User’s Manual for
Depository Safe
www.barska.com
BC778 8/23
2
3
Read all instructions before using this safe.
WARNING
- For security purposes, change the factory default Master Code as soon as possible.
Factory default Master Code is: 12345678
- The Master Code should always be held by the owner of the safe or
authorized people. If the Master Code is forgotten, the user is unable to
change new Master Code, Activate/ Delete Users, set up Single/Dual Entry
Modes, and set up Time Delay Mode.
- Test registered pin codes a few times before closing the door.
- Test and store emergency keys in a secure place; NOT inside of the safe.
- Be careful when opening and closing the depository slot.
- Keep children away from safe; they should not play with or around the safe at
any time.
- Always make sure the safe is locked before walking away. Avoid leaving the safe
door open and unattended; it will allow unauthorized individuals to reprogram the
safe, gaining full access to the safe and its contents.
- Test and make sure the safe works properly before mounting. Once tested, mount
the safe before use.
NOTE: Barska is not responsible for any installation damages and any lost or
stolen contents.
CONTENTS
Warnings 3
Parts Of The Safe 4
Battery and Key Access 4
Changing the Master Code 6
Register User Code 6
Change User Code 6
Delete User Code 7
Setting Single User and Dual User Mode 7
Opening and Locking Safe with User Code /Master Code 8
What’s the Time Delay Feature 8
Setting Time Delay (1-59 minutes time delay) 8
Lock Out Mode 9
Low Battery Warning 9
Trouble Shooting 9
Care And Maintenance 10
Mounting Instructions 10
Warranty 11
4
5
BATTERY & KEY ACCESS
Install Battery
1. The battery cover is located on the
bottom edge of the keypad. Remove
the cover by pulling on the tab.
2. Carefully insert one new 9V alkaline
battery into the battery compartment.
Do NOT force the battery into
the compartment.
3. Reinstall the battery cover.
NOTE: Do NOT pull the battery
connector to avoid pulling wires out
of housing.
Key Access
The key access is concealed yet and easy to access in case of an emergency or
forgotten PIN code.
*NOTE: Before you start to use the safe, test the emergency keys and store them in
a secure place, NOT inside of the safe
PARTS OF THE SAFE 1. Use a Phillip’s Head screw driver to remove the screw on the top of keypad cover
2. Carefully remove the keypad cover from the housing. Let the keypad cover hang
with the wires still attached
3. Locate the key access inside of the housing. Insert the key into key slot and
turn clockwise to open safe.
4. After opening the safe, reinstall the keypad cover and screw down the cover with
the housing.
A. Handle
B. Indicator Lights
C. Keypad
D. Battery Compartment (located behind keypad)
E. Emergency Key Access (located behind keypad)
F. Sealed Envelope (Include Reset to factory default instruction and
initialization button)
NOTE: For security purposes, reset to factory default instruction and initialization
button are in the Sealed Envelope. Please keep it with the owner or authorized
manager in a secured place, NOT inside of the safe.
Handle
Locked Position
Handle
Unlocked Position
6
7
CHANGING THE MASTER CODE (Code length: 3-8 digits)
NOTE: Always perform this operation with the door opened. Test new code a couple
of times before closing the door. Safe retains 1 master code
Step 1: Press “ * * “ → 2 short beeps with Yellow light
Step 2: Press “8 8 8 #” → 2 short beeps with Yellow light
Step 3: Input “Current Master Code #” → 2 short beeps with Yellow light
(For 1st time to use, Current Master Code is Factory default code 12345678)
Step 4: Input “New Master Code #” → 2 short beeps with Yellow/Red lights
Step 5: Re-Input “New Master Code #” → 2 short beeps with Green light on for
3 seconds
Example: ** 888 # Current Master Code # New Master Code # New Master Code #
If the master code did not save successfully, the lock will beep 5 times with Red light.
The old code is still valid. Please repeat steps 1-5.
REGISTER USER CODES (Code length: 3-8 digits)
Safe retains 5 user codes
Step 1: Press “* * “→ 2 short beeps with Yellow light
Step 2: Press “3 3 3 #” → 2 short beeps with Yellow light
Step 3: Input “Current Master Code #” → 2 short beeps with Yellow light
Step 4: Input “User No. #” →1 short beep with Yellow/Red lights
(User No.: Specify which user you would like to register 1,2,3,4 or 5)
Step 5: Input “New User Code #” →2 short beeps with Yellow/Red lights
Step 6: Re-Input “New User Code #” → 2 short beeps with Green light on for
3 seconds. User code Registration is completed.
