MICHIGAN GDTSRDMC3C0A 2400W Electric Garden Mulcher User Manual

User Manual

[Revision 2.0]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY

VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may vary in appearance,

assembly, inclusions, specifications, description, and packaging.

Garden Shred 300 Electric Shredder

E&OE © Michigan 2

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases, or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

•

Work areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

•

Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol, or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory, or

mental capabilities.

General Fuel Safety

•

Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

• Always refuel in well ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start, or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

•

Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors, and

vents.

General Equipment Use and Care

•

Keep packaging away from children and

pets, potential risk of suffocation or

choking.

• The equipment is designed for domestic

use only.

• Handle the equipment safely and carefully.

• Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage, or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

• Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

• Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

• Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases, or liquids etc.

• The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

• Do not clean equipment with solvents,

flammable liquids, or harsh abrasives.

• For specific equipment safety use and care,

see Equipment Safety.

MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN

Garden Shred 300 Electric Shredder

E&OE © Michigan 3

General Electrical Safety

•

Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Always use a Residual Current Device

(RCD) (GFCI) / Earth Leakage Circuit

Breaker / Safety Switch when operating this

item (electrical items only).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

•

Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

•

The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories, or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service-related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

Child Choking Hazard!

• W

ARNING: CHOKING HAZARD - CHILDREN UNDER 8 YRS. CAN CHOKE OR SUFFOCATE ON SMALL PARTS. ADULT

SUPERVISION REQUIRED.

• Carefully inspect anything a baby or child could gain access to, including this product & packaging.

• Dangers include anything of a size that could become stuck or lodged in a baby or child's airway.

• Dangers include things like raw, hard fruit and vegetable pieces, large pieces of meat, bones or sausage skins, popcorn, nuts,

hard lollies and corn chips, small magnets and batteries, coins, beads, marbles and small uninflated balloons, broken toys and smaller toys,

buttons, keys, and coins. But there are also many more.

• Pay particular attention to accessories, nuts, bolts, screws, washers, caps, covers, loose parts, parts that could be removed or break off, pieces

of packaging, staples, tape etc.

• In the case of any doubt, secure the item of concern in an appropriate manner, or completely remove the possibility of access by a baby or child.

IMPORTANT!

• R

EAD CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack

of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the

hazards involved.

• Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Keep children and

pets at a safe distance away from the device.

• Local regulations or bylaws may determine the minimum age for using the shredder.

Training

•

Read the instructions carefully. Be familiar with the controls and the correct use of the machine.

• Never allow children or people unfamiliar with these instructions to use the machine. Local regulations can restrict the age of the operator.

• Keep in mind, that the operator or user is responsible for accidents or hazards occurring to other people or their property.

Hazardous Components

•

Be aware that the equipment may include hazardous components, such as blades, hot surfaces and moving parts.

• Moving blades can cause serious injury and even death if used improperly or without sufficient PPE.

• Do not use this equipment on uneven surfaces and always maintain good balance when using this equipment. Failure to do so may cause

serious injury.

• Maintain a secure grip of the trigger assembly at all times.

Preparation

•

Obtain ear protection and safety glasses. Wear them at all times while operating the machine.

• While operating the machine always wear substantial footwear and long trousers. Do not operate the machine when barefoot or wearing open

sandals. Avoid wearing clothing that is loose fitting or that has hanging cords or ties.

• Operate the machine in a recommended position and only on a firm, level surface.

• Do not operate the machine on a paved or gravel surface where ejected material could cause injury.

• Before using, always visually inspect to see, that the shredding means, shredding means bolts and other fasteners are secure, the housing is

undamaged, and that guards and screens are in place. Replace worn or damaged components in sets to preserve balance. Replace damaged or

unreadable labels.

MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN

Garden Shred 300 Electric Shredder

E&OE © Michigan 4

• Before use check the supply and extension cord for signs of damage or aging. If the cord becomes damaged during use, disconnect the cord

from the supply immediately. DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUPPLY. Do not use the machine if the cord is

damaged or worn.

• Never operate the machine while people, especially children, or pets are nearby.

Operation

•

Before starting the machine, make certain that the feeding chamber is empty.

