
model no. 060-1963-8 | contact us 1.866.523.5218
IMPORTANT:
Read and follow all safety rules and operating
instructions before using this product.
Instruction
Manual
36 cm (14”) BRUSHLESS GRASS TRIMMER
3025736

model no. 060-1963-8 | contact us 1.866.523.5218model no. 060-1963-8 | contact us 1.866.523.5218
2

model no. 060-1963-8 | contact us 1.866.523.5218 model no. 060-1963-8 | contact us 1.866.523.5218
3
model no. 060-1963-8 | contact us 1.866.523.5218
Introduction 4
Safety Instructions 5
Symbols 8
Product Specications 9
Product Diagram 10
Assembly 11
Operation 13
Maintenance and Storage 18
Troubleshooting 19
Exploded View 20
Parts List 21
Warranty 22
Table of Contents

model no. 060-1963-8 | contact us 1.866.523.5218
4
Introduction
INTRODUCTION
Congratulations on your purchase of your new Yardworks
®
tool. It has been designed, engineered
and manufactured to give you the best possible dependability and performance.
Should you experience any problem you cannot easily remedy, please contact our Yardworks
®
customer service line at 1.866.523.5218.
PLEASE READ AND RETAIN THIS INSTRUCTION MANUAL. These instructions will enable you to
assemble and maintain your appliance properly. ALWAYS observe the “SAFETY RULES”.
The instruction manual was designed to conveniently help you get your purchase ready to use so
there’s less risk of damage and to provide you with enough information to get familiar with your prod-
uct’s controls and features so you can operate your product safely.
Please do not operate garden equipment near children. This could
lead to severe injury or death.
Model number:
Serial number:
Date of purchase (MM/DD/YYYY):
Notes:
Please read this manual carefully and make sure you understand the instructions
before using the machine.
SAFETY FIRST
CAUTION: The operation of lawn equipment can
result in foreign objects thrown into the eyes, which
can result in SEVERE EYE INJURY. ALWAYS wear
safety glasses or eye shields while operating your
lawn equipment or performing any adjustments or
repairs. We recommend standard safety glasses or a
wide vision safety mask worn over spectacles.

model no. 060-1963-8 | contact us 1.866.523.5218 model no. 060-1963-8 | contact us 1.866.523.5218
5
Important Safety Instructions
WARNING: Read all safety warnings and instructions. Failure to
follow the warnings and instructions may result in electric shock,
re and/or serious injury.
FOR ALL APPLIANCES
• Avoid dangerous environments — do not
use appliances in damp or wet locations.
• Don’t use in rain.
• Keep children away — all people and
pets should be kept at a distance from
the work area.
• Dress properly — do not wear loose
clothing or jewellery. They can be
caught in moving parts. Wear protective
clothing; use of work gloves, long
pants, a long-sleeved shirt and safety
footwear is recommended when working
outdoors. Wear protective hair covering
to contain long hair.
• Use safety glasses — always use face
or dust mask if the area in which you are
working is dusty.
• Use the right appliance — do not use
appliance for any job except that for
which it is intended.
• Do not force appliance — it will do the
job better and with less likelihood of a
risk of injury at the rate for which it was
designed.
• Do not overreach — keep proper footing
and balance at all times.
• Stay alert. Use common sense. Do not
operate appliance when you are tired or
under the inuence of drugs, alcohol or
medication.
• When not in use, appliances should be
stored indoors in dry places out of reach
of children.
• Maintain appliance with care. Follow
instructions for lubricating and changing
accessories. Keep handles dry, clean,
and free from oil and grease.
• Check damaged parts. Before using the
appliance, make sure the safety guards
are intact. Never use a tool without its
safety guard. Check the alignment of the
moving parts, the binding of the moving
parts. Check for broken or defective
parts that can affect the safe operation
of your tool. A guard or other part that is
damaged should be properly repaired
or replaced by an authorized service
centre unless indicated elsewhere in this
manual.
FOR ALL BATTERY-OPERATED
GARDENING APPLIANCES:
1. Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to battery pack, picking up
or carrying the appliance. Carrying the
appliance with your nger on the switch
or energizing an appliance that has the
switch on invites accidents.
2. Disconnect the battery pack from
the appliance before making any
adjustments, changing accessories,
or storing appliance. Such preventive
safety measures reduce the risk of
starting the appliance accidentally.
3. Recharge only with the charger specied
by the manufacturer. A charger that is
suitable for one type of battery pack
may create a risk of re when used with
another battery pack.
4. Use appliances only with specically
designated battery packs. Use of any
other battery packs may create a risk of
injury and re.
5. When battery pack is not in use, keep
it away from other metal objects, like
paper clips, coins, keys, nails, screws
or other small metal objects, that can
make a connection from one terminal to
another. Shorting the battery terminals
together may cause burns or a re.
6. Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
Safety Instructions