CHANGE USER CODES
Step 1: Press “ * * “ → 2 short beeps with Yellow light
Step 2: Press “4 4 4 #” → 2 short beeps with Yellow light
Step 3: Input “Current User Code #” → 2 short beeps with Yellow light
Step 4: Input “User No. #” →1 short beep with Yellow/Red lights
(User No.: Enter the User No. that identies the Current User Code
on Step 3)
Step 5: Input “New User Code #” →2 short beeps with Yellow/Red light
Step 6: Re-Input “New User Code #” → 2 short beeps with Green light
User code change is completed.
DELETE USER CODES
Step 1: Press “* * “→ 2 short beeps with Yellow light
Step 2: Press “666 #“ → 2 short beeps with Yellow light
Step 3: Input “Current Master Code# “ → 2 short beeps with Yellow light
Step 4: Input “User No.#” → 1 short beep with Yellow/Red lights
Step 5: Re-Input “User No.#” → 2 short beeps with Green light
User code delete is completed.
Note: If the user code did not delete successfully, the lock will beep 5 times. Please
repeat steps.
SETTING SINGLE USER & DUAL USER MODES
Single User Mode
This mode will require enter Only ONE valid user code to open the safe
Step 1: Press “ * * “ → 2 short beeps with Yellow light
Step 2: Press “158 # “ → 2 short beeps with Yellow light
Step 3: Input “ Current Master Code# ” → 2 short beeps with Yellow light
Step 4: Press “ 1# “ → 2 short beeps with Green light
This Operation will set the safe to Single User Mode, please test after set up. If the
Single User Mode did not set successfully, the lock will beep 5 times. Please repeat
steps.
Dual User Mode
This mode will require enter any TWO valid user codes to open the safe.
Note: Master code does not require another code to open safe under Dual User
mode.
Step 1: Press “ * * “ → 2 short beeps with Yellow light
Step 2: Press “158#“ → 2 short beeps with Yellow light
Step 3: Input “ Current Master Code# ” → 2 short beeps with Yellow light
Step 4: Press “ 2# “→ 2 short beeps with Green light.
This Operation will set the safe to Dual user mode and require to put 2 user
codes to open the safe, please test after set up. If the Dual User Mode did not set
successfully, the lock will beep 5 times. Please repeat steps.
8
9
OPENING AND LOCKING SAFE WITH USER CODE/ MASTER CODE
Open
Single User Mode (Default Setting)
Step 1: Press “User Code or Master Code #” → Green light on for 5 seconds
Step 2: Turn the handle clockwise before the green light turns off
Dual User Mode (Please refer to Setting Single User & Dual User Mode)
Step 1: Press “1st Code #” → 2 short beeps with Yellow light
Step 2: Press “2nd Code #” → Green light on for 5 seconds
Step 3: Turn the handle clockwise before the green light turns off
NOTE: Master code does not require another code to open safe under Dual User
mode.
Lock
Close the safe door and turn the handle to the locked position
WHAT‘S TIME DELAY FEATURE
The time delay lock is a timer designed to prevent the opening of the safe until it
reaches the pre-set time, even if the correct combinations are known. The feature
was originally created to prevent criminals from using a person or employee who
knows the valid combination in order to gain access to the safe.
SETTING TIME DELAY (1-59 minutes time delay)
Step 1: Press “ * * “ → 2 short beeps with Yellow light
Step 2: Press “159#“ → 2 short beeps with Yellow light
Step 3: Input “ Current Master Code #” → 2 short beeps with Yellow light
Step 4: Input ”Desired Delay Time (01-59) #” → 2 short beeps with Green light
01 = 1-minute Time Delay
59 = 59 minutes Time Delay
00 = turn off Time Delay Mode
If the Time Delay feature did not set successfully, the lock will beep 5 times with Red
light. Please repeat the steps
NOTE
1. During Time Delay period, Master code and user code will not be accepted. When
you press any key, the keypad will be no response.
2. Do NOT remove battery during time delay period. Within the last 30 seconds of
time delay period, the lock starts “Beep” continuously with Green light ashing.
3. Once the continuous beeps stop, the safe will be unlocked for 5 seconds.
LOCK OUT MODE
If the wrong codes are entered 4 times consecutively, the keypad will not accept any
code for 5 minutes. Lock starts beep with Yellow light continuously during the lockout
mode.
LOW BATTERY WARNING
If you encounter one of the situations below, please change your battery.
• When you input your code, a green light & red light will turn on for around 5
seconds. You will also hear 10 beeps. The safe will probably not unlock when you
get this response.
• When you input your code, a green light will turn on for around 1 second. The safe
will not open when you get this response.
• If your keypad has no response (no beeps; no light)
After the battery is changed, all registered pin codes will remain saved
TROUBLE SHOOTING
The lock has no response (no beeps)
- Make sure the battery wire in the keypad housing are not pinched and
are connected.
- Make sure you are NOT in Time Delay Mode.
- Replace the existing battery with new one.
The lock has continuous beeps
- Make sure the battery wire in the keypad housing are not pinched and
are connected.
