MT10
FCC compliance statement
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not
cause harmful interference, and (2) this
device must accept any interference
including received interference that may
cause undesired operation.
The grantee is not responsible for any
changes or modifications not expressly
approved by the party responsible for
compliance. Such modifications could void
the user’s authority to operate the
equipment. Replacement of any transmitter
component (crystal, semiconductor, etc.) not
authorized by the FCC equipment
authorization for this radio could violate FCC
rules.
Note: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation.
If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
This radio complies with IEEE and ICNIRP
exposure limits for General Population /
Uncontrolled RF exposure environment at
operating duty factors of up to 50% and is
authorized by the FCC for General Population
/Uncontrolled Use Only. An appropriate
warning label is affixed to all units. In order
to comply with RF exposure requirements, a
minimum distance of 2.5 cm must be
maintained when held-to-face, and
body-worn operations are restricted to the
approved original accessories (belt
clip), a minimum distance of 0 cm. Do not
use this device when antenna shows obvious
damages.
WARNING: MODIFICATION OF THIS
DEVICE TO RECEIVE CELLULAR
RADIOTELEPHONE SERVICE SIGNALS IS
PROHIBITED UNDER FCC RULES AND
FEDERAL LAW.
CANADA LICENSING INFORMATION
This device contains licence-exempt
transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the following
two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference,
including interference that may cause
undesired operation of the device.
L’émetteur/récepteur exempt de licence
contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et
Développement économique Canada
applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux
conditions suivantes:
(1) L' appareil ne doit pas produire de
brouillage;
(2) L' appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage
est susceptible d' en compromettre le
fonctionnement.
This EUT is compliance with SAR for General
Population/Uncontrolled exposure limits in
ISED RSS-102 at operating duty cycle of up to
50% and had been tested in accordance with
the measurement methods and procedures
specified in IEC/IEEE 62209-1528. This
equipment should be installed and operated
with a minimum distance of 2.5 cm must be
maintained when held-to-face, and
body-worn operations are restricted to the
approved original accessories (belt clip), a
minimum distance of 0 cm.
Cet EUT est conforme aux limites
d'exposition contrôlées SAR de la norme
ISDE RSS-102 pour un cycle de service de
fonctionnement allant jusqu'à 50 % et a été
testé conformément aux méthodes et
procédures de mesure spécifiées dans la
norme IEC/IEEE 62209-1528. Cet
équipement doit être installé et utilisé à une
distance minimale de 2,5 cm lorsqu'il est
tenu face au visage et les opérations portées
sur le corps sont limitées aux accessoires
d'origine approuvés (clip de ceinture), à une
distance minimale de 0 cm.
This radio transmitter IC:36041-MT10 has
been approved by Innovation, Science and E
conomic Development Canada to operate wi
th the antenna types listed below, with the
maximum permissible gain indicated. Antenn
a types not included in this list that have a ga
in greater than the maximum gain indicated f
or any type listed are strictly prohibited for u
se with this device.
Cet émetteur radio IC:36041-MT10 a été
approuvé par Innovation, Sciences et Dévelo
ppement économique Canada pour fonction
ner avec les types d'antenne énumérés ci-de
ssous, avec le gain maximal admissible indiq
ué. Les types d'antenne non inclus dans cett
e liste qui ont un gain supérieur au gain maxi
mum indiqué pour tout type répertorié sont
strictement interdits pour une utilisation ave
c cet appareil.
