HOTO
Flashlight Power
Safety Instructions
Please use the flashlight correctly as described in this manual.
The flashlight's light bulb is irreplaceable. When the light
bulb reaches the end of its service life, the entire flashlight
needs to be replaced.
Do not let children use the seat belt cutter and window
breaker.
Do not leave the flashlight in a car or in direct sunlight for a
long time in hot weather, as it may overheat and cause
burns.
WARNINGS
1
Do not charge outdoors on rainy days.
Precautions
This product can emit a strong light, please avoid directing
thelight at people's or animals' eyes and optical lenses.
Battery safety
Do not open or cut the battery.
Do not expose the battery to heat or flames. Keep the
battery away from direct sunlight.
Do not subject the battery to mechanical shock.
Charge the flashlight before using for the first time.
After long-term storage, the battery needs to be charged
and discharged several times for optimal performance.
The battery is at its best performance when used at room
temperature (20°C ± 5°C).
If the flashlight needs to be disposed of, the battery must
be removed.
The flashlight must be turned off before the battery is
removed.
Please recycle and dispose of the battery in a proper and
environmentally friendly manner.
In case of accidental battery leakage, do not get the
leaked liquid on your skin or eyes. In case of contact, rinse
with plenty of water and seek medical attention in time.
2
The flashlight emits a strong light. Avoid shining the light
directly into the eyes of people or animals, or into the
lenses of optical equipment.
To reduce the risk of injury, children should be supervised
by an adult when using the flashlight.
To reduce the risk of electric shock, do not place the
flashlight in water or any other liquids.
Do not place or store the flashlight anywhere near a
bathtub or sink.
When the high light (in the main light mode) or the strobe
mode are used for a long time, the surface of the flashlight
may start to warm up. This is normal. To reduce the risk of
burns, do not touch it if this happens.
The IP54 dust-tight and water-resistance fuction of the
flashlight will be ineffective without the tailtap.
Usage
3
Note: Illustrations of product, accessories, and user
interface in the user manual are for reference purposes only.
Actual product and functions may vary due to product
enhancements.
Charging
Please use a charger that meets the flashlight's
specifications.
If the flashlight has not been used for a long period of time
and the battery level indicator does not work properly
when charged again, continue charging for 30 minutes and
then check whether the battery level indicator works
normally.
If you use a charger that does not meet the flashlight's
specifications, any damage to the flashlight caused by this
will not be covered by the warranty, and it may lead to
other risks.
If the flashlight's battery reaches 45°C, the charging
protection function will be triggered and the charging will
be stopped. The recommended ambient temperature for
charging is room temperature.
4
Product Overview
Strike Bezel
1
1
Beam Adjuster
2
2
Type-C Charging Port
3
3
Mode Adjuster
4
4
Magnetic Base
5
5
Tailcap
6
6
Thank you for using the HOTO
Flashlight Power.
Read this manual carefully before use, and retain it for
future reference.
5
Battery Level
Indicator
7
7
On/Off Button
8
8
Side Light
9
9
Seat Belt Cutter
10
Window Breaker
11
10
11
6
Mode adjuster
Turn the mode adjuster to change between the two different
modes:
Main light mode
Side light mode
How to Use
Charging
Slide the beam adjuster upwards to expose the Type-C
charging port and insert the charging cable to charge.
When the flashlight is charging:
Main light: Only low light can be enabled.
Side light: You can cycle through low light, blinking red
light and blinking fog light.
Note: The flashlight comes with a Type-C charging cable.
The flashlight must be fully charged before its first use.
7
On/Off button
In main light mode:
Press and hold the on/off button for 0.5 seconds to turn on
the low light, then press again to cycle through: medium
light - high light - low light. Press and hold the on/off
button again for 0.5 seconds to turn the flashlight off.
In side light mode:
Press and hold the on/off button for 0.5 seconds to enable
the low light, then press again to cycle through: high light -
blinking red light - blinking fog light - low light. Press and
hold the on/off button again for 0.5 seconds to turn the
flashlight off.
Using the button:
Press and hold the on/off button for 0.5 seconds to turn
the flashlight on or off.
8
Beam adjuster
Slide the beam adjuster up and down to adjust between
spotlight and floodlight.
Strobe mode/SOS mode:
Press and hold the on/off button for 3 seconds at any time
to turn on the strobe mode, then press again to cycle
through: SOS mode - strobe mode. Press and hold the
on/off button again for 0.5 seconds to turn the flashlight
off.
