Model 24V-BZ100-LTE
Form No. SJ-24V-BZ100-LTE-880E-M
R
OPERATOR’S MANUAL
CORDLESS BUG ZAPPER
24V* IONMAX | USB-C + USB-A PORTS
Original instructions.
© 2023 Snow Joe, LLC. All rights reserved.
*DISCLAIMER: Initial no‑load voltage, when fully charged,
peaks at 24V; nominal voltage under typical load is 21.6V.
SAVE THESE INSTRUCTIONS
A Division of Snow Joe, LLC
1
TM
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
Always follow these safety guidelines. Failure to do so may result
in serious bodily injury or death.
General Safety
mWARNING! This appliance is not intended for use by
children or by unassisted, unsupervised persons whose
physical, sensory or mental capabilities prevent them from using
it safely. Children should be supervised to ensure that they do
not play with the appliance.
Before starting up your machine, please check it carefully
for any defects. If you find any, do not start up your machine.
Instead, contact your authorized Snow Joe
®
+ Sun Joe
®
dealer
or call the Snow Joe
®
+ Sun Joe
®
customer service center at
1-866-SNOWJOE (1-866-766-9563).
mWARNING! When using the power tool, basic safety
precautions should always be followed to reduce the risk of fire,
electric shock, and personal injury. These include
• Read all the instructions before using the tool.
• Do not look into the light, or expose the light to eyes. Eyes
may be damaged.
• To reduce the risk of injury, children must be supervised
when using the tool around them.
• To reduce the risk of electrical shock, do not put the bug
zapper or charger in water or other liquid. Do not place or
store them where they can fall or be pulled into a tub or sink.
• Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with another
battery pack.
• Use tool only with specifically designated battery packs. Use
of any other battery packs may create a risk of injury or fire.
• Remove battery pack from cordless bug zapper before
performing any routine maintenance or cleaning.
• Do not disassemble the bug zapper.
• Do not place bug zapper or battery pack near fire or heat.
They may explode. Do not incinerate the battery, even if it is
severely damaged or completely worn out. The battery may
explode in fire.
• Do not operate bug zapper or charger near flammable liquids
or in gaseous or explosive atmospheres. Internal sparks may
ignite fumes.
• Do not store in locations where the temperature is fewer than
50°F or more than 100°F. Do not store in outside sheds in
direct sunlight or in vehicles.
• Do not permit children to use bug zapper.
• Keep bug zapper dry, clean, and free from oil and grease.
Always use a clean cloth when cleaning. Never use brake
fluids, gasoline, petroleum-based products, or any strong
solvent to clean the bug zapper.
• Do not overreach while holding the bug zapper. Keep proper
footing and balance at all times. Proper footing and balance
enable better control of the bug zapper in unexpected
situations. Do not use on a ladder or unstable support.
mWARNING! Do not use this appliance without reading this
instruction manual.
Bug Zapper Use + Care
• Disconnect the product from the power supply when not in
use, before servicing, when changing bulbs, cleaning, and
similar actions.
• Do not insert foreign objects into this product.
• Store products indoors when not in use – out of reach of
children.
• Do not clean this product with a water spray or similar
method.
• Do not permit children to use this product. It is not a toy.
• If wrapped or in contact with fabrics, the product’s light
produces sufficient heat to melt some fabrics.
• This product is intended for household use only.
Safety Rules for Bug Zapper
• Always remove battery pack before storing the device.
• Under extreme usage or temperature conditions, battery
leakage may occur. If liquid comes in contact with your skin,
wash immediately with soap and water. If liquid gets in your
eyes, flush them with clean water for at least 10 minutes,
then seek immediate medical attention.
2
• Batteries can explode in the presence of a source
of ignition, such as a pilot light. To reduce the risk of
serious personal injury, never use any cordless product
in the presence of open flame. An exploded battery can
propel debris and chemicals. If exposed, flush with water
immediately.
• Do not crush, drop or damage battery pack. Do not use a
battery pack or charger that has been dropped or received
a sharp blow. A damaged battery is subject to explosion.
Properly dispose of a dropped or damaged battery
immediately. Failure to heed this warning can result in
serious personal injury.
• Save these instructions. Refer to them frequently and use
them to instruct others who may use this tool. If you loan
someone this tool, loan them these instructions also.