- Make sure you are NOT in Time Delay Mode.
- The safe may be in lock out mode, please do NOT UNPLUG the battery and wait
for beep sound stop.
The lock is responding but cannot unlock
- Battery may be under voltage, replace new battery. Please refer to “LOW
BATTERY WARNING”
- Please check the safe is Dual User or Single User Open Mode. The safe is in Dual
User Mode, require 2 correct pin codes to open the safe. INCOMPLETED user
code entry, the light stays on Yellow. Please enter 2 completed user codes.
- The safe is in Time Delay Mode, the light stays on Yellow and Beep continuously for
30 seconds. Waiting for set delay time nish, the Green light ashing and safe
being unclocked for 5 seconds.
- Red light with 5 beeps this indicates wrong user code entry, please enter correct
user code.
10
11
CARE AND MAINTENANCE
- Keep liquids away from the control panel. Spills on the control panel will cause
damage and possibly electric shock.
- Secure safe in a proper area to prevent from falling and causing damage or injury.
- DO NOT disassemble the product. For all repairs, contact BARSKA
Customer Service.
- DO NOT use chemicals or cleaning agents to clean the safe.
MOUNTING INSTRUCTIONS
The safe may be mounted down to the oor. Be aware of the load bearing. Failure to
do so can result in personal injury and/or damage to property. Use appropriate tools
when performing work and always use eye protection.
Floor Mounting
- Use proper drill tools depending on the type of oor you are mounting the safe
(wood, tile, or concrete).
- Measure the location of the pre-set drill holes; mark their exact position onto
the oor.
- Drill the appropriate size holes for the anchors you are using.
- Carefully press the anchor into the holes at this time.
- Mount the safe by running screws from inside of the safe and securing to anchors;
ensure the safe is mounted securely
BC767
1 YEAR LIMITED WARRANTY
SAFE/LOCK BOX
BARSKA warrants this new safe/lock box to be free of defects in material and/ or
workmanship under normal use for a period of twelve (12) months from the date
product is purchased. This limited warranty is delimited to repair or replacement only.
This warranty does not cover damage caused by improper installation or maintenance.
BARSKA disclaims all liability for incidental or consequential damages resulting from
misuse, abuse, accident (such as dropping), re, ood, service or repairs other than
those performed by BARSKA, acts of nature, or arising out of any breach of this
warranty. Altering the product under any circumstances will automatically void the
warranty.
For service under this limited warranty, please have available the proof of purchase
and the purchase date and location as well as a detailed description of the problem.
This warranty is not transferable and only applies to the original purchaser with a proof
of purchase from BARSKA or from an authorized dealer. This warranty applies only to
products purchased within the United States, excluding Alaska, the Hawaiian Islands
and all U.S. territories in the Caribbean and the Pacic.
BARSKA will examine and go through troubleshooting procedures, product repair or
replacement of defective part(s) or units with new part(s) or provide a new unit, if
necessary, during the warranty period. Reasonable shipping/handling charges may
apply and are based on Barska sole discretion. Purchaser shall be required to prepay
Shipping/handling charges with a check or money order to BARSKA at time product
is returned. The Return Merchandise Authorization Number (RMA#) and shipping/
handling charge MUST be obtained from BARSKA in advance of return. BARSKA
shall not be liable for damages or loss occurring during shipping. Please visit via www.
barska.com or call 909.445.8168 to obtain the RMA#, Shipping/handling amount, and
for more information.
BARSKA reserves the right to modify or discontinue, without prior notice to the
purchaser, any model or style of the product. BARSKA will determine, at its sole
discretion, whether a product will be repaired or replaced. BARSKA reserves the
right to discontinue or change any feature of its products at any time. If an exact
replacement or product is not available, BARSKA reserves the right to provide a part
or product that matches as closely as possible.
LIMITATION OF REMEDIES
BARSKA disclaims any warranties, express or implied, whether of merchantability or
tness for a particular use, except as expressly set forth herein. The sole obligation of
BARSKA under this limited warranty shall be to repair or replace the covered product,
in accordance with the terms set forth herein. BARSKA expressly disclaims any lost
prots, general, special, indirect or consequential damages which may result from
breach of any warranty, or arising out of the use or inability to use any BARSKA
product. Any warranties which are implied and which cannot be disclaimed shall be
limited in duration to a term of one year from the date of original retail purchase.
Some states do not allow the exclusion or limitation of incidental or consequential
damages or limitation on how long an implied warranty lasts, so the above limitations
and exclusions may not apply to you.
BARSKA
855 Towne Center Drive, Pomona, CA 91767
Note: All information, feature, and specication displayed herein are based on the
data available at the time of publishing, thus they are subject to change without
notice. All product pictures displayed herein are for illustration purposes only. The
actual product may vary due to different circumstances