• Keep your face and body away from the feed intake opening.

• Do not allow hands or any other part of the body or clothing inside the feeding chamber, discharge chute, or near any moving part.

• Keep proper balance and footing at all times. Do not overreach. Never stand at a higher level than the base of the machine when feeding material

into it.

• Always stand clear of the discharge zone when operating this machine.

• When feeding material into the machine be extremely careful that pieces of metal, rocks, bottles, cans or other foreign objects are not included.

• If the cutting mechanism strikes any foreign objects or if the machine should start making any unusual noise or vibration, immediately shut off the

power source and allow the machine to stop. Disconnect the machine from the supply and take the following steps before restarting and

operating the machine:

• inspect for damage.

• replace or repair any damaged parts.

• check for and tighten any loose parts.

• Do not allow processed material to build up in the discharge zone; this may prevent proper discharge and can result in kickback of material

through the feed intake opening.

• If the machine becomes clogged, shutoff the power source and disconnect the machine from supply before cleaning debris.

• Never operate the machine with defective guards or shields, or without

Maintenance and Storage

•

When the machine is stopped for servicing, inspection, or storage, or to change an accessory, shut off the power source, disconnect the machine

from the supply and make sure that all moving parts are come to a complete stop. Allow the machine to cool before making any inspections,

adjustments, etc. Maintain the machine with care and keep it clean.

• Store the machine in a dry place out of the reach of children.

• Always allow the machine to cool before storing.

• When servicing the shredding means be aware that, even though the power source is switched off due to the interlock feature of the guard, the

shredding means can still be moved.

• Replace worn or damaged parts for safety. Use only genuine replacement parts and accessorises.

• Never attempt to override the interlocked feature of the guard.

• Additional safety instructions for units with bagging attachments.

• Switch-off the machine before attaching or removing the bag.

Recommendation

•

The machine should be supplied via a residual current device (RCD) with a tripping current of not more than 30 mA.

Service

•

Have your garden power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the

garden power tool is maintained.

• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent in order to avoid a hazard.

• If the carbon brushes need to be replaced, have this done by a qualified repair person (always replace the two brushes at the same time).

Vibration and Noise Reduction

To reduce the impact of noise and vibration emission, limit the operating time, use low vibration and low-noise operating modes, and wear personal

pr

otective equipment. Take the following points into account to minimise the vibration and noise exposure risks:

• Only use the product as intended by its design and these instructions.

• Ensure that the product is in good condition and well maintained.

• Use correct attachments for the product and ensure they are in good condition.

• Keep tight grip on the handles/grip surface.

• Maintain this product in accordance with these instructions and keep it well lubricated (where appropriate).

• Plan your work schedule to spread any high vibration tool use across a longer period of time.

Emergency

Familiarise yourself with the use of this product by means of this instruction manual. Memorise the safety directions and follow them scrupulously.

T

his will help to prevent risks and hazards.

• Always be alert when using this product, so that you can recognise and handle risks early. Fast intervention can prevent serious injury and

damage to property.

• Switch off and disconnect from the power supply if there are malfunctions. Have the product checked by a qualified professional and repaired, if

necessary, before you operate it again.

MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN

Garden Shred 300 Electric Shredder

E&OE © Michigan 5

Residual Risks

Even if you are operating this product in accordance with all the safety requirements, potential risks of injury and damage remain. The following

danger

s can arise in connection with the structure and design of this product:

• Health defects resulting from vibration emission if the product is being used over long periods of time or not adequately managed and properly

maintained.

• Injuries and damage to property due to broken cutting attachments or the sudden impact of hidden objects during use.

• Danger of injury and property damage caused by flying objects.

• Prolonged use of this product exposes the operator to vibrations and may produce ‘white finger’ disease. In order to reduce the risk, please wear

gloves and keep your hands warm. If any of the ‘white finger’ symptoms appear, seek medical advice immediately. ‘White finger’ symptoms

include numbness, loss of feeling, tingling, pricking, pain, loss of strength, changes in skin colour or condition.

These symptoms normally appear in the fingers, hands, or wrists. The risk increases at low temperatures.