Battery & Charger Safety
Instructions
We pay a great deal of attention to the design of every battery
pack to ensure that we supply you with batteries that are safe,
durable and have a high energy density. The battery cells have
a wide range of safety devices. Each individual cell is initially
formatted and its electrical characteristic curves are recorded.
This data is then used exclusively to assemble the best possible
battery packs.
Despite all the safety precautions, caution must always be
exercised when handling batteries. The following points must
be obeyed at all times to ensure safe use. Safe use can only be
guaranteed if undamaged cells are used. Incorrect handling of
the battery packs can cause cell damage.
IMPORTANT! Analyses confirm that incorrect use and poor care
of high-performance batteries are the main factors responsible
for product damage and/or personal injury.
mWARNING! To reduce the risk of injury, use only official
24V IONMAX designated chargers and battery packs. The use
of other batteries or chargers poses a risk of fire, personal injury
and damage.
mWARNING! Do not use a battery pack or product that has
been damaged or modified. Damaged or modified batteries may
exhibit unpredictable behavior resulting in fire, explosion or risk
of injury.
Do not modify or attempt to repair the product or the battery
pack except as indicated in the instructions for use and care.
Do not wire a battery pack to a power supply or car cigarette
lighter, as such misuse will permanently disable or damage the
battery pack.
Have your battery pack serviced by a qualified repair person
using only identical replacement parts. This will ensure that the
safety of the battery pack is maintained.
mWARNING! To reduce the risk of electric shock,
always unplug the charger before performing any cleaning or
maintenance. Do not allow water to flow into the charger. Use a
Ground Fault Circuit Interrupter (GFCI) to reduce shock hazards.
• Remove battery – Remove the battery pack from the tool
when not in use, before servicing, or before performing any
other maintenance task. Never leave the tool unattended
while switched on. In the event of an accident or breakdown,
switch off the tool immediately.
• Avoid dangerous environments – Do not charge the battery
packs in rain, snow or in damp or wet locations. Do not use
the battery pack or charger in the presence of explosive
atmospheres (gaseous fumes, dust or flammable materials)
because sparks may be generated when inserting or
removing the battery packs, which could lead to a fire.
• NOTE: The safe temperature range for the batteries are 41°F
(5°C) to 105°F (40.5°C). Do not charge the batteries outside
in freezing weather; charge them at room temperature.
• Charge in a well-ventilated area – Do not block the charger
vents. Keep them clear to allow for proper ventilation. Do not
allow smoking or open flames near a charging battery pack.
Vented gases may explode.
• Maintain charger cord – When unplugging the charger, pull
the plug, not the cord from the receptacle to reduce the risk
of damage to the power cord. Never carry the charger by its
cord. Keep the cord away from heat, oil and sharp edges.
Make sure the cord will not be stepped on, tripped over or
subjected to damage or stress when the charger is in use.
Do not use a charger with a damaged cord or plug. Replace
a damaged charger immediately.
• Do not use an extension cord unless it is absolutely
necessary – Using the wrong, damaged or improperly wired
extension cord poses a risk of fire and electric shock. If
an extension cord must be used, plug the charger into a
properly wired 16 gauge or larger extension cord with the
female plug matching the male plug on the charger. Make
sure that the extension cord is in good electrical condition.
• Do not expose the machine or battery packs to fire –
Exposure to fire or temperatures above 265°F (130°C) may
cause the battery packs to explode, causing personal injury
or damage. Toxic fumes and materials are created when
battery packs are ignited.
• Do not crush, drop or damage battery packs – Do not
use the battery packs or charger if they have sustained a
sharp blow, been dropped from a height of more than 3 feet
(1 meter), run over or have been damaged in any way. Even
if the housing of a battery pack appears to be undamaged,
the battery cells inside the battery may have suffered serious
damage. In such instances, please read the waste disposal
information for proper battery disposal.
3
• Do not disassemble – Incorrect reassembly may pose
a serious risk of electric shock, fire or exposure to toxic
battery chemicals. If the battery or charger is damaged,
contact an authorized Snow Joe
®
+ Sun Joe
®
dealer or
call the Snow Joe
®
+ Sun Joe
®
customer service center at
1-866-SNOWJOE (1-866-766-9563) for assistance.