Battery level indicator
If the battery level is above 20% while the flashlight is
turned on, the battery level indicator will remain white. If
the battery level is 20% or below, the battery level
indicator will remain red until the battery runs out and the
flashlight turns off.
The battery level indicator keeps breathing when charging
and will turn off when charging is completed. If charging
the flashlight when its battery is full, the battery level
indicator will turn off after breathing for 20 seconds.
9
The cutter and the seat belt should be at a 45° angle to
make cutting easier.
Seat belt cutter
Unscrew the tailcap first and
then use the seat belt cutter
according to the following
steps.
Step 1: Pull the seat belt across
your chest tight with your hand
to keep it straight.
Step 2: Hold the flashlight and
slot the taut seat belt into the
cutter.
Step 3: Keep the flashlight
level and quickly pull it
horizontally to cut the seat
belt.
10
!
11
Window breaker
Unscrew the tailcap, place the end of
the window breaker perpendicular to
the window and press hard. The
window breaker nail will pop out and
break the glass. Once you let go, the
window breaker nail will go back
inside the flashlight.
Magnetic base
The magnetic base can be attached
to any magnetic surface containing
iron, nickel, etc. The magnetic base's
sliding rail allows for 107° rotation of
the flashlight.
12
Issues
Possible Causes Solutions
Troubleshooting
Note: The flashlight's light bulb is irreplaceable. When the
light bulb reaches the end of its service life, the entire
flashlight needs to be replaced.
The battery level
indicator remains
red when you turn
on the flashlight.
The battery level
indicator does not
light up when
charging.
The flashlight
changes modes
automatically
when in use.
The window
breaker nail
doesn't come out.
The window breaker
is neither
perpendicular to the
surface nor being
pressed hard
enough.
Make sure the
window breaker is
perpendicular to the
surface and is
pressed down to the
end.
There are magnetic
interferences near
the mode adjuster.
Do not place the
flashlight near a
magnet or use in a
strong magnetic
environment.
1. The Type-C
charging cable isn't
plugged in or the
charging cable
provided isn't being
used.
2. The ambient
charging
temperature is
below 0°C or
above 45°C.
1. Use the charging
cable provided, and
make sure a 5 V
power adapter is
being used.
2. Charge at room
temperature.
Low battery power Charge the flashlight.
Specifications
Model: QWSDT004
Net Weight: Approx. 240 g
Input: 5 V 1.5 A
Item Dimensions: 188 × 40.5 × 36 mm
Charging Time: Approx. 180 min
Battery Rated Capacity: 3100 mAh
Battery Type: Lithium-ion Battery
IP Rating: IP54
Battery Rated Voltage: 3.6 V
13
Main Light Specifications
1000 lm
3 h
240 m 120 m 50 m
240 lm
5 h
High
Light
Medium
Light
Low
Light
50 lm
24 h
Brightness
Battery Life
Beam Distance
Side Light Specifications
30 lm
36 h
200 lm
5.5 h
Low
Light
High
Light
Blinking
Red Light
90 h
Blinking
Fog Light
90 h
Brightness
Battery Life
14
15
Regulatory Compliance
Information
Disposal and recycling information
All products bearing this symbol are waste electrical
and electronic equipment (WEEE as in directive
2012/19/EU) which should not be mixed with
unsorted household waste. Instead, you should
protect human health and the environment by handing over
your waste equipment to a designated collection point for
the recycling of waste electrical and electronic equipment,
appointed by the government or local authorities. Correct
disposal and recycling will help prevent potential negative
consequences to the environment and human health.
Please contact the installer or local authorities for more
information about the location as well as terms and
conditions of such collection points.
16
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
This supplier’s declaration of conformity is hereby for
We declare that the above mentioned device has been
tested and found in compliance with CFR 47 Part 15
Regulation.
Product: HOTO Flashlight Power
Model Number(s): QWSDT004
Brand/Trade: HOTO
Federal Communications Commission Supplier’s
Declaration of Conformity
17
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
18
Representative of Responsible Party for SDoC
Manufacturer: Shanghai HOTO Technology Co., Ltd.
Address: Building 45, No.50 Moganshan Road, Shanghai,
China
Company: HOTO (US) TECHNOLOGY CO LTD
Address: 919 North Market Street, Suite 950, Wilmington DE
19801
Country: U.S.A.
Customer Service(US): +1 855-577-2659
Mon-Fri 9:00am-5:00pm(CST)