Additional Safety Instructions for Electric Shredder

•

Do not use appliance for a use other than the intended use.

• Maintain labels and nameplates on the appliance. These carry important safety information. If unreadable or missing, contact the point of

purchase for a replacement.

• The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may

occur.

• It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by

the operator.

• Before starting, ensure that the feed inlet is empty.

• Always wear ear and eye protection and wear gloves during operation.

• Longer material standing out from the shredder could lash out when being pulled in by the blades. Keep a safe distance.

• Ensure the ventilation slots are not covered.

• Always wear substantial footwear and long trousers while operating the machine.

Advice

•

Do not overreach. Keep the balance at all times, to always be sure of the footing on slopes.

• Walk, never run.

• Do not connect a damaged cord to the supply or touch a damaged cord before it is disconnected from the supply for the reason that damaged

cords can lead to contact with live parts.

• Keep extension cords away from moving hazardous parts to avoid damages to the cords which can lead to contact with live parts.

• WARNING! DO NOT TOUCH MOVING HAZARDOUS PARTS BEFORE THE MACHINE IS DISCONNECTED FROM THE MAINS AND THE

MOVING HAZARDOUS PARTS HAVE COME TO A COMPLETE STOP. NEVER OPERATE THE MACHINE WITH DEFECTIVE GUARDS OR

SHIELDS, OR WITHOUT SAFETY DEVICES, OR IF THE CORD IS DAMAGED OR WORN.

Recommendations

•

Avoid using the machine in bad weather conditions especially when there is a risk of lightning.

Maintenance

•

Before and after each use, check the product and accessories (or attachments) for wear and damage. If required, exchange them for new ones

as described in this instruction manual. Observe the technical requirements.

• Be aware of the danger of moving hazardous parts.

• WARNING: FOR YOUR SAFETY, IT IS REQUIRED THAT THE PLUG ATTACHED TO THIS PRODUCT IS ALWAYS CONNECTED TO AN

EXTENSION CORD! THE EXTENSION CORD MUST BE SUITABLE FOR OUTDOOR USE WITH SOCKETS PROTECTED AGAINST WATER

SPLASHING! ENSURE THE EXTENSION CORD IS OF THE PROPER SIZE AND TYPE FOR YOUR PRODUCT (≥ 1.5MM

2

), WHICH SHALL

NOT LESS RUBBER INSULATED, ORDINARY POLYCHLOROPRENE SHEATHED FLEXIBLE CORD (CODE DESIGNATION (H05VV-F)

AND LENGTH SHOULD MORE THAN 10M.

Intended Use

•

The product is intended for reducing biodegradable, garden organic waste materials to smaller pieces, such as leaves, small branches, and

grass, and used in a stationary position by an operator standing on the ground.

• This product is not intended for shredding pieces of metal, rocks, bottles, cans, etc. or soft waste such as kitchen rubbish.

• It must not be used for any purposes other than those described.

MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN

Garden Shred 300 Electric Shredder

E&OE © Michigan 6

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases, or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases, or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing, and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN

Garden Shred 300 Electric Shredder

E&OE © Michigan 7

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp, or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

Choking Hazard

Children under 8 yrs. Can choke

or suffocate on small parts. Adult

supervision required.

MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN

Garden Shred 300 Electric Shredder

E&OE © Michigan 8

Table of Contents

Safety ............................................................................................................................................................. 2

Safety Symbols ........................................................................................................................................................... 6

Parts Identification ....................................................................................................................................... 9

Assembly ..................................................................................................................................................... 10

Install the Wheels ..................................................................................................................................................... 10

Assembling The Stand ............................................................................................................................................. 10

Fitting The Paddle and Paddle Holder ...................................................................................................................... 11

Connecting The Extension Cord ............................................................................................................................... 11

Operation ..................................................................................................................................................... 12

Basic Shredding Operation ....................................................................................................................................... 12

Overload Protection .................................................................................................................................................. 14

Maintenance ................................................................................................................................................ 15

General Maintenance ............................................................................................................................................... 15

Cutting Blades Replacement .................................................................................................................................... 15