• Battery chemicals cause serious burns – Never let a
damaged battery pack contact the skin, eyes or mouth. If
damaged, battery chemicals will react violently with air. Use
rubber or neoprene gloves to safely dispose of the battery.
If skin is exposed to battery chemicals, wash the affected
area with soap and water. If eyes are exposed to battery
chemicals, immediately flush with water for 20 minutes and
seek medical attention. Remove and dispose of contaminated
clothing.
• Risk of short circuit – A battery pack will short circuit if
a metal object makes a connection between the positive
and negative contacts on the battery pack. Do not place a
battery pack near anything that may cause a short circuit,
such as paperclips, coins, keys, screws, nails and other
metallic objects. A short-circuited battery pack poses a risk
of fire and severe personal injury.
• Store your battery packs and charger in a cool, dry
place – Ideally, store the battery packs at 59°F (15°C) and
charged to at least 40%. Do not store the battery packs or
charger where temperatures may exceed 105°F (40.5°C),
such as in direct sunlight or inside a vehicle, or where
temperatures may drop below 41°F (5°C).
• NOTE: Prevent the battery packs from freezing. Battery
packs that were stored below 32°F (0°C) for more than 60
minutes must be discarded.
• Charge before use – The battery pack supplied with your
machine is only partially charged. The battery pack must be
fully charged before using the bug zapper for the first time.
• Battery Aging – Lithium-ion batteries are subject to a natural
aging process. A battery pack must be replaced at the
latest when its capacity falls to just 80% of its capacity when
new. Weakened cells in an aged battery pack are no longer
capable of meeting the high power requirements needed for
the proper operation of your machine, and therefore pose a
safety risk.
• Do not exhaustively discharge battery packs – A complete
discharge will damage the battery cells. The most common
cause of exhaustive discharge is lengthy storage. Stop
working as soon as the performance of a battery falls
noticeably or the electronic protection system triggers. For
optimum battery performance, charge the battery packs
frequently. Place the battery packs in storage only after they
have been fully charged.
• Do not overload battery packs – Protect the bug zapper
and battery from overloading. Overloads will quickly result
in overheating and cell damage inside the battery housing
even if it is not apparent externally. For safety reasons, the
integrated protective cutoff will activate to switch off the
equipment. After regular use, allow the battery packs to cool
to room temperature before recharging them.
• IMPORTANT! Do not attempt to turn on the machine if the
protective cutoff has been activated. This may damage the
battery packs.
• Outlet voltage – Please check the data marked on the
rating label of the battery charger. Be sure that the voltage
of the power supply matches that marked on the rating label.
Never connect it to a different mains voltage.
• Charger use – Do not use the battery charger to charge
other types of battery packs or tools.
• Do not overcharge battery packs – Do not exceed the
maximum charging times. Frequently overcharging the
battery packs will result in cell damage. Do not leave battery
connected to the charger for days on end.
• Battery pack abnormalities – Do not use batteries that
have suffered swelling or deformation or those that exhibit
other atypical symptoms (gassing, hissing, cracking, etc.).
• Electrostatic discharge – When handling batteries, be wary
of electrostatic charge. Electrostatic discharges can damage
the electronic protection system and the battery cells. To
avoid electrostatic discharges, never touch the battery
terminals.
4
Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all
instructions on the product before attempting to assemble and operate.
Symbols Descriptions Symbols Descriptions
READ THE OPERATOR’S
MANUAL(S) – Read, understand,
and follow all instructions in the
user manual(s) before attempting to
assemble and operate.
SAFETY ALERT – Indicates a
precaution, a warning, or a danger.
Do not expose to rain or use in damp
locations.
To reduce the risk of electrocution
or electric shock, keep away from
water.
V
Voltage Type or a characteristic of current.
5
Know Your 24V Max* Cordless Bug Zapper
Read the owner’s manual and safety instructions carefully before operating the bug zapper. Compare the illustration below to the
product in order to become familiar with the location of the various controls and adjustments. Save this manual for future reference.
Technical Data
Electric Grid .........................................................................2500 V D.C.
UV Black Light ............................................................................... 10 W
Battery Voltage Max* ............................................................. 24 V D.C.
