Remote control
PAIRING
Theremotecontrolcanonlybepairedwhenerror
codeE07isdisplayed.Thiscodeappearswhen
thesafetycordisnotconnectedtothetreadmill.
Topairtheremote:
01Insert2AAAbatteries
02Turnonthetreadmill.
03Removethesafetycordsothat
E07appearsonthedisplay.
04Within5secondsofremovingthe
safetycord,pressandholdthe
start/stopbuttonontheremote.
05Alongbeepconfrmssuccessfulpairing.
Oncepaired,theremoteremainsconnected.
Youdonotneedtorepeatthisprocessafter
switchingthetreadmilloffandonagain.
USE
Pause (PAUSE):Briefypressthepausebutton
whileyourtreadmillrunstopauseyoursession.
Mute button ( ): Briefypressthemutebuttonto
mutethebuzzer(thecontrolpanelwillshow“OFF”).
Briefypressitagaintoturnthebuzzerbackon
(thecontrolpanelwillshow“ON”).
Plus (+):Presstheplusbuttontoincreasethe
treadmill’sspeed.Pressitbriefyforaslowincrease
with0.1km/h,orkeepitpressedtocontinuously
increasethespeedwith0,5km/h.
Minus (–):Presstheminusbuttontodecreasethe
treadmill’sspeed.Pressitbriefyforaslowdecrease
with0.1km/h,orkeepitpressedtocontinuously
decreasethespeedwith0.5km/h.
Start/Stop: Start:Instandbymode,pressthestart/
stopbuttontostartyourtreadmill.Aftera3-second
countdown,thetreadmillstartsataspeedof1.0km/h.
Stop:Pressthestart/stopbuttonduringyour
sessiontostop.
Resume:Briefypressthestart/stopbutton
whileyourtreadmillispausedtoresumeyour
sessionataspeedof1.0km/h.
Incline ( ):Briefypresstheinclinebuttonto
increasetheinclineofyourtreadmillby1level.
Decline ( ):Briefypressthedeclinebuttonto
decreasetheinclineofyourtreadmillby1level.
Program/Mode (P/M):PresstheP/Mbutton
toscrollthroughthe12presetprograms(P1–P12).
Press⏯ (START/STOP)toselectaprogram.Each
programhasfxedtimeandspeedsettings
thatadjustautomatically.Youcanviewtheirdetails
onpage37.SetyourownworkouttargetinMode:
afterP12,pressP/MagaintoenterMode
(customsettings).InMode,youcansetyour
ownworkouttarget:
Time(default:30:00)
Distance
Calories(default:300)
PressP/MtoswitchbetweenTime,Distance,
orCalories.Usethe+/–buttonstoadjustthe
selectedvalue.PressSTART/STOPtobegin.
Speedandinclinecanbeadjustedmanually
atanytimeusingthe+/–buttons.
3 button (3):Directlysetsspeedto3.0km/h.6
button (6):Directlysetsspeedto6.0km/h.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.The device
has been evaluated to meet general RF exposure requirement. The device can
be used in portable exposure condition without restriction.