model no. 060-1963-8 | contact us 1.866.523.5218
6
Safety Instructions
If contact accidentally occurs, ush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from
the battery may cause irritation or burns.
7. Do not use a battery pack or appliance
that is damaged or modied. Damaged
or modied batteries may exhibit
unpredictable behaviour resulting in re,
explosion or risk of injury.
8. Do not expose a battery pack
or appliance to re or excessive
temperature. Exposure to re or
temperature above 130°C (265°F) may
cause an explosion.
9. Follow all charging instructions and do
not charge the battery pack or appliance
outside of the temperature range
specied in the instructions. Charging
improperly or at temperatures outside
of the specied range may damage the
battery and increase the risk of re.
10. Have servicing performed by a qualied
repair person using only identical
replacement parts. This will ensure that
the safety of the product is maintained.
11. Do not modify or attempt to repair
the appliance or the battery pack (as
applicable) except as indicated in the
instructions for use and care.
FOR LAWN TRIMMER AND EDGE
TRIMMER
1. Keep guards in place and in good
working order.
2. Keep hands and feet away from cutting
area.
3. Do not use heavier lines than
recommended in this manual.
4. Do not use line materials of other types
– for example, metal wire, rope, and the
like.
FOR BATTERY PACK
1.
Do not dismantle, open or shred cells or
battery pack.
2.
Do not expose battery pack to heat or re.
Avoid storage in direct sunlight.
3.
Do not short-circuit a battery pack. Do
not store battery packs haphazardly in
a box or drawer where they may short-
circuit each other or be short-circuited by
conductive materials. When battery pack
is not in use, keep it away from other metal
objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that
can make a connection from one terminal
to another. Shorting the battery terminals
together may cause burns or a re.
4.
Do not subject battery pack to mechanical
shock.
5.
In the event of battery leaking, do not allow
the liquid to come into contact with the skin
or eyes. If contact has been made, wash
the affected area with copious amounts of
water and seek medical advice.
6.
Do not use any battery pack which is not
designed for use with the equipment.
7.
Keep battery pack out of the reach of
children.
8.
Always purchase the battery pack
recommended by the device manufacturer
for the equipment.
9.
Keep battery pack clean and dry.
10.
Wipe the battery pack terminals with a
clean, dry cloth if they become dirty.
11.
Battery pack needs to be charged before
use. Always use the correct charger and
refer to the manufacturer’s instructions
or equipment manual for proper charging
instructions.
12.
Do not leave battery pack on prolonged
charge when not in use.
13.
After extended periods of storage, it may
be necessary to charge and discharge
the battery pack several times to obtain
maximum performance.
14.
Recharge only with the charger specied
by
Yardworks
®
. Do not use any charger
other than that specically provided for
use with the equipment.
15.
Retain the original product literature for
future reference.

model no. 060-1963-8 | contact us 1.866.523.5218 model no. 060-1963-8 | contact us 1.866.523.5218
7
16.
Use only the battery pack in the
application for which it was intended.
17.
Remove the battery from the equipment
when not in use.
18.
Dispose of properly.
19.
Do not mix cells of different manufacture,
capacity, size or type within a device.
20.
Keep the battery away from microwaves
and high pressure.
Information for radiated emission
This device complies with Canadian ICES-
001.
This device complies with Part 15 of the FCC
Rules.
Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference; and
(2) This device must accept any interference
received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
Safety Instructions
WARNING: Changes or modications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority
to operate the equipment.

model no. 060-1963-8 | contact us 1.866.523.5218
8
Symbols
SAVE THESE INSTRUCTIONS!
Symbol Designation/Explanation
To reduce the risk of injury, user must read instruction manual.
Warning
Wear eye protection
Wear ear protection
This part directs thrown objects away from the operator
Li-ion battery; battery must be recycled.
Do not burn.
Batteries may enter water cycle if disposed improperly, which can be
hazardous for ecosystem. Do not dispose of waste batteries as unsorted
municipal waste.
Yardworks
®
Inc. has established a partnership with the RBRC Corporation
to recycle any
Yardworks
®
batteries with the RBRC-call2recycle seal. For
environmental protection, please do not discard batteries in the trash.
After the battery’s life cycle is ended, please call 1-800-822-8837 for a free
service that will properly dispose of the battery.
Some of the following symbols may be used on this product. Please study them and learn
their meaning. Proper interpretation of these symbols will allow you to operate the product
effectively and safely.

model no. 060-1963-8 | contact us 1.866.523.5218 model no. 060-1963-8 | contact us 1.866.523.5218
9
Product Specications
TECHNICAL DATA
Voltage 48V
No Load Speed 0-6000 RPM
Cutting Diameter 36 cm (14”)
Line Diameter 2.0 mm (0.080")
Line Length 4 m (160”)
Battery Capacity (060-1987-2) 2.0 Ah
Charger Input (060-1990-2) 120 V~, 60 Hz, 110 W
Charger Output (060-1990-2) 48 V
, 2 A
Charging Time 1 hr
Machine Weight 11 lb 7 oz (5.2 kg)
SUITABLE BATTERY PACKS
Item
Number
060-1987-2 ABP4830SH1 060-1988-0 ABP4850SH 060-1989-8
Battery
Capacity
2.0 Ah 3.0 Ah 4.0 Ah 5.0 Ah 6.0 Ah
Included
Not
included
Not
included
Not
included
Not
recommended
SUITABLE CHARGERS
Item Number 060-1990-2 060-1992-8 060-1909-0
Charger Input
120 V~, 60 Hz,
110 W
120 V~, 60 Hz,
320 W
120 V~, 60 Hz,
250 W
Charger
Output
48 V
, 2 A 48 V , 6 A
48 V , 2 A (output 1)
48 V , 2 A (output 2)
Charger
Protection
Class
/II /II /II
Included Not included Not included

model no. 060-1963-8 | contact us 1.866.523.5218
10
1.
Battery pack (060-1987-2)
2. Battery pack release
button
3. Hex key
4. On/Off switch with
variable speed control
5. Lock-off button
6. Auxiliary handle
7. Handle locking nut
8. Handle locking clamp
9. Handle locking knob
10. Upper shaft
11. Couplings
12. Lower shaft
13. Safety guard
14. Trimmer head
15. Spool holder
16. Line cutter
17. Spool holder release
knob x 2
18. Bump knob
19. Line tting knob
20. Line
21. Line tting hole x 2
22. Charger (060-1990-2)
23. Bolt x 3 (Fig. A2 & C1)
WARNING: Any other accessory or attachment may increase the risk of
injury.
Product Diagram
10
11
22
1
2
5
4
3
Tool storage
6
7
8
9
12
13
14
15
16
17
18
192021

model no. 060-1963-8 | contact us 1.866.523.5218 model no. 060-1963-8 | contact us 1.866.523.5218
11
1. ASSEMBLING THE UPPER SHAFT AND LOWER SHAFT
Connect the couplings into each other (see Fig. A1). Align the holes and fasten the couplings
by screwing the bolt with the hex key (see Fig. A2).
To reduce the risk of injury, user must read instruction manual.
Intended Use
The machine is intended for the cutting of grass and weeds under bushes as well as on
slopes and edges that cannot be reached with a lawn mower.
CAUTION! The trimmer must not be operated before it has been
assembled completely.
CAUTION! Do not insert the battery until the trimmer has been
completely assembled.
23
A2
A1
2. ASSEMBLING THE AUXILIARY HANDLE
Attach the
auxiliary handle
and locking clamp on the upper shaft
(see Fig. B1)
. Put the
locking nut through the holes and tighten the
auxiliary
handle with the locking knob
(see
Fig. B2)
.
Assembly
B2
B1
2
1
1
2

model no. 060-1963-8 | contact us 1.866.523.5218model no. 060-1963-8 | contact us 1.866.523.5218
12
3. ASSEMBLING THE SAFETY GUARD
Attach the safety guard to the lower shaft as shown in Fig. C1. Align the 2 holes on the safety
guard with the 2 corresponding holes on the lower shaft.
Hold the safety guard in place and insert the 2 bolts into the 2 aligned holes.
Secure the safety guard onto the lower shaft with the provided hex key (see Fig. C2).
Assembly
WARNING: Never operate the tool without the guard properly in
place. Use of the unit without having installed the guard may
result in injury.
WARNING: The guard has a very sharp line cutter.
C2
C1
1
2
3