Carbon Brush Replacement ..................................................................................................................................... 16

Cleaning and Storage ................................................................................................................................. 18

Cleaning .................................................................................................................................................................... 18

Storage ..................................................................................................................................................................... 18

Transport .................................................................................................................................................................. 18

Recycling .................................................................................................................................................................. 18

Troubleshooting ......................................................................................................................................... 19

Specifications ............................................................................................................................................. 20

MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN

Garden Shred 300 Electric Shredder

E&OE © Michigan 9

Parts Identification

No. Name No. Name

1 Hopper Locking Knob 7 Main body

2 Switch button 8 Paddle Holder

3

Motor

9

Paddle

4

Stand assembly

10

Wheels (two)

5

Wheel axle

11

Collection bag

6

Hopper

Spare parts available

for purchase, scan QR

code below:

MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN

Garden Shred 300 Electric Shredder

E&OE © Michigan 10

Assembly

This product requires assembly. Carefully remove the product and any accessories from the box. Make

sure that all items listed in the packing list are included. Inspect the product carefully to make sure no

breakage or damage occurred during shipping. Do not discard the packing material until you have

carefully inspected and satisfactorily operated the product. If any parts are damaged or missing, contact

the manufacturer.

WARNING! The equipment and packaging material are not toys. Do not let children play with plastic

bags, foils, or small parts. These items can be swallowed and pose a suffocation risk!

Install the Wheels

WARNING! To avoid injury from accidental startups, always ensure that the tool is switched OFF and

unplugged from the power supply before adjusting or installing or removing blades.

1. Insert the wheel axle (Fig. 1 - 1) through the bottom holes of the stand.

2. Install the wheels onto both ends of the wheel axle. Secure each wheel with a nut.

3. Press the two wheel covers onto both ends of the axle.

Assembling The Stand

1. Insert the two ends of the stand assembly into the bottom of the shredder housing (Fig. 1 - 2).

2. Align the holes and secure the two screws on both sides of the stand (Fig. 1 - 3).

MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN

Garden Shred 300 Electric Shredder

E&OE © Michigan 11

Fitting The Paddle and Paddle Holder

1. Clip the paddle holder (Fig. 2 - 1) onto one side of the stand.

2. Clip the paddle (Fig. 2 - 2) into the paddle holder.

NOTE: Place the paddle back into the paddle holder every time after using.

Connecting The Extension Cord

1. Make sure the power switch is in the OFF position.

2. Select the correct extension cord.

3. Make a knot with the power cord and the extension cord as shown in Fig. 3.

MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN

Garden Shred 300 Electric Shredder

E&OE © Michigan 12

Operation

WARNING: In some countries, regulations define at what time of the day and on what special days

products are allowed to be used and what restrictions apply! Ask your community for detailed

information and observe the regulations in order to preserve a peaceful neighbourhood and avoid

committing administrative offences.

WARNING: To prevent serious injury, make sure all the instructions have been read and understood

before operating this tool. Check that the power switch works properly before plugging the tool into the

power supply.

Basic Shredding Operation

WARNING: Always wear safety glasses, ear protection and work gloves during operation. Avoid wearing

loose clothing and accessories.

WARNING: Keep your face and body away from the openings. Do not allow any part of the body or

clothing near the feeding chute or the discharge chute.

1. Place the shredder on a dry, level ground in the upright position. Do not operate the shredder if it is tilted or

lying on its side.

2. Check to make sure that the hopper is empty. Close the hopper tightly by turning the hopper lock knob (Fig 4

- 1) clockwise. The shredder will not run if the hopper is open or not fully closed.

3. Inappropriate materials may damage the machine and cutting blades. Examine all materials before feeding

them into the shredder:

•

Remove pieces of metal, rocks or other foreign objects that may damage the blades.

•

Do not feed wooden sticks with a diameter larger than 1.5 inch.

•

Before shredding roots, remove any remaining soil and stones.

•

Do not shred soft, damp material such as kitchen waste.

NOTE: For optimal performance, we recommend shredding materials with diameters smaller than 1

inch.

MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN

Garden Shred 300 Electric Shