BC533
Mounting
Your M16 Electro Sight has a built in standard 5/8 mount. This mount will
attach your sight to your firearm.
1. Loosen the clamp bolts on the mount. Turn counter clockwise.
2. Now place the mount on the rail of the the riflescope.
3. Tighten the bolts but make sure that you do not tighten them all the way.
4. Look through the sight and adjust it, by puling the sight forwards and
backwards. Do this until the full field of view is in focus.
5. Once your able to see the entire field of view tighten the mount all
the way.
Battery
The M16 Electro Sight comes equipped with 2 LR44
button cell batteries. Each battery has a voltage of 1.5
volts. The battery compartment is located on the mount
and is directly under the eyepiece.
Changing the Battery
When your M16 Electro Sight becomes dim or will not light at all:
1. Remove the battery compartment cap off, by twisting the cap counter
clockwise.
2. Once the cap is off and the old batteries have been removed place the
new batteries into the compartment positive (+) side up.
3. Replace the cap back on and turn clockwise. Ensure that you place the
cap on tightly. This will help keep moisture out of the Electro Sight.
On/Off
1. To turn on sight press R/G Button located on side
of mount.
2. Press again to change from Red to Green or Green to
Red dot. Can use + / - to adjust the intensity of
the dot.
3. Press and hold until dot disappears to turn off the sight
Windage and Elevation
You can find the windage on the right side of the sight. This adjusts the
horizontal axis of the sight.
The elevation is located on the top of the sight. This adjusts the vertical
axis of the sight.
Warning: Never attempt to look into
the sun with this or any other optical
enhancing device. Doing so may
cause severe and permanent eye
damage. Always follow safe firearm
handling procedures when using or
handling a firearm.
1x30 Electro Sight
Continued on next page
©2017 BARSKA®BC291
ELECTRO SIGHT / RED DOT
Optics, as manufacturer, warrants this new precision optical product to be
free of original defects in materials and/or workmanship for the length of time
specified by this warranty. This warranty does not include damage caused by
abuse, improper handling, installation, maintenance, normal wear-and-tear,
unauthorized repairs or modifications and tampering in anyway.
This warranty is limited to the original purchaser and is not transferable. This
warranty applies only to products purchased in the United States of America.
In the event of a defect within 30 days, the consumer must return the
defective unit to the BARSKA dealer (the place of purchase) at his/her own
expense.
Beyond 30 days, BARSKA products should be sent to the following address
for
warranty repairs. Products must be packed carefully and sturdily to prevent
damage in transit, and returned freight prepaid to:
BARSKA® OPTICS
Repair Department
855 Towne Center Drive
Pomona, CA 91767
For additional and updated information
please visit our website at www.barska.com
Please email [email protected] or call 1-888-666-6769 for Return
Merchandise Number (RMA#) before any returns.
NOTE: All merchandise received without a valid RMA # will be returned to
shipper at his/her own expense.
Please include all of the following when returning BARSKA products for
service and/or replacement:
1. Please write your complete details (Name, Address, Telephone #, E-mail
address, RMA#, etc.)
2. Purchase receipt or Proof of Purchase. (Original/Copy)
3. A brief explanation of the defect.
4. A Check/Money Order of $20.00 to cover inspection, shipping and
handling.
*Please allow 6-8 weeks for delivery.
This product will either be replaced or repaired at the discretion of the
warrantor. If it's a discontinued item, we will replace the product with an
equivalent product. Should the repair not be covered by this warranty, an
estimate will be sent for your approval. Non-warranty repairs or refurbishing of
your optical products are always provided at a reasonable cost.
BARSKA® Optics shall not be liable for any consequential, incidental and/or
contingent damages whatsoever. We will not pay shipping, insurance or
transportation charges from you to us, or any import fees, duties and or taxes.
This warranty supersedes all previous BARSKA® Optics warranties.
1 YEAR LIMITED WARRANTY
To access the windage and elevation turrets, remove the caps that cover
the turrets. Turn counter clockwise to loosen the caps. Once the turrets are
exposed, use a small coin to turn the turrets.
Windage
Turn the turret counter clockwise to raise the reticle.
Turn the turret clockwise to lower the reticle.
Elevation
Turn the turret counter clockwise to make the reticle move to the right. Turn
the turret clockwise to make the reticle move to the left.
