4.5 cu.ft. FRONT-LOADING WASHER
H
C
QUICK INSTALLATION GUIDE QUICK INSTALLATION GUIDE CONT.
This quick reference guide is provided for informational purposes only and does not replace,
modify or change in any manner the User Manual & Installation Instructions.
UNPACK YOUR WASHER
REMOVE SHIPPING HARDWARE
1
2
CONNECT HOSES TO
WATER SUPPLY
INSTALL DRAIN HOSE AND
CONNECT TO POWER SUPPLY
TEST CYCLE
4
6
8
IMPORTANT: Save all bolts and spacers for future use.
3
5
7
CONNECT HOSES TO WASHER
LEVEL YOUR WASHER
INSTALLATION CHECKLIST
1. Once the washer is within 4 feet of its fi nal
location, use an adjustable or 1⁄2 ” socket wrench
to remove the following from the back of the
washer:
• 4 shipping bolts
• 4 plastic spacers (including rubber grommets)
• 4 power cord retainers
2. Insert the hole caps into the bolt holes after the
shipping bolts and spacers have been removed.
1. Run water from both
faucets to fl ush the
lines and remove
particles that might
clog the water valve
screens.
2. Ensure that a rubber
washer is in the end
of the hot and cold
hoses.
3. Connect the inlet hoses
to the hot “H” outlet and
cold “C” outlet.
4. Hand-tighten, and then tighten the
connections another
2⁄3 turn using pliers.
1. Rock the washer into fi nal
location, ensuring inlet
hoses do not become
kinked.
2. Place level on top of
washer.
3. Adjust the front leveling
legs up or down using a
9⁄16” wrench.
4. Level washer both side-
to-side and front-to-back.
5. Turn lock nuts on leveling
legs up toward the base
of the washer, and then
tighten with the 9⁄16”
wrench.
Main power is turned on.
The washer is plugged in.
Water hoses are connected securely.
Faucets are turned on.
Washer is level and all legs are on the fl oor.
Shipping bolts and spacers are removed.
Drain hose is placed in tub or standpipe and secured
with a cable tie.
1. Ensure that a screen
washer is inserted
into the faucet end
of both hoses. If a
rubber washer is
already inserted,
remove before
inserting screen
washer.
2. Connect the inlet
hose from the “H”
outlet to the hot faucet
and the inlet hose from
the “C” outlet to the cold
faucet.
3. Hand-tighten, and then tighten the connections
another
2⁄3 turn using pliers.
4. Turn on the water and check for leaks.
1. Attach U-shaped hose guide
to end of drain hose.
2. Place drain hose
in laundry tub or
standpipe and
secure with
cable tie.
NOTE: If placed in
a standpipe, the
end of the drain
hose should extend
only 4 to 7 inches
down the pipe.
3. Plug washer into a
grounded outlet. Do
not use an extension cord
or adapter plug.
1. Wash a load of clothes in the SPEED WASH cycle.
2. Check for leaks.
3. When the load is spinning at high speed, make sure the
washer and leveling legs are stable.
4. If necessary, adjust the front leveling legs while the
washer is in the spin cycle until the washer is level.
WARNING
For your safety
•
To reduce the risk of fi re, electric shock, or injury to persons when using or installing the product, read and obey all safety
information provided in the User Manual & Installation Instructions that accompanied the product.
•
Do not install or store your appliance in an area where it will be exposed to dripping water or outside weather conditions. See
Location of Your Washer section in the User Manual & Installation Instructions.
•
NOTE: This appliance must be properly grounded and installed as described in these steps and the User Manual & Installation
Instructions. Electrical service to the washer must conform with local codes and ordinances and the latest edition of the
national Electrical Code, ANSI/NFPA 70.
Parts supplied
Cable Tie
Adjustable wrench
or
1⁄2” socket with ratchet
Adjustable wrench or
9⁄16” open-end wrench
Carpenter’s level
Channel-lock
adjustable pliers
Screen Washers (2)
Hose Guide
Tools needed
Thank you for purchasing the Element 4.5 cu.ft. Front Load Washer. If you have questions about
your washer,our customer support team is ready to help:
4.5 cu.ft. FRONT-LOADING WASHER-USER MANUAL
4.5 cu.ft. Washer
WASHER SAFETY ..............................................................................3
When Not in Use .......................................................................................5
OPERATION REQUIREMENTS ..........................................................6
INSTALLATION INSTRUCTIONS ......................................................8
Parts Supplied.............................................................................................9
Rough-In Dimensions ..............................................................................9
11
WASHER USE ....................................................................................13
WASHER CARE ................................................................................24
28
BEFORE YOU CALL FOR SERVICE... ............................................29
36
3
Washer
Safety
Installation
Instructions
Washer Use
YOUR SAFETY AND THE SAFETY OF OTHERS ARE VERY
IMPORTANT
CAUTION
WARNINGWARNING
WARNING
This symbol indicates the possibility of injury or damage
property.
This
injury.
4
Washer
Safety
Installation
Instructions
Washer Use
WARNING
•
•
•
•
•
supervision of children is necessary when this appliance is used near
DO NOT reach into the appliance if the drum or other components
•
•
DO NOT tamper with controls, repair or replace any part of this
•
in the user maintenance instructions or in published user repair
•
possibility of slipping.
•
partially disassembled, or has missing or broken parts including a
damaged cord or plug.
•
Pressing the Power button DOES NOT disconnect power.
•
by persons (including children) with reduced physical, sensory or
DO NOT wash or dry clothes that have been previously washed,
cleaned, soaked, or spotted with gasoline, dry-cleaning solvents,
5
Washer
Safety
Installation
Instructions
Washer Use
If the supply cord is damaged, it must be replaced by the
•
The new hose-sets bought from the retailer where the product was
•
reused.
•
PROPER INSTALLATION
•
•
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
•
•
Do not use an adapter.
•
•
•
shock.
WHEN NOT IN USE
SAVE THESE INSTUCTIONS
•
Install or store the washer where it will not be exposed to
temperatures below freezing or exposed to the weather, which could
cause permanent damage.
6
Washer
Safety
Installation
Instructions
Washer Use
OPERATION REQUIREMENTS
LOCATION OF YOUR WASHER
1.
℃
2. In an area where it will come in contact with curtains or drapes.
3. On carpet. The floor MUST be a hard surface with a maximum slope
of
1/2"
NOTE: If floor is in poor condition, usea
3/4
IMPORTANT: MINIMUM INSTALLATION CLEARANCES
Back = 3" (7.6 cm)
ELECTRICAL REQUIREMENTS
WARNING
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG
•
accordance with local codes and ordinances.
CIRCUIT - Individual, properly polarized and grounded 16-amp branch
circuit fused with 16-amp time -delay fuse or circuit breaker.
power supply cord is accessible when the washer is in an installed
position.
POWER SUPPLY - 2-wire with ground, 120V~, single-phase, 60Hz,
7
Washer
Safety
Installation
Instructions
Washer Use
GROUNDING REQUIREMENTS
Improper connection of the equipment grounding conductor can result
doubt as to whether the appliance is properly grounded.
1.
breakdown, grounding will reduce the risk of electrical shock by
2.
equipment-grounding conductor and a grounding plug, the plug
is properly installed and grounded in accordance with all local codes.
licensed electrician replace it with a properly grounded grounding-type
WATER SUPPLY REQUIREMENTS
DRAIN REQUIREMENTS
1.
2. A standpipe diameter of 1
1/4
" (3.18 cm) minimum.
3.
BACK
47.24''
(120 cm)
Max.
24''
(61 cm)
Min.
3/4
" (1.9 cm) garden hose-type so
8
Washer
Safety
Installation
Instructions
Washer Use
BEFORE YOU BEGIN
FOR YOUR SAFETY:
WARNING
• This appliance must be properly grounded and installed as described
• N OTE: This appliance must be properly grounded, and electrical
service to the washer.
TOOLS REQUIRED
• Adjustable wrench or 1/2" socket with ratchet
• Adjustable wrench or
9/16
" open-end wrench
• Channel-lock adjustable pliers
Certain internal parts are intentionally not grounded and may
•
present a risk of electric shock only during servicing. Service
IMPORTANT -
•
IMPORTANT -
•
ordinances.
• Note to Installer -
Consumer.
• Note to Consumer -
•
and electrical skills.
•
•
9
Washer
Safety
Installation
Instructions
Washer Use
PARTS REQUIRED (OBTAIN LOCALLY)
PARTS SUPPLIED
Cable Tie Drain Hose Guide
ROUGH-IN DIMENSIONS
27.0''
(68.6 cm)
39.8''
(101.09 cm)
SIDE
34.2''
(86.9cm)
39.8''
(101.09 cm)
∗NOTE:
Stacked, 84"
10
Washer
Safety
Installation
Instructions
Washer Use
UNPACKING THE WASHER
WARNING:
•
1.
2.
lay the washer on its front or back.
(inserted in the
center of the base).
3.
4.
carton.
5.
6.
4 bolts
4 plastic spacers (including rubber grommets)
4 power cord retainers
Recycle or destroy the carton and plastic bags after the washer is
unpacked. Make sure children are not able to get a hold of materials.
Children might play with them. Cartons covered with rugs, bedding
or plastic sheets can become airtight chambers causing suffocation.
11
Washer
Safety
Installation
Instructions
Washer Use
hardware in the plastic bag provided.
INSTALLING THE WASHER
1.
2.
3. Install the screen washers by inserting them into the free ends of the
inlet hoses with the protruded side facing the faucet.
4.
tightly by hand, then tighten another
2/3
5.
into position ensuring the inlet hoses do not become kinked. It is important
washer into its final position.
NOTE: To reduce vibration, ensure that all four rubber leveling legs are
firmly touching the floor. Push and pull on the back right and then back
left of your washer.
washer into the hose fitting if it has fallen out during shipment.
valve. Tighten by hand; then
Carefully connect the inlet hose marked HOT to the rear “H” inlet
12
Washer
Safety
Installation
Instructions
Washer Use
NOTE: Do not use the dispenser drawer or door to lift the washer.
6.
(if the washer is installed under a counter, the washer should not be
washer
nuts on each leg up towards the
base of the washer and snug with a wrench.
7.
the hose in a laundry tub or standpipe and secure it with the cable tie
Cable
Tie
Cable
Tie
Cable
NOTE: Placing the drain hose too far down the drain pipe can cause a
fit can also cause a siphoning action.
8. Plug the power cord into a grounded outlet.
9.
10.
11. Before starting the washer, check to make sure:
Main power is turned on.
•
The washer is plugged in.
•
13
Washer
Safety
Installation
Instructions
Washer Use
12.
13.
14.
CONTROL PANEL
•
•
•
•
-
14
Washer
Safety
Installation
Instructions
Washer Use
QUICK START
Press the Power button.
If the screen is dark, a press of the Power
Power
Press to put
NOTE: Pressing Power does not disconnect the appliance from the
W ash Cycles
Normal/
Colors*
For heavily to lightly soiled colorfast cottons, household
linens, work and play clothes.
Sheets* and similar bulky items.
Heavy
Duty* or towels.
clothes
Towels* For items such as towels, sheets, pillowcases and dish
rags.
Sanitize*
options.
Baby Care
the baby skin.
laundry may become damaged See the Care and Cleaning
section.
Rinse &
Spin
15
Washer
Safety
Installation
Instructions
Washer Use
SOIL LEVEL
increase or decrease the
can choose between
Extra Light, Light,
Medium, Heavy or Extra
WASH TEMP
Adjust to select the proper
always cold to help reduce
energy usage and reduce
setting of stains and
wrinkles.
Follow the fabric
manufacturer’s care label
when selecting the wash
To change the wash
wash Temp button until
desired setting.
Tap Cold, Cold, Warm, Hot
Extra Hot.
By design, to protect
fabrics, not all wash
SPIN SPEED
Changing the Spin speed
changes the final spin
manufacturer’s care label
when changing the Spin
speed.
To change the Spin
speed, press the Spin
Medium, High or Extra
High. Higher spin speeds
Higher spin speeds
the clothes and will help
also increase the possibility
of setting wrinkles on some
fabrics.
16
Washer
Safety
Installation
Instructions
Washer Use
STEAM
Steam adds steam into
the washer to assist with
loosening stains on the
To use:
1.
2. Select the Add Steam
steam.
3. Press the
button.
WATER
PLUS
of the main wash.
Heavy Duty, Whites,
To use:
1.
2. Select the Add Water
3.
SPEED
WASH
This option reduces the
by optimizing the wash,
rinse and spin actions and/
or gently raising the wash
cleaned faster. Option
Towels, Baby Care or
and options selected.
To use:
1.
an option.
2. Make any adjustments
to Soil, Temp and Spin
as desired.
3.
button to reduce the
4.
EXTRA
RINSE
detergent from soiled
loads.
17
Washer
Safety
Installation
Instructions
Washer Use
Press the
button.
Press the
button.
.
SIGNAL
Use the Signal pad to
turn the Signal on or off
all knob turns and button
presses.
means it is an acceptable
Turn Signal on, signal beeps
options, and a double beeps
means not an acceptable
option.
Towels, Sanitize, Delicates,
Baby Care, Sportswear
PRE SOAK
garments prior to the
begins with a brief tumble
wash cycle. This option
and then proceeds to
soak the clothes with
an additional 10-20 minutes
from the main wash
compartment in the
EXTRA
RINSE and
PRE SOAK
can lock or unlock the
Children cannot
accidentally start the
washer by touching
buttons with this option
selected.
To lock the washer, press
and hold the Extra Rinse
3 seconds.
To unlock the washer
controls, press and hold
NOTE: The Power button
can still be used when the
machine is locked.
MY CYCLE
set the desired setting
spin speed and wash temp
settings and hold down
3 seconds, A beep will
set the desired setting and
has been started.
prior to pressing
18
Washer
Safety
Installation
Instructions
Washer Use
button.
DELAY
Wash button to choose
want to delay the start of
desired time is reached,
press the
button. The
machine will count down
when the delay is counting
down, the machine will
enter a paused state.
and press
again in order to restart
the countdown.
Display
time remaining until the
the balance of the load
see the time remaining
on the display increase to
spin speed to handle
unbalanced loads.
B
A
C
D
selected.
Press to start a wash
running, pressing it once
will pause the washer.
Press again to restart the
garment, press the
The washer will unlock the
door. Press again to restart
washer will drain first, then
unlock the door when it is
paused.
NOTE: The washer
checks after pressing the
flows, this is normal.
Wash Time Delay Time
End
Error
A
Display
B
Remain-Delay
C
Child Lock
D
Door Lock
19
Washer
Safety
Installation
Instructions
Washer Use
button
button.
button.
Pre
-
the door, a double beep will
sound when pressing
pause/add garment button.
FEATURES
THE DISPENSER DRAWER
Slowly open the dispenser drawer by pulling it out until it stops.
After adding laundry products, slowly close the dispenser drawer. Closing
the drawer too quickly could result in early dispensing of the bleach,
fabric softener or detergent.
is a result of the flushing/siphoning action and is part of the normal
20
Washer
Safety
Installation
Instructions
Washer Use
NOTE: Liquid detergent will drain into the washer drum as it is added.
•
residue being left on the clothes.
The Detergent Compartment
High-efficient detergent is required for this washer.
•
Use the detergent manufacturer’s recommended amount.
Add measured detergent to the front left detergent compartment of
Detergent is flushed from the dispenser at the beginning of the wash
•
the dispenser drawer.
•
•
manufacturer’s instructions when measuring the amount of powder to
•
residue being left on the clothes.
residue buildup in your washer.
Using more detergent than the recommended quantity can cause
•
•
DETERGENT
SO
LIQUID
3X
2X
1X
remove for powder
Normal
HE Liquid
Detergent
Setting
2X HE Liquid
Detergent Setting
(most common
setting)
3X HE
Liquid
Detergent
Setting
Remove for powder detergent
21
Washer
Safety
Installation
Instructions
Washer Use
The Liquid Bleach Compartment
If desired, measure out the recommended amount of liquid bleach, not
1/3
cup (80 mL), and pour into the right compartment labeled
“LIQUID BLEACH”.
dispensing of the bleach which could result in damaged clothes.
NOTE: Do not use powdered bleach in the dispenser.
The Fabric Softener Compartment
IMPORTANT: Be sure to identify the correct compartment for fabric
If desired, pour the recommended amount of liquid fabric softener into
the compartment labeled “FABRIC SOFTENER”.
Use only liquid fabric softener in the dispenser.
dispensing of the fabric softener which could stain clothes.
NOTE: Do not pour fabric softener directly on the wash load.
22
Washer
Safety
Installation
Instructions
Washer Use
LOADING AND USING THE WASHER
SOIL FABRIC LINT
Lights
Darks
Heavy
Normal
Light
Sturdy Cottons
Lint
Producers
Lint
Collectors
•
items should not be more than half the total wash load.
•
balance load. Add one or two similar items.
•
cause an out-of-balance load.
WARNING
•
with gasoline or other flammable liquids.
•
•
on it (including cooking oils).
•
Close garment zippers, snaps, buttons and hooks.
To avoid tangling tie strings, draw ties and belt-like materials.
•
Mend seams, hems, tears.
•
Empty all items from pockets.
•
•
•
Brush away surface dirt and lint.
•
Promptly wash wet or stained garments to maximize results.
•
Use nylon mesh garment bags to wash small items.
•
•
23
Washer
Safety
Installation
Instructions
Washer Use
To add items after washer has started, press and wait until the door
is unlocked. The washer may take up to 30 seconds to unlock the door
after pressing depending on the machine conditions.
to restart.
CLEANING
EXTERIOR
with sharp objects.
INTERIOR
washer.
1.
2. Open the washer door and pour one cup or 250 mL of liquid bleach or
other washing machine cleaner into the basket.
3.
button.
4.
24
Washer
Safety
Installation
Instructions
Washer Use
5.
would not flood the floor.
A power outage in the house might also
DISPENSER DRAWER AREA
Detergent and fabric softener may build up in the dispenser drawer.
into the left rear corner of the drawer cavity and press down firmly on
25
Washer
Safety
Installation
Instructions
Washer Use
IMPORTANT:
Run Tub Clean with 1 Cup (250mL) of bleach once a month.
•
After the completion of a Tub Clean cycle, the interior of your washer
•
may have a bleach smell.
It is recommended to run a light color load after the Tub Clean cycle.
•
CLEANING THE PUMP FILTER
the pump filter.
Pump
1.
access door.
2. Place a shallow pan or dish under the pump access door and towels on
3. Pull down the pour spout.
Pour
spout
26
Washer
Safety
Installation
Instructions
Washer Use
filter
4.
Pour
spout
5. Clean the debris from the filter.
6.
7. Flip up the pour spout.
8. Close the access door.
27
Washer
Safety
Installation
Instructions
Washer Use
1.
Open the washer door. Using both hands, press down the door gasket.
sure there is nothing blocking the holes behind the gasket.
2.
trapped inside this gasket. Make sure there is nothing blocking the
holes behind the gasket.
3.
this book.
28
Washer
Safety
Installation
Instructions
Washer Use
Certain internal parts are intentionally not grounded and may present a
risk of electric shock only during servicing. Service Personnel - Do not
BEFORE YOU CALL FOR SERVICE...
Troubleshooting Tips
Possible Cause What To Do
Not draining
Not spinning
Not agitating
run drain & spin or rinse
& spin.
• Increase load size if
washing small load
containing heavy and
light items.
Pump clogged
• See page 26 on how to
clean the Pump Filter.
Drain hose is kinked or
• Straighten drain hose and
make sure washer is not
sitting on it.
Household drain may be
clogged
• Check household
to call a plumber.
Drain hose siphoning;
down the drain
• Ensure there is an air gap
between hose and drain.
Door gasket is damaged
• Check to see if gasket
Objects left in pockets
may cause damage to
the washer (nails, screws,
pens, pencils).
Door gasket not damaged
door when the door is
opened. This is a normal
• Carefully wipe off rubber
door seal. Sometimes
dirt or clothing is left in
this seal and can cause a
small leak.
Check back left of washer
for water
condition. Use less
detergent.
29
Washer
Safety
Installation
Instructions
Washer Use
Possible Cause What To Do
(cont.)
Fill hoses or drain hose is
• Make sure hose
washer and faucets and
make sure end of drain
hose is correctly inserted
in and secured to drain
Household drain may be
clogged
• Check household
to call a plumber.
Dispenser clogged
• Powder soap may
cause clogs inside the
dispenser and cause
front of the dispenser.
clean both drawer and
• Use HE and correct
amount of detergent.
Dispenser box crack
Clothes too
wet
run drain & spin or rinse
& spin.
• Increase load size if
washing small load
containing heavy and
light items.
• The machine will slow
the spin speed down to
400 rpm if it has a hard
time balancing the load.
This speed is normal.
Pump clogged
• See page 26 on how to
clean the Pump Filter.
• The dry weight of the
load should be less than
18 lbs.
Drain hose is kinked or
• Straighten drain hose and
make sure washer is not
sitting on it.
30
Washer
Safety
Installation
Instructions
Washer Use
Possible Cause What To Do
Clothes too
wet (cont.)
Household drain may be
clogged
• Check household
to call a plumber.
Drain hose siphoning;
down the drain
• Ensure there is an air gap
between hose and drain.
Incomplete
not advancing
Automatic load
• Timer adds 3 minutes to
11 or 15 rebalances may
the machine will finish
Pump clogged
• See page 26 on how to
clean the Pump Filter.
Drain hose is kinked or
• Straighten the drain hose
and make sure washer is
not sitting on it.
Household drain may be
clogged
• Check household
to call a plumber.
Drain hose siphoning;
down the drain
• Ensure there is an air gap
between hose and drain.
unusual noise;
vibration or
shaking
1/4
transmitted to the floor.
the floor
• Push and pull on the
back right and then back
so they are all firmly
touching the floor and
installer should correct
this problem.
Unbalanced load
• Open door and manually
redistribute load. To
and spin with no load. If
normal, unbalance was
caused by load.
Pump clogged
• See page 26 on how to
clean the Pump Filter.
31
Washer
Safety
Installation
Instructions
Washer Use
Possible Cause What To Do
washer not
working or
dead
Washer is unplugged
• Make sure cord is
plugged securely into a
working outlet.
Water supply is turned off
tripped/blown
• Check house circuit
fuses or reset breaker.
checks
• First time the washer is
checks occur. It may take
Snags, holes,
tears, rips
wear
• The dry weight of the
load should be less than
18 lbs.
Pens, pencils, nails,
left in pockets
pockets.
Pins, snaps, hooks, sharp
buttons, belt buckles,
zippers and sharp objects
left in pockets
• Fasten snaps, hooks,
buttons and zippers.
changes
This is normal
• During spin the washer
may need to rebalance
the load sometimes
increased causing time
Not enough
water
This is normal
• Horizontal washers do
not require the tub to fill
washers.
Washer
pauses or
has to be
washer door
is locked and
will not open
Pump clogged
• See page 26 on how to
clean the Pump Filter.
32
Washer
Safety
Installation
Instructions
Washer Use
Possible Cause What To Do
Door unlocks
and machine
doesn’t
operate
This is normal
• Front load washers start
load washers, and it takes
30 seconds to check the
and unlock.
• Simply open and close
the door firmly; then
press
Water does
not enter
washer or
enters slowly
checks
• After is pressed,the
after is pressed.
Turn the water source off
Water supply is turned off
stopped up
connection hoses from
the upper back of the
washer. Use a brush or
toothpick to clean the
(like work clothes) with
light items (like blouses).
water that is too hot
33
Washer
Safety
Installation
Instructions
Washer Use
.
Possible Cause What To Do
clothes
Not enough detergent
• Use correct amount of
detergent.
Not using HE (high-
• Use HE detergent.
Hard water
install a water softener.
Use a water conditioner or
Detergent is not
dissolving
• Try a liquid detergent.
• Sort clothes by color. If
softener
• Check fabric softener
using dispenser.
• Sort whites or lightly
colored items from dark
colors.
load from washer.
Slight
variation in
metallic color
This is normal appearance
• Due to the metallic
properties of paint used
may occur due to viewing
angles and lighting
conditions.
34
Washer
Safety
Installation
Instructions
Washer Use
Possible Cause What To Do
Smell inside Washer unused for a
long time, not using
HE detergent or used too
much detergent
once a month.
• In the case of strong
more than once a month.
• Use only the amount of
detergent recommended
on the detergent
container.
• Use only HE (high-
items from the washer
promptly after machine
stops running.
is necessary if this
appliance is used by or
near children. Do not
allow children to play on,
with or inside this or any
Detergent
leak detergent insert
• Make sure detergent insert
dispensing of
softener or
bleach
Dispenser clogged
• Monthly clean the
dispenser drawer to
chemicals.
Softener or bleach is
correct amount of softener
or bleach.
Softener or bleach cap
issue
• Make sure softener and
• Make sure to have the
work.
35
Washer
Safety
Installation
Instructions
Washer Use
ERROR CODES
Description Solution
E30
Door is not closed
closed.
• Check if the clothes are
• Check if the water
• Straighten the water hoses.
• Check if the inlet valve
stuck.
E10
while washing
pressure is too low.
filter is blocked.
E21
• Check if the drain hose is
• Restart the washer.
blocked, clean drain filter.
E12
EXX
Others
• Please try again first, call
up service line if there are
still troubles.
36
Washer
Safety
Installation
Instructions
Washer Use
*
required
