButtonPress

1stpress

2ndpress

3rdpress

4th press

5th press

6th press

7th press

8th press

TimerInterval Display

30Minutes

30

1Hour

2Hours

3Hours

4Hours

5Hours

6Hours

OFF

1h

2h

3h

4h

5h

6h

None

Operation

●󵿎Usingtheamecontrol

•Presstheamebutton(5)tosettheamesfordifferentlevelsofameheight.Theseamelevelsareshowninthe

display(1).Theamesettingsareasfollows:

ButtonPress

1stpress

2ndpress

3rdpress

4th press

FlameLevel Displayvalue

High

L3

Medium

Low

AllOff

L2

L1

None

FireplaceAppearance

FlamesHighest,LogsGlowHighest

FlamesMedium,LogsGlowMedium

FlamesLow,LogsGlowLow

FlamesOff,Logsoff

•Regardlessofthepreviousamesetting,whenpoweredoffbythemainpowerbutton(6),

theameswillcomeoninL3mode(High)whenyouturntheheateron.

•Whentheheaterfunctionturnson,theamelevelwillcyclethroughthe3differentlevelsettingscontinuously.

ButtonPress

1stpress

2ndpress

3rdpress

FlameLevel Displayvalue

High

L3

Medium

Low

L2

L1

FireplaceAppearance

FlamesHighest,LogsGlowHighest

FlamesMedium,LogsGlowMedium

FlamesLow,LogsGlowLow

●󵿎Usingthemainpowerbutton

•Pressthepowerbutton(6)toturnthereplace/heaterunitonandoft.

Pressthepowerbutton(6)oncetoturntheuniton.Pressagaintoturntheunitoff.

UsingtheRemoteControl

1.Non-rechargeablebatteriesarenottoberecharged.

2.Batteriesaretobeinsertedwiththecorrectpolarity.

3.Exhaustedbatteriesaretoberemovedfromtheproduct.

4.Alwayspurchasethecorrectsizeandgradeofbatterymostsuitable

fortheintendeduse.

5.Replaceallbatteriesofasetatthesametime..

6.Cleanthebatterycontactsandalsothoseofthedevicepriortobatteryinstallation.

7.Removebatteriesfromequipmentwhennotusedforanextendedperiodoftime.

WARNING

Donotingestbatteries.

NOTE:

Batterydisposal

Pleasealwaysdispose

ofbatteries atasuitable

recyclingpoint.

Flame Control

Heater Control

●󵿎Using the Remote control

The operation of the remote control buttons work the same as button on the control panel.

●󵾯Install the battery

For replacement batteries, use AAA batteries.

Press down and slide back cover off the battery compartment.

Insert two provided AAA batteries into the battery compartment making sure that the ends of the batteries

with the negative(-) symbols are against the springs in the battery compartment.

Replace the battery compartment cover, making sure it snaps into position.

Main Power

Time Control

Heater Down

Heater Up

Care and Maintenance

WARNING

Alwaysdisconnectfromthepowersupplybeforecleaningtheheater.

Firstturnoffthemain power.

Thenremovetheelectricalplugfromthewall outlet.

WARNING

Donotusethisreplaceinsertifanypartof ithasbeenunderwater.

Immediatelycallaqualied servicetechniciantoinspectthereboxand

replace anypartoftheelectricalsystemwhichhasbeenunderwater.

Theblowermotorandamemotorarepre-lubricatedforadurableusingtimeandneednofurtherlubrication

ormaintenance.Toremoveanyaccumulationofdustordebris,thesoftbrushattachmentofavacuumcleaner

shouldoccasionallybeusedtocleantheoutletgrilleofthefanheater.

● Useasoft,cleancloththatwillnotscratchthesurfacewhendusting.

● Useacleansoftclothdampenedwithwarmwatertocleanthereplacesurface.

D0NOTusehouseholdorabrasive cleaners,astheseproductsmaydamagethesurface.

● Whencleaningtheglassviewingscreenuseanon-abrasivedampclothwithliquidcleanerorsoftsoap

ifnecessary;Don NOTusecleaningpowdersoranyothersubstancewithabrasives

sincethesesubstanceswillscratchglass.

● Undernocircumstancesshouldthisproductbeoperatedwithabrokenorchippedglasspanel.

● Donotstrikeorslamtheglass.

● Intheeventthatyourapplianceisstainedorotherwisedamagedduringuse,werecommendthatyoucall

aprofessionaltoit.

● Whennotinusepleaseunplugthecordfromtheoutlettopreventanydamageoraccidents.

Troubleshooting

Problem

Solution

Checkthattheunitisfullypluggedinto

astandard120Voutlet.

Pressthepowerbuttononthecontrolpanel.

Theunitdoesnotturnon.

Theunitison,butthereisnoameeffect. Openthebackpanelstocheckiftheame

spindlehas fallenofffromthespindlemotor.

Thereisavisibleameeffect,buttheheater

doesnot continuetoblowwarmairafterrepeatedly

turningontheheater.

Turnon/offtheheaterbuttonseveraltimesto

makesure itisinthe“ON”position.

Theheaterdoesnotwork,butthepower

andheaterswitchesareinthe“ON”position.

Turnallswitchestothe“OFF”positionandunplug

the unitfromthewalloutletfor5minutes.

After5minutesplugtheunitbackintothewalloutlet,

andoperateas normal.

Makesurethatnoobjectsareblockingtheair

ventsonthetopandonthefrontofyourreplace.

Changetheremotebattery.

Operateremotetransmitterataslowmeasuredpace.

Presstheremotecontrolbuttonswithanevenmotion

andgentlepressure.

Repeatedlypressingbuttonsinrapidsuccessionmay

causethetransmittertomalfunction.

Standclosertoyourreplace.

Removeobjectsthatmayblockyourremotecontrol's

abilitytocommunicatewithyourreplace.

Remotecontrolisnotworking.

ROVSUN SF105-18G 27'' High 1400W 120V Electric Fireplace with Mantel & Remote

Product's Documents

User Manual

Specifications

ROVSUN SF105-18G Questions and Answers

Related Products

ROVSUN SF57B-17A00 20" High 1400W 120V Electric Fireplace Stove

ROVSUN SF413-23A 18" Wide 1400W 120V Electric Fireplace Insert Log with Remote & WiFi Control

ROVSUN HT1108 22" High 1500W 120V Electric Fireplace Stove Milky

ROVSUN HT1908DPRO 1500W 120V Electric Fireplace Heater with Remote & Timer

ROVSUN HT8006NB 1500W 120V Electric Heater with Remote Control Freestanding

ROVSUN HT8006NBW 1500W 120V Wall Mounted Electric Heater with Remote & Timer