Battery Capacity ...........................................................................2.0 Ah
Charger Input .......................... 100 – 240V AC | 50/60 Hz | 0.4 A
Charger Output ...................................................... 26V DC | 450 mA
Charge Time Max ..................................................................... 5 hours
LED worklight lumens .................. 33 (low), 45 (medium), 65 (high)
Charging Ports ............................................ USB-A + USB-C (5V 2A)
Net weight .................................................................... 2.3 lbs (1.04 kg)
1
2
8
10
11
12 13 14 15 16 17
18
9
4
3
5
6
7
* DISCLAIMER: Initial no‑load voltage, when fully charged, peaks at 24V; nominal voltage under typical load is 21.6V.
1. Handle
2. Hanging hook
3. LED worklight
4. Protective panel
5. Collection tray
6. Touch screen display
7. Battery compartment
8. USB-C port
9. USB-A port
10. Latch
11. Cleaning brush
12. 24V* IONMAX lithium-ion battery (24VBAT-LTE)
featuring exclusive EcoSharp
®
technology
13. Charge socket
14. Push lock button (2)
15. Push button for battery indicator
16. Battery indicator
17. 24V* IONMAX lithium-ion charger
(XZ2600-0450)
18. Charger plug
6
Unpacking
Carton Contents
• Bug zapper
• Cleaning brush
• Battery compartment cover
• 24V* IONMAX lithium-ion battery
• 24V* IONMAX lithium-ion battery charger
• Manual with registration card
1. Carefully remove the cordless bug zapper and check to see
that all of the above items are supplied.
2. Inspect the product carefully to make sure no breakage or
damage occurred during shipping. If you find damaged or
missing parts, DO NOT return the unit to the store. Instead,
please call the Snow Joe
®
+ Sun Joe
®
customer service
center at 1-866-SNOWJOE (1-866-766-9563).
NOTE: Do not discard the shipping carton and packaging
materials until you are ready to use your new cordless bug
zapper. The packaging is made of recyclable materials.
Properly dispose of these materials in accordance with local
regulations.
IMPORTANT! The equipment and packaging materials are not
toys. Do not let children play with plastic bags, foils or small parts.
These items can be swallowed and pose a suffocation risk!
Battery Pack Operation
The equipment is powered by a lithium-ion battery. The battery
pack is completely sealed and maintenance free.
Battery Charge Level Indicator
The battery pack is equipped with a push button for checking
the charge level. Simply press the push button to read off the
battery charge level from the LEDs of the battery indicator:
Lights Light Indicators
Charge level button
The battery is at 30% capacity
The battery is at 60% capacity
The battery is fully charged
NOTE: If the battery indicator button does not appear to be
working, charge the battery.
NOTE: Immediately after using the battery pack, the battery
indicator button may display a lower charge than it will if
checked a few minutes later. The battery cells “recover” some of
their charge after resting.
Charger Operation
mWARNING! Only charge Sun Joe
®
24V lithium-ion battery
pack with compatible Sun Joe
®
24V lithium-ion chargers. Other
types of chargers may cause personal injury and damage.
To reduce the risk of electric shock, do not allow water to enter
into the charger.
Charging the Battery
1. Push the push lock buttons on either side of the battery
pack to pull it out from the battery compartment (Fig. 1)
2. Check that the mains voltage is the same as that marked on
the rating plate of the battery charger. Then plug the charger
into an appropriate AC power outlet. Connect the charger
plug into the charging socket of the battery to start charging
(Fig. 2).
Fig. 1
Push lock button
Latch
Battery
compartment
Battery
compartment
cover
Fig. 2
Battery
indicators
7
3. The battery will take approximately 5 hours to charge. The
battery indicator LEDs will cycle on one by one during the
charging process. Unplug the charger immediately when all
3 LEDs are illuminated.
mCAUTION! FIRE HAZARD. When disconnecting the
charger from the battery, be sure to unplug the charger from the
outlet first, then disconnect the battery from the charger.
mWARNING! This charger does not automatically turn off
when the battery is fully charged. Please take care not to leave
the battery plugged into the charger. Switch off or unplug the
charger at the mains when charging is complete.
4. Timely recharging of the battery will help prolong the
battery’s life. Recharge the battery pack when you notice a
drop in the equipment’s power.
IMPORTANT! Never allow the battery pack to become fully
discharged as this will cause irreversible damage to the battery.
Assembly
mWARNING! Do not use this product if it is not completely
assembled or if any parts appear to be missing or damaged.
Use of a product that is not properly and completely assembled
or with damaged or missing parts could result in serious
personal injury.
mWARNING! Do not attempt to modify this product or
create accessories or attachments not recommended for use
with this product. Any such alteration or modification is misuse
and could result in a hazardous condition leading to possible
serious personal injury.
If any parts are damaged or missing, please call the Snow Joe
®
+ Sun Joe
®
customer service center at 1-866-SNOWJOE
(1-866-766-9563) for assistance.
Operation
mWARNING! Do not allow familiarity with tools to make
you careless. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
mWARNING! Do not use any attachments or accessories
not recommended by the manufacturer of this tool. The use of
attachments or accessories not recommended can result in
serious personal injury.
mWARNING! Keep the bug zapper away from combustible
materials. If wrapped or in contact with fabrics, the light may
produce sufficient heat to melt some fabrics.
mWARNING! To reduce the risk of fire, remove insects and
empty bug tray frequently.
mWARNING! Do not insert foreign objects into this product.
Doing so could damage the product and/or result in an electric
shock.
mWARNING! Battery tools are always in operating
condition. Therefore, unit should always be OFF with the
battery pack removed when not in use. Failure to follow these
instructions could result in serious personal injury.
mWARNING! Always remove battery pack from your
product when you are assembling parts, making adjustments,
cleaning, or when not in use. Removing battery pack will prevent
accidental starting that could cause serious personal injury.
1. Remove the battery compartment cover, then insert the
battery pack into the battery compartment until the push lock
buttons click into place (Fig. 3).
2. Close the battery compartment cover. Make sure the latches
on each side of the cover snap into place and the battery
pack is secured before beginning operation.
mWARNING! Battery products are always in operating
condition. Therefore, remove the battery pack when the product
is not in use or when carrying at your side.
UV Light/LED
The bug zapper has two settings: UV Light and LED (Fig. 4).
• UV Light: touch the UV light switch to cycle between 2
hours, 4 hours, 6 hours, and off as indicated by the LEDs
below the UV light switch.
• LED: gently touch the LED switch to switch on low light;
touch twice: medium light
touch three times: high light
touch four times: switch off the LED
Fig. 3
Battery
compartment
Latch
Battery
compartment
cover
Push lock button
8
OPERATING TIPS
• For best results, hang the product 6 to 7 ft. above the
ground.
• Dead insects and debris will accumulate in the bug tray.
Remove insects and empty bug tray frequently. To clean the
tray, open the tray from two sides and dump the waste into
a trash receptacle. If necessary, use a brush to clean the
inside of the tray.
• NOTE: Be sure to wash your hands thoroughly with soap
and water after handling the bug tray.
• Periodically, remove the battery pack and use a soft brush
or forced air to remove dead insects or debris from the
product.
• Remove the battery pack and store product indoors dur-
ing severe weather. This product can withstand moderate
rainfall, but it should not be left outdoors during severe
weather events.
1. Lift the hanging hook and rotate to the desired position for
hanging (Fig. 5).
Fig. 4
Time: 2 hrs,
4 hrs, 6 hrs
Low,
medium,
high
LED light
switch
UV light switch
Fig. 5
Hanging
hook
NOTE: Do not attach anything other than the battery pack
to the bug zapper when it is hanging from the hook. Do not
stand under the hanging bug zapper to prevent hazard from
falling.
2. Be careful not to hang the bug zapper in a position that
prevents normal operation of the bug zapper.
3. When not hanging, pull out the handle and use it as a night
light (Fig. 6).
Using the USB-A + USB-C Ports
Both USB charging ports provide 5V DC charging power for
your mobile phone, MP3 player and other USB devices, and up
to 2 amps total.
mCAUTION! Attempting to charge devices rated more than
2 amps, such as a tablet, could damage the USB charging ports
and/or the devices.
1. Open the rubber USB ports cover protector (Fig. 7).
2. Connect one end of the USB cable (not included) to your
USB device.
Fig. 6
Handle
Fig. 7
USB-C
USB-A
9
3. Connect the other end of the USB cable (not included) to
the USB charging port. Then press the UV light or LED light
switch to start charging the device (Fig. 8).
4. After charging, remove the USB cable, then put the rubber
USB ports cover protector back into place.
Cleaning the Collection Tray
1. Open the bug collection tray to 60º, and then clean the tray
with the cleaning brush. Avoid touching insects by hand.
2. Close the collection tray back into the housing (Fig. 9).
Fig. 8
USB-C
USB-A
60˚
Fig. 9
Bug collection tray
Maintenance
Please contact an authorized Snow Joe
®
+ Sun Joe
®
dealer
or call the Snow Joe
®
+ Sun Joe
®
customer service center
at 1-866-SNOWJOE (1-866-766-9563) for all maintenance
operations not detailed in this manual. Any operation
performed in an unauthorized service center or by unqualified
personnel will completely invalidate the warranty.
mWARNING! To avoid serious personal injury, always
remove the battery pack from the product when cleaning or
performing any maintenance.
mWARNING! When servicing, use only identical
replacement parts. Use of any other parts could create a hazard
or cause product damage.
NOTE: Periodically inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps, etc.
Tighten securely all fasteners and caps and do not operate
this product until all missing or damaged parts are replaced.
Please contact customer service or a qualified service center for
assistance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics
are susceptible to damage from various types of commercial
solvents and may be damaged by their use. Use clean cloths to
remove dirt, dust, oil, grease, etc.
mWARNING! Do not at any time let brake fluids, gasoline,
penetrating oils, etc., come in contact with plastic parts.
Chemicals can damage, weaken, or destroy plastic, which may
result in serious personal injury.
BULB REPLACEMENT
1. Unscrew the two M5 screws from the bug zapper top and
remove the upper cover of bug zapper.
2. Take out the old UV light upward; insert the new UV light
downward.
3. Reassemble the upper cover with M5 screws (Fig. 10).
Fig. 10
UV light
M5 screws
10
STORING THE BUG ZAPPER
Store indoors in a dry, locked-up place, out of the reach of
children, with the battery pack removed. Keep away from
corrosive agents such as garden chemicals and deicing salts.
Battery Caution + Disposal
Always dispose of your battery pack according to federal, state,
and local regulations. Contact a recycling agency in your area
for recycling locations.
mCAUTION! Even discharged battery packs contain
some energy. Before disposing, use electrical tape to cover the
terminals to prevent the battery pack from shorting, which could
cause a fire or explosion.
mWARNING! To reduce the risk of injury or explosion,
never burn or incinerate a battery pack even if it is damaged,
dead, or completely discharged. When burned, toxic fumes and
materials are emitted into the surrounding environment.
• Batteries vary according to device. Consult your manual for
specific information.
• Install only new batteries of the same type in your product
(where applicable).
• Failure to insert batteries in the correct polarity, as indicated
in the battery compartment or manual, may shorten the life of
the batteries or cause batteries to leak.
• Do not mix old and new batteries.
• Do not mix Alkaline, Standard (Carbon-Zinc), or
Rechargeable (Nickel Cadmium, Nickel Metal Hydride, or
Lithium-Ion) batteries.
• Do not dispose of batteries in fire.
• Batteries should be recycled or disposed of as per state and
local guidelines.
Recycling + Disposal
The product comes in a package that protects it against damage
during shipping. Keep the package until you are sure that
all parts have been delivered and the product is functioning
properly. Recycle the package afterwards or keep it for long-
term storage.
WEEE symbol. Waste electrical products should not
be disposed of with household waste. Please recycle
where facilities exist. Check with your local authority
or local store for recycling regulations.
Service + Support
If your Sun Joe
®
24V-BZ100-LTE cordless bug zapper requires
service or maintenance, please call 1-866-SNOWJOE
(1-866-766-9563) for assistance.
Model + Serial Numbers
When contacting the company, reordering parts, or arranging
service from an authorized dealer, you will need to provide the
model and serial numbers, which can be found on the decal
located on the housing of the unit. Copy these numbers into the
space provided below.
XZ2600-0450
Federal Communications Commission
(FCC)
mWARNING! Any changes or modifications to this unit not
expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Class B Device:
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in
a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment to an outlet on a circuit different
than the one the receiver is connected to.
• Consult the dealer or an experienced radio/TV technician
for help
Record the following numbers from the housing or handle of
your new product:
Model #:
Serial #:
24V-BZ100-LTE
11
Optional Accessories
m
WARNING! Only use authorized Snow Joe
®
+ Sun Joe
®
replacement parts and accessories. NEVER use replacement parts
or accessories that are not intended for use with this bug zapper. Contact Snow Joe
®
+ Sun Joe
®
if you are unsure whether it is
safe to use a particular replacement part or accessory with your bug zapper. The use of any other attachment or accessory can be
dangerous and could cause injury or mechanical damage.
Accessories Item Model
24V* IONMAX 2.0 Ah Lithium-Ion Battery 24VBAT-LTE
24V* IONMAX 2.5 Ah Lithium-Ion Battery 24VBAT-LT
24V* IONMAX 4.0 Ah Lithium-Ion Battery 24VBAT
24V* IONMAX 5.0 Ah Lithium-Ion Battery 24VBAT-XR
24V* IONMAX Lithium-Ion Battery
Quick Charger
24VCHRG-QC
24V* IONMAX Lithium-Ion Battery
Dual Port Charger
24VCHRG-DPC
Visit sunjoe.com for more options
NOTE: Accessories are subject to change without any obligation on the part of Snow Joe
®
+ Sun Joe
®
. Accessories can be ordered online at
sunjoe.com or via phone by contacting the Snow Joe
®
+ Sun Joe
®
customer service center at 1-866-SNOWJOE (1-866-766-9563).
1
2
3
4
5
6
R5_05112023
SNOW JOE
®
+ SUN JOE
®
CUSTOMER PROMISE
OUR WARRANTY:
Snow Joe warrants new, genuine, powered and non-powered Products to be free from defects in material or workmanship when used for
ordinary household use for a period of two years from the date of delivery of the Product to the original, end-user purchaser when purchased
from Snow Joe or from one of Snow Joe’s authorized sellers with proof of purchase. Because Snow Joe is unable to control the quality
of its Products sold by unauthorized sellers, unless otherwise prohibited by law, this Warranty does not cover Products purchased from
unauthorized sellers. If your Product does not work or there’s an issue with a specific part that is covered by the terms of this Warranty,
Snow Joe will elect to either (1) send you a free replacement part, (2) replace the Product with a new or comparable product at no charge,
or (3) repair the Product. How cool is that!
This Warranty gives you specific legal rights, and you may also have other rights which vary from State to State.
PRODUCT REGISTRATION:
Snow Joe strongly encourages you to register your Product. You can register online at snowjoe.com/register, or by printing and
mailing in a registration card available online from our website, or by calling our Customer Service Department at 1-866-SNOWJOE
(1-866-766-9563), or by e-mailing us at [email protected]. Failure to register your Product will not diminish your warranty rights. However,
registering your Product will allow Snow Joe to better serve you with any of your customer service needs.
WHO CAN SEEK LIMITED WARRANTY COVERAGE:
This Warranty is extended by Snow Joe to the original purchaser and original owner of the Product.
WHAT IS NOT COVERED?
This Warranty does not apply if the Product has been used commercially or for non-household or rental applications. This Warranty also
does not apply if the Product was purchased from an unauthorized seller. This Warranty also does not cover cosmetic changes that do
not affect performance. Wearing parts like belts, augers, chains and tines are not covered under this Warranty, and can be purchased at
snowjoe.com/support or by calling 1-866-SNOWJOE (1-866-766-9563).
Keep your warranty intact. Only use CERTIFIED AUTHENTIC Snow Joe
®
, Sun Joe
®
, Aqua Joe
®
+ Auto Joe
®
replacement parts +
accessories. Use of any other parts + accessories will void the warranty. Genuine parts + accessories can be found and purchased online at
snowjoe.com/support by entering the model number of your product.
ABOVE ALL ELSE, Snow Joe, LLC (“Snow Joe”) is dedicated to you, our customer. We strive to make your experience as pleasant as
possible. Unfortunately, there are times when a Snow Joe
®
, Sun Joe
®
, Aqua Joe
®
, or Auto Joe
®
product (“Product”) does not work or breaks
under normal operating conditions. We think it’s important that you know what you can expect from us. That’s why we have a Limited
Warranty (“Warranty”) for our Products.
TM
sunjoe.com