model no. 060-1963-8 | contact us 1.866.523.5218 model no. 060-1963-8 | contact us 1.866.523.5218
13
model no. 060-1963-8 | contact us 1.866.523.5218
BEFORE USING YOUR LINE TRIMMER
1. CHARGING THE BATTERY (SEE FIG. D)
a. The battery in your new tool is not charged when it leaves the plant; therefore, it must
be fully charged before using the rst time.
b. If the battery pack is very hot, remove the battery from the charger and allow it to cool
to ambient temperature before attempting to recharge.
c. To prevent damage to the battery pack, please charge the battery to full or no less
than half charge before storage.
d. If the tool will not be used for long periods of time, charge the battery pack every 3 – 6
months.
- CHARGING PROCEDURE
1) Plug the charger into an appropriate outlet.
2) Slide the battery pack into the charger; make sure the battery is in the correct charge
position rmly. The charger light will begin ashing green to indicate the charging
process has started.
3) When charging is completed, the light will turn solid green.
4) When the battery is fully charged, unplug the charger and remove the battery pack.
NOTE: If the battery pack is locked in the charger, press the battery pack release button
and remove it.
WARNING: When battery charge runs out after continuous use or
exposure to direct sunlight or heat, allow time for the battery to
cool down before re-charging to achieve the full charge.
WARNING! The charger and battery pack are specially designed to
work together, so do not attempt to use any other devices. Never
insert or allow metallic objects into your charger or battery pack
connections because an electrical failure and hazard will occur.
D
Operation

model no. 060-1963-8 | contact us 1.866.523.5218
14
- CHARGING INDICATOR
This charger is designed to detect some problems that can arise with battery packs.
Indicator lights indicate problems (see table below).
Light ON/ Flash Status
Red on
Defective battery.
Red ash
Battery Temperature Protection.
The temperature of battery pack is
less than 0°C (32°F) or more than
40°C (104°F).
Green on
Fully charged.
Green ash Charging.
2. INSTALLING AND REMOVING THE BATTERY PACK
Slide the battery pack into tool’s battery port. A simple push and slight pressure will be
sufcient (
s
ee Fig. E1).
Press the battery pack latch and remove the battery pack from the tool (
s
ee Fig. E2).
Operation
E2
E1
1
2

model no. 060-1963-8 | contact us 1.866.523.5218 model no. 060-1963-8 | contact us 1.866.523.5218
15
OPERATION
1. ON/OFF SWITCH WITH VARIABLE SPEED CONTROL
To switch on, press the lock-off button rst, then the On/Off switch (
s
ee Fig. F). To switch
off, release the On/Off switch.
The On/Off switch is also a variable speed switch that delivers higher speed with increased
trigger pressure. Speed is controlled by the amount of switch trigger depression.
2. TRIMMING
1) Keep the trimmer head at an angle of about 30° to the ground when trimming (
s
ee Fig.
G1).
2) Do not cut wet grass because the grass tends to stick to the trimmer head and guard,
prevents proper discharge of grass clippings, and could cause you to slip and fall.
3) Regularly remove clippings and dirt around the trimmer head. Ensure the trimmer is
switched off.
4) Work rhythmically, and stand rmly with your feet apart. Cut from right to left so the
trimmings will be thrown away from the work area (
s
ee Fig. G2).
5) When cutting long or high grass, please make sure that you cut the grass down in 2 to
3 stages (
s
ee Fig. G3, G4).
6) Do not move the trimmer too fast as this will result in ineffective cutting and possible
damage.
WARNING: Always wear eye protection. Never lean over the trimmer
head. Rocks or debris can ricochet or be thrown into eyes and face
and cause blindness or other serious injury.
WARNING: Make sure that line is fed out before operation. Make sure
motor is up to full speed before trimming.
WARNING: Do not remove or alter the line-cutting blade assembly.
Excessive line length will be cut to suitable length.
Operation
E2
F
1
2

model no. 060-1963-8 | contact us 1.866.523.5218
16
3. ADJUSTING CUTTING LINE LENGTH
The trimmer head allows the operator to release more cutting line without stopping the
motor. As line becomes frayed or worn, additional line can be released by lightly tapping the
bump knob on the ground while operating the trimmer (
s
ee Fig. H).
NOTE: Line release will become more difcult if the line cutter becomes dull.
Operation
G2
G1
30
0
G4
G3
G2
H

model no. 060-1963-8 | contact us 1.866.523.5218 model no. 060-1963-8 | contact us 1.866.523.5218
17
3. REPLACING THE LINE
With the automatic line tting system, you only need to replace the line instead of replacing
the whole spool holder, and you do not need to wind the line manually.
1) Remove the battery pack from the grass trimmer rst.
2) Cut a piece of line approximately 4 m (160”).
3) Turn over the grass trimmer. Insert one end of the line continuously into a line tting
hole at the edge side of the spool holder, and the line will go through the inner spool
holder itself and stretch out from the other line tting hole (
s
ee Fig. I1).
4) Pull out the other end of the line until half of the line is streched out from the other
hole. Note that the length of the two parts line should be the same (
s
ee Fig. I2).
5) Hold the spool holder by hand and grip the line tting knob with another hand, rotate
the line tting knob clockwise (the same direction shown on the bump knob). The line
will wind onto the spool automatically (
s
ee Fig. I3).
6) Continue to rotate the line tting knob until the line is at the desired length (
s
ee Fig. I4).
NOTE: Do not over-rotate the line tting knob, or the extended line will be too short.
WARNING: Your trimmer is designed to use only line with a maximum
diameter of 2.0 mm (0.080”).
WARNING: Always remove the battery pack from your trimmer after use.
Operation
I2
I1
I3
I4

model no. 060-1963-8 | contact us 1.866.523.5218
18
MAINTENANCE
Always check the product prior to use for any damage.
After use, disconnect the battery from the tool and check for damage.
Your power tool requires no additional lubrication or maintenance. There are no user
serviceable parts in your power tool. Never use water or chemical cleaners to clean your
power tool. Wipe clean with a dry cloth. Always store your trimmer in a dry room. Keep
the motor ventilation slots clean. Keep all working controls free of dust.
STORAGE
Store in a dry place where the trimmer and battery can be protected from damage.
For battery tools
The ambient temperature range for the use and storage of tool and battery is 0 to 45°C
(32 to 113°F).
The recommended ambient temperature range for the charging system during charging is
0 to 40°C (32 to 104°F).
It is recommended that the battery be stored indoors for the winter months.
Maintenance and Storage

model no. 060-1963-8 | contact us 1.866.523.5218 model no. 060-1963-8 | contact us 1.866.523.5218
19
Troubleshooting
TROUBLESHOOTING
The following table gives problems and actions that you can perform if your machine does
not operate correctly. Warning: Switch the trimmer off and remove the battery prior to any
troubleshooting.
Problem Possible Cause Corrective Action
Trimmer fails to operate.
Battery discharged.
Battery too hot/cold.
Motor is broken.
Internal wiring of machine
damaged.
Recharge battery; also see the content
in charger manual.
Allow to cool/warm.
Contact Yardworks
®
at 1.866.523.5218.
Contact Yardworks
®
at 1.866.523.5218.
Trimmer runs
intermittently.
Motor is broken.
Battery not fully charged.
On/Off switch defective.
Contact Service Agent.
Recharge battery.
Contact Yardworks
®
at 1.866.523.5218.
Excessive vibrations
/noise.
Machine defective.
Line spool is not wound well.
Contact Yardworks
®
at 1.866.523.5218.
Rewind the line. See “Replacing the
line’’.
Cutting time per battery
charge too short.
Battery has not been used for
long period or only charged for
short term.
Grass too high.
Battery defective.
Fully charge battery; also see the
content in charger manual.
Cut in stages.
Replace the battery.
Machine does not cut.
Line broken.
Battery not fully charged.
Motor is broken (speed is too
low).
Grass entangled around cutting
head.
Replace the line.
Recharge battery; also see the content
in charger manual.
Contact Yardworks
®
at 1.866.523.5218.
Remove grass.
Continuous lighting of the
battery charge indicator/
battery not charging.
Battery not (properly) inserted.
Battery contacts contaminated.
Battery defective.
Properly insert battery into battery
charger.
Clean the battery contacts or replace
the battery.
Replace the battery.
Battery charge indicator
does not light up.
Plug of battery charger not
plugged in (properly).
Outlet or mains cable defective.
Battery charger defective.
Insert mains plug (fully) into the socket
outlet.
Check the mains voltage.
Replace the battery charger.

model no. 060-1963-8 | contact us 1.866.523.5218
20
11
1
2(3)
3
4
5
6
7
9
10(3)
11
12
13
14(2)
15
16
11
17
18
19
20(3)
21(3)
101
22
23
24
25
26(2)
27(2)
28
29(2)
30
31
32
33
34(2)
35
36
37
38
39
40
41
42
43
46(2)
42
26(7)
62
61
45
49
47
48
50
51
52
53
26(2)
55
56
57(8)
52
51
26(9)
60
54
Exploded View

model no. 060-1963-8 | contact us 1.866.523.5218 model no. 060-1963-8 | contact us 1.866.523.5218
21
Parts List
No. Part Description Quantity
1 Cover 1
2 Self Tapping Screw 3
3 Ball Bearing 6000 1
4 Cutting Head Cover 1
5 Washer 1
6 Self Tapping Screw 1
7 Separate Plate 1
9 Spool & Line 1
10 Self Tapping Screw 3
11 Inner Cover 1
12 Compression Spring 1
13 Outprut Shaft 1
14 Rivet 2
15 Chuck Body 1
16 Fan 1
17 Motor Mounting Plate 1
18 Motor 1
19 Housing 1
20 Screw 3
21 Rubber Sleeve 3
22 Screw Washer Assembly 1
23 Lower Aluminium Tube 1
24 Guard Set 1
25 Blade 1
26 Self Tapping Screw 20
27 Screw 2
28 Connector II 1
29 Screw Washer Assembly 2
30 Screw 1
31 Nut 1
32 Connector I 1
33 Screw 1
34 Screw 2
35 Upper Aluminium Tube 1
36 Connection Wire 1
37 Angle Knob 1
38 Press Plate 1
39 Auxiliary Handle 1
40 Bolt 1
41 Handle Cover 1
42 Left/Right Handle 1
43 Switch 1
45 Trigger 1
46 Self Tapping Screw 2
47 Compression Spring 1
48 Lock Knob 1
49 Tube 1
50 Decorative Cover 1
51 Left/Right Side Cover 1
52 Left/Right Battery Support 1
53 Cord Clamp 1
54 Terminal 1
55 Torsional Spring 1
56 Protect Control Board 1
57 Self Tapping Screw 8
60 Spanner 1
61 Battery Pack (
060-1987-2)
1
62 Charger
(060-1990-2)
1
101 Cutting Head Assembly 1

model no. 060-1963-8 | contact us 1.866.523.5218model no. 060-1963-8 | contact us 1.866.523.5218
22
Always remove or disconnect the battery pack before adjusting,
cleaning, servicing or transporting your appliance.
FIVE-YEAR LIMITED WARRANTY
For ve (5) years from the date of purchase
within Canada, Yardworks Canada will, at
its option, repair or replace for the original
purchaser, free of charge, any part or
parts found to be defective in material or
workmanship (excludes battery and charger).
For three (3) years from the date of purchase
within Canada, Yardworks Canada will, at
its option, repair or replace for the original
purchaser, free of charge, any battery or
charger found to be defective in material or
workmanship.
THIS WARRANTY DOES NOT COVER
1. Any part that has become inoperative
due to misuse, commercial use, abuse,
neglect, accident, improper maintenance,
or alteration;
2. The unit, if it has not been operated and/
or maintained in accordance with the
owner’s manual;
3. Normal wear, except as noted below;
4. Routine maintenance items such as
lubricants, blade sharpening; or
5. Normal deterioration of the exterior nish
due to use or exposure.
FULL ONE YEAR (365) DAYS WARRANTY
ON NORMAL WEAR PARTS
Normal wear parts are dened as blade
adaptors, blades, grass bags and tires.
These parts are warranted to the original
purchaser to be free from defects in
material and workmanship for a period of
three hundred and sixty-ve (365) days from
the date of retail purchase.
HOW TO OBTAIN SERVICE
Warranty service is available by calling
the toll-free helpline at 1.866.523.5218.
The factory will not accept the return of a
complete unit unless prior written permission
has been extended by Yardworks Canada.
TRANSPORTATION CHARGES
Transportation charges for the movement
of any power equipment unit or attachment
are the responsibility of the purchaser.
The purchaser must pay transportation
charges for any part submitted for
replacement under this warranty unless
such return is requested in writing by
Yardworks Canada.
OTHER WARRANTIES
All other warranties, express or implied,
including any implied warranty of
merchantability is limited in its duration to
that set forth in this express limited warranty.
The provisions as set forth in this warranty
provide the sole and exclusive remedy of
Yardworks Canada obligations arising
from the sale of its products.
Warranty

model no. 060-1963-8 | contact us 1.866.523.5218 model no. 060-1963-8 | contact us 1.866.523.5218
23
model no. 060-1963-8 | contact us 1.866.523.5218
FCC Part 15
Supplier’s Declaration of Conformity
Product Description: 48V 2.0A Charger
Model Number: 060-1990-2
Trade Name: YARDWORKS
®
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Responsible Party:

