MODEL: DFI041ARU-07
© 2024, Twin-Star International, Inc.
Boca Raton, FL 33487
VOLTAGE
120 VAC, 60 Hz
AMPS 12.5 Amps
WATTS 1500 Watts
PRODUCT SPECIFICATIONS
OPERATING INSTRUCTIONS
For Customer Service:
tsicustomerservice.com
1-888-674-7517
8:30 a.m.-5:30 p.m., EST, Monday-Friday
Manufactured and distributed by Twin-Star International, Inc., under license from
Duraflame, Inc. duraflame, the flame symbol and logo are registered trademarks of
Duraflame, Inc.
Note: When rst running the heater there may
be an odor. This is normal as the heater has a
surface coating on the internal parts. For the
rst several hours of operation, the coating
reacts with the internal parts to permanently
protect them. The odor is safe; if you are
sensitive to the odor, it is recommended
to run the heater in a well-ventilated area until
the odor dissipates.
Warning: This is an unvented, electric appliance.
DO NOT attempt to burn wood or manufactured
relogs in or on this appliance or grate.
Go to tsicustomerservice.com for product warranty registration
POWER
FLAME
HEATER
THERMOSTAT
FLAME SOUND
The MAIN POWER switch supplies power to all of the functions of the replace. The
switch must be in the ON position for any functions or the remote to work.
OPERATING INSTRUCTIONS
Each time the FLAME button is pressed, the intensity of the ame decreases. There are
ve brightness levels that can be selected.
The HEATER button will turn ON/OFF the heater.
1. The thermostat knob controls the thermostat setting.
2. Turning the knob clockwise will increase thermostat setting. Rotating the knob
counter-clockwise will decrease the thermostat setting.
3. When the heater reaches the thermostat setting it will turn off until the room cools
at which point the heater will turn back on.
There are 3 volume levels that can be selected and OFF.
1. Low volume 2. Medium volume 3. High volume
IMPORTANT INSTRUCTIONS
SAVE THESE INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce the risk of re, electrical shock, iinjury to persons, and hyperthermia,
including the following:
C2572
THERMOSTAT
HEATER
FLAME
MAIN POWER SWITCH
FLAME SOUND
FLAME SOUND
POWER
HEATER
FLAME
The replace can be operated by either the remote control or the control panel.
1. The battery compartment is located on the back end of the remote
control.
2. Press and slide the battery door open and remove the old battery.
3. Insert 2 AAA batteries, checking that the + and - sides of the battery
match inside the battery compartment.
4. Replace the battery compartment door.
Caution:
• For best results, use 2pcs AAA alkaline batteries.
• Install only new batteries of the same type in your product.
• Failure to insert batteries in the correct polarity, as indicated in the
battery compartment, may shorten the life of the batteries or cause
batteries to leak.
• Do not mix old and new batteries.
• Do not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel
Cadmium) or (Nickel Metal Hydride) batteries.
• Danger of explosion if battery is incorrectly replaced.
• Do not ingest batteries.
• Batteries should be recycled or disposed of as per state and local
guidelines.
DISPOSAL OF USED BATTERIES
Battery may contain hazardous substances which could endanger the
enviroment and human health. Used batteries shall not be treated as
municipal waste, but left at the appropriate collection point for recycling.
For more information about collection and recycling of used batteries,
please contact your local municipality or waste disposal service.
BATTERY REPLACEMENT
Note:
Battery disposal
Please always dispose of batteries
at a suitable recycling point.
AAA 1.5V
AAA 1.5V
1. Read all instructions before using this appliance.
2. DANGER - High temperatures may be generated under certain abnormal
conditions. Do not partially or fully cover or obstruct the front of this heater.
WARNING: In order to avoid overheating, do not cover the heater.
3. Extreme caution is necessary when any heater is used by or near children or
invalids and whenever the heater is left operating and unattended.
4. Always unplug heater when not in use.
5. Do not operate any heater with a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged in any manner. Discard heater,
or return to authorized service facility for examination and/or repair.
6. Do not use outdoors.
7. This appliance is not intended for use in bathrooms, laundry areas and
similar indoor locations. Never locate heater where it may fall into a bathtub
or other water container.
8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners,
or similar coverings. Do not route cord under furniture or appliances. Arrange
cord away from trafc area and where it will not be tripped over.
9. To disconnect this appliance, turn controls to the off position, then remove
plug from outlet.
10. Do not insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock or re, or damage the
appliance.
11. To prevent a possible re, do not block air intakes or exhaust in any manner.
Do not use on soft surfaces, like a bed, where opening may become blocked.
12. This appliance has hot and arcing or sparking parts inside. Do not use it in
areas where gasoline, paint, or ammable liquids are used or stored.
13. Use this appliance only as described in the manual. Any other use not recommended
by the manufacturer may cause re, electric shock or injury to persons.
14. This product is equipped with a polarized plug (one blade is wider than the other
blade). To reduce the risk of electrical shock, this plug will t into a polarized outlet
only one way. This is a safety feature. If you are unable to insert the plug into the
electrical outlet, try reversing the plug. If the plug still does not t, contact a qualied
electrician. Always plug heaters directly into a wall outlet/ receptacle.Never use with
an extension cord or relocatable power tap( oulet/power strip).
15. Hyperthermia can result in death. Symptoms of hyperthermia include high body
temperature, headache, nausea, vomiting, tiredness, dizziness, fainting, and rapid
pulse. If you begin to experience symptoms related to hyperthermia, turn off the
heater and seek medical attention.
16. To avoid excessive room temperatures which can cause hyperthermia: DO NOT
leave product running unattended in a conned space around infants, or individuals
with reduced physical, sensory, or mental capabilities.
17. This heater may include a visual alarm to warn that parts of the heater are getting
excessively hot. If the alarm ashes immediately turn the heater off and inspect for
any objects on or adjacent to the heater that may cause high temperatures.
DO NOT OPERATE THE HEATER WITH THE ALARM FLASHING!
INSTALLATION INSTRUCTIONS
When placing the heater in a smaller space, follow these
guidelines to prevent the unit from overheating. Make sure that
no objects are sitting closer than 20 inches to the front of the
heater.
Clearance
Sides............................2 inch
Top...............................5 inch
Back.............................2 inch
Wall
Side
Min. 2 inch
Side
Min. 2 inch
Back
Min. 2 inch
Top
Min. 5 inch
Warning: Do not cover or partially obstruct the heater outlet
(front of the unit where heat is expelled). Glass replace doors
and mesh screens, small lips or retaining walls in replaces,
and even objects placed in front of the heater like candles,
drinks, or knick knacks can obstruct the heat expulsion and
cause overheating of the unit.
MODEL: DFI041ARU-07
© 2024, Twin-Star International, Inc.
Boca Raton, FL 33487
VOLTAGE
120 VAC, 60 Hz
AMPS 12.5 Amps
WATTS 1500 Watts
PRODUCT SPECIFICATIONS
OPERATING INSTRUCTIONS
For Customer Service:
tsicustomerservice.com
1-888-674-7517
8:30 a.m.-5:30 p.m., EST, Monday-Friday
Manufactured and distributed by Twin-Star International, Inc., under license from
Duraflame, Inc. duraflame, the flame symbol and logo are registered trademarks of
Duraflame, Inc.
Note: When rst running the heater there may
be an odor. This is normal as the heater has a
surface coating on the internal parts. For the
rst several hours of operation, the coating
reacts with the internal parts to permanently
protect them. The odor is safe; if you are
sensitive to the odor, it is recommended
to run the heater in a well-ventilated area until
the odor dissipates.
Warning: This is an unvented, electric appliance.
DO NOT attempt to burn wood or manufactured
relogs in or on this appliance or grate.
Go to tsicustomerservice.com for product warranty registration
POWER
FLAME
HEATER
THERMOSTAT
FLAME SOUND
The MAIN POWER switch supplies power to all of the functions of the replace. The
switch must be in the ON position for any functions or the remote to work.
OPERATING INSTRUCTIONS
Each time the FLAME button is pressed, the intensity of the ame decreases. There are
ve brightness levels that can be selected.
The HEATER button will turn ON/OFF the heater.
1. The thermostat knob controls the thermostat setting.
2. Turning the knob clockwise will increase thermostat setting. Rotating the knob
counter-clockwise will decrease the thermostat setting.
3. When the heater reaches the thermostat setting it will turn off until the room cools
at which point the heater will turn back on.
There are 3 volume levels that can be selected and OFF.
1. Low volume 2. Medium volume 3. High volume
IMPORTANT INSTRUCTIONS
SAVE THESE INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce the risk of re, electrical shock, iinjury to persons, and hyperthermia,
including the following:
C2572
THERMOSTAT
HEATER
FLAME
MAIN POWER SWITCH
FLAME SOUND
FLAME SOUND
POWER
HEATER
FLAME
The replace can be operated by either the remote control or the control panel.
1. The battery compartment is located on the back end of the remote
control.
2. Press and slide the battery door open and remove the old battery.
3. Insert 2 AAA batteries, checking that the + and - sides of the battery
match inside the battery compartment.
4. Replace the battery compartment door.
Caution:
• For best results, use 2pcs AAA alkaline batteries.
• Install only new batteries of the same type in your product.
• Failure to insert batteries in the correct polarity, as indicated in the
battery compartment, may shorten the life of the batteries or cause
batteries to leak.
• Do not mix old and new batteries.
• Do not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel
Cadmium) or (Nickel Metal Hydride) batteries.
• Danger of explosion if battery is incorrectly replaced.
• Do not ingest batteries.
• Batteries should be recycled or disposed of as per state and local
guidelines.
DISPOSAL OF USED BATTERIES
Battery may contain hazardous substances which could endanger the
enviroment and human health. Used batteries shall not be treated as
municipal waste, but left at the appropriate collection point for recycling.
For more information about collection and recycling of used batteries,
please contact your local municipality or waste disposal service.
BATTERY REPLACEMENT
Note:
Battery disposal
Please always dispose of batteries
at a suitable recycling point.
AAA 1.5V
AAA 1.5V
1. Read all instructions before using this appliance.
2. DANGER - High temperatures may be generated under certain abnormal
conditions. Do not partially or fully cover or obstruct the front of this heater.
WARNING: In order to avoid overheating, do not cover the heater.
3. Extreme caution is necessary when any heater is used by or near children or
invalids and whenever the heater is left operating and unattended.
4. Always unplug heater when not in use.
5. Do not operate any heater with a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged in any manner. Discard heater,
or return to authorized service facility for examination and/or repair.
6. Do not use outdoors.
7. This appliance is not intended for use in bathrooms, laundry areas and
similar indoor locations. Never locate heater where it may fall into a bathtub
or other water container.
8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners,
or similar coverings. Do not route cord under furniture or appliances. Arrange
cord away from trafc area and where it will not be tripped over.
9. To disconnect this appliance, turn controls to the off position, then remove
plug from outlet.
10. Do not insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock or re, or damage the
appliance.
11. To prevent a possible re, do not block air intakes or exhaust in any manner.
Do not use on soft surfaces, like a bed, where opening may become blocked.
12. This appliance has hot and arcing or sparking parts inside. Do not use it in
areas where gasoline, paint, or ammable liquids are used or stored.
13. Use this appliance only as described in the manual. Any other use not recommended
by the manufacturer may cause re, electric shock or injury to persons.
14. This product is equipped with a polarized plug (one blade is wider than the other
blade). To reduce the risk of electrical shock, this plug will t into a polarized outlet
only one way. This is a safety feature. If you are unable to insert the plug into the
electrical outlet, try reversing the plug. If the plug still does not t, contact a qualied
electrician. Always plug heaters directly into a wall outlet/ receptacle.Never use with
an extension cord or relocatable power tap( oulet/power strip).
15. Hyperthermia can result in death. Symptoms of hyperthermia include high body
temperature, headache, nausea, vomiting, tiredness, dizziness, fainting, and rapid
pulse. If you begin to experience symptoms related to hyperthermia, turn off the
heater and seek medical attention.
16. To avoid excessive room temperatures which can cause hyperthermia: DO NOT
leave product running unattended in a conned space around infants, or individuals
with reduced physical, sensory, or mental capabilities.
17. This heater may include a visual alarm to warn that parts of the heater are getting
excessively hot. If the alarm ashes immediately turn the heater off and inspect for
any objects on or adjacent to the heater that may cause high temperatures.
DO NOT OPERATE THE HEATER WITH THE ALARM FLASHING!
INSTALLATION INSTRUCTIONS
When placing the heater in a smaller space, follow these
guidelines to prevent the unit from overheating. Make sure that
no objects are sitting closer than 20 inches to the front of the
heater.
Clearance
Sides............................2 inch
Top...............................5 inch
Back.............................2 inch
Wall
Side
Min. 2 inch
Side
Min. 2 inch
Back
Min. 2 inch
Top
Min. 5 inch
Warning: Do not cover or partially obstruct the heater outlet
(front of the unit where heat is expelled). Glass replace doors
and mesh screens, small lips or retaining walls in replaces,
and even objects placed in front of the heater like candles,
drinks, or knick knacks can obstruct the heat expulsion and
cause overheating of the unit.
TROUBLESHOOTING GUIDE
MODEL: DFI041ARU-07
EXPLODED VIEW
CARE AND MAINTENANCE
C2572
Problem Root Cause Corrective Action
1. No power, switches do not
light up.
1. Power cord was not plugged
into the outlet.
1. Check that unit is plugged directly into a standard 120 volt outlet.
2. Logs glow, but ame effect
does not work.
2. Spinner motor is defective. 2. Check whether Flame Generator drive motor is running.
3. Flame effect operates,
but heater does not blow
warm air.
3a. Heater is not on powered ON.
4a. Temperature is set at low.
3a.Try pressing the ON/OFF HEATER button several times to make
sure it is in the ON position.
3b. Make sure that the TEMPERATURE knob is set to the max setting.
4. The heater shut off and
won’t come back on, or
the ickering lights of
ame and logs.
4. Manual Reset Triggered.
4. Turn the POWER to “OFF” and unplug the unit from the wall outlet
for 5 minutes. After 5 minutes plug the unit back into wall outlet,
and operate as normal. If the problem persists contact customer
service.
5. Power cord gets warm. 5. Power cord plug overheating.
5. Check your heater cord and plug connections. Faulty wall
outlet connections or loose plugs can cause the outlet or plug to
overheat. Be sure the plug ts tight in the outlet. Heaters draw
more current than small appliances, overheating of the outlet may
occur even if it has not occurred with the use of other appliances.
During use check frequently to determine if your plug outlet or
faceplate is HOT! If so, discontinue use of the heater and have a
qualied electrician check and/or replace the faulty outlet(s).
6. No ames sound, but
have ames effect.
6a. Sound button turned off.
6b. Loose terminal blocks or
damaged loudspeaker
6a. Press Sound button several times.
6b. Must be replaced by the manufacturer, contact customer service
for a replacment.
7. Remote control is not work-
ing.
7a. No batteries.
7b. Poor Signal.
7c. Distance.
7a. Change the remote batteries.
7b.Operate remote transmitter at a slow measured pace. Press the
remote control buttons with an even motion and gentle pressure.
Repeatedly pressing buttons in rapid succession may cause the
transmitter to malfunction.
7c.Operate the remote at a distance less than 20 feet from the front of
the appliance; point the remote at the control panel.
8. Unit continues to run after
reaching set temperature/
or powering off.
8a. Cool down cycle.
8a. Normal operation, will continue to run for several minutes before
shutting down. Times will vary based on heating. UNIT WILL
BLOW COOL AIR.
9. Flame effect works but
heater function does not
and the emberbed ashes
when the heater button is
pressed.
9a. The heater is disabled.
9a.With the power on, press and hold the heater button on the control
panel for 10 seconds. Once reenabled the emberbed lights will
ash multiple times.
• Clean the trim using a soft cloth, slightly dampened with citrus oil based product and buff with a clean soft cloth.
• DO NOT use brass polish or household cleaners as these products will damage the metal trim. Citrus oil based products can be obtained at
supermarkets or hardware stores.
• WARNING: Electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of re, electrical
shock and injury to persons.
• WARNING: Disconnect power before attempting any maintenance or cleaning to reduce the risk of re, electrical shock or personal injury.
Part Part Name Part Number
1 Remote P198
FCC/IC INFORMATION
Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
Twin-Star International Inc.
750 Park of Commerce Blvd Suite 400
Boca Raton, FL 33487
1-888-674-7517
The manufacturer warrants that your new Electric Stove is free from manufacturing and material defects for a period of one year from date of puchase, subject to
the following conditions and limitations.
1. Install and operate this Electric Stove in accordance with the installation and operating instructions furnished with the product at all times. Any unauthorized
repair, alteration, willful abuse, accident, or misuse of the product shall nullify this warranty.
2. This warranty is non-transferable, and is made to the original owner, provided that the purchase was made through an authorized supplier of the product.
3. The warranty is limited to the repair or replacement of part(s) found to be defective in material or workmanship, provided that such part(s) have been subjected
to normal conditions of use and service, after said defect is conrmed by the manufacturer’s inspection.
4. The manufacturer may, at its discretion, fully discharge all obligations with respect to this warranty by refunding the wholesale price of the defective part(s).
5. Any installation, labor, construction, transportation, or other related costs/expenses arising from defective part(s), repair, replacement, or otherwise of same, will
not be covered by this warranty, nor shall the manufacturer assume responsibility for same.
6. The owner/user assumes all other risks, if any, including the risk of any direct, indirect or consequential loss or damage arising out of the use, or inability to use
the product, except as provided by law.
7. All other warranties – expressed or implied –with respect to the product, its components and accessories, or any obligations/liabilities on the part of the
manufacturer are hereby expressly excluded.
8. The manufacturer neither assumes, nor authorizes any third party to assume on its behalf, any other liabilities with respect to the sale of the product.
9. The warranties as outlined within this document do not apply to non accessories used in conjunction with the installation of this product.
10.This warranty gives you specic legal rights, and you may also have other rights which vary from state to state.
This warranty is void if:
a. The replace is subjected to prolonged periods of dampness or condensation.
b. Any unauthorized alteration, willful abuse, accident, or misuse of the product.
c. You do not have the original receipt of purchase.
IF WARRANTY SERVICE IS NEEDED
Contact the manufacturer by calling customer service department at 1-888-674-7517, 7 days a week 24 hours a day at our toll-free help line. Our Consumer
Service department is available Monday – Friday 8:30 am – 5:30 pm EST. Make sure you have your warranty, your sales receipt, location of purchase and the
model/serial number of your product.
1-YEAR LIMITED WARRANTY
TROUBLESHOOTING GUIDE
MODEL: DFI041ARU-07
EXPLODED VIEW
CARE AND MAINTENANCE
C2572
Problem Root Cause Corrective Action
1. No power, switches do not
light up.
1. Power cord was not plugged
into the outlet.
1. Check that unit is plugged directly into a standard 120 volt outlet.
2. Logs glow, but ame effect
does not work.
2. Spinner motor is defective. 2. Check whether Flame Generator drive motor is running.
3. Flame effect operates,
but heater does not blow
warm air.
3a. Heater is not on powered ON.
4a. Temperature is set at low.
3a.Try pressing the ON/OFF HEATER button several times to make
sure it is in the ON position.
3b. Make sure that the TEMPERATURE knob is set to the max setting.
4. The heater shut off and
won’t come back on, or
the ickering lights of
ame and logs.
4. Manual Reset Triggered.
4. Turn the POWER to “OFF” and unplug the unit from the wall outlet
for 5 minutes. After 5 minutes plug the unit back into wall outlet,
and operate as normal. If the problem persists contact customer
service.
5. Power cord gets warm. 5. Power cord plug overheating.
5. Check your heater cord and plug connections. Faulty wall
outlet connections or loose plugs can cause the outlet or plug to
overheat. Be sure the plug ts tight in the outlet. Heaters draw
more current than small appliances, overheating of the outlet may
occur even if it has not occurred with the use of other appliances.
During use check frequently to determine if your plug outlet or
faceplate is HOT! If so, discontinue use of the heater and have a
qualied electrician check and/or replace the faulty outlet(s).
6. No ames sound, but
have ames effect.
6a. Sound button turned off.
6b. Loose terminal blocks or
damaged loudspeaker
6a. Press Sound button several times.
6b. Must be replaced by the manufacturer, contact customer service
for a replacment.
7. Remote control is not work-
ing.
7a. No batteries.
7b. Poor Signal.
7c. Distance.
7a. Change the remote batteries.
7b.Operate remote transmitter at a slow measured pace. Press the
remote control buttons with an even motion and gentle pressure.
Repeatedly pressing buttons in rapid succession may cause the
transmitter to malfunction.
7c.Operate the remote at a distance less than 20 feet from the front of
the appliance; point the remote at the control panel.
8. Unit continues to run after
reaching set temperature/
or powering off.
8a. Cool down cycle.
8a. Normal operation, will continue to run for several minutes before
shutting down. Times will vary based on heating. UNIT WILL
BLOW COOL AIR.
9. Flame effect works but
heater function does not
and the emberbed ashes
when the heater button is
pressed.
9a. The heater is disabled.
9a.With the power on, press and hold the heater button on the control
panel for 10 seconds. Once reenabled the emberbed lights will
ash multiple times.
• Clean the trim using a soft cloth, slightly dampened with citrus oil based product and buff with a clean soft cloth.
• DO NOT use brass polish or household cleaners as these products will damage the metal trim. Citrus oil based products can be obtained at
supermarkets or hardware stores.
• WARNING: Electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of re, electrical
shock and injury to persons.
• WARNING: Disconnect power before attempting any maintenance or cleaning to reduce the risk of re, electrical shock or personal injury.
Part Part Name Part Number
1 Remote P198
FCC/IC INFORMATION
Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
Twin-Star International Inc.
750 Park of Commerce Blvd Suite 400
Boca Raton, FL 33487
1-888-674-7517
The manufacturer warrants that your new Electric Stove is free from manufacturing and material defects for a period of one year from date of puchase, subject to
the following conditions and limitations.
1. Install and operate this Electric Stove in accordance with the installation and operating instructions furnished with the product at all times. Any unauthorized
repair, alteration, willful abuse, accident, or misuse of the product shall nullify this warranty.
2. This warranty is non-transferable, and is made to the original owner, provided that the purchase was made through an authorized supplier of the product.
3. The warranty is limited to the repair or replacement of part(s) found to be defective in material or workmanship, provided that such part(s) have been subjected
to normal conditions of use and service, after said defect is conrmed by the manufacturer’s inspection.
4. The manufacturer may, at its discretion, fully discharge all obligations with respect to this warranty by refunding the wholesale price of the defective part(s).
5. Any installation, labor, construction, transportation, or other related costs/expenses arising from defective part(s), repair, replacement, or otherwise of same, will
not be covered by this warranty, nor shall the manufacturer assume responsibility for same.
6. The owner/user assumes all other risks, if any, including the risk of any direct, indirect or consequential loss or damage arising out of the use, or inability to use
the product, except as provided by law.
7. All other warranties – expressed or implied –with respect to the product, its components and accessories, or any obligations/liabilities on the part of the
manufacturer are hereby expressly excluded.
8. The manufacturer neither assumes, nor authorizes any third party to assume on its behalf, any other liabilities with respect to the sale of the product.
9. The warranties as outlined within this document do not apply to non accessories used in conjunction with the installation of this product.
10.This warranty gives you specic legal rights, and you may also have other rights which vary from state to state.
This warranty is void if:
a. The replace is subjected to prolonged periods of dampness or condensation.
b. Any unauthorized alteration, willful abuse, accident, or misuse of the product.
c. You do not have the original receipt of purchase.
IF WARRANTY SERVICE IS NEEDED
Contact the manufacturer by calling customer service department at 1-888-674-7517, 7 days a week 24 hours a day at our toll-free help line. Our Consumer
Service department is available Monday – Friday 8:30 am – 5:30 pm EST. Make sure you have your warranty, your sales receipt, location of purchase and the
model/serial number of your product.
1-YEAR LIMITED WARRANTY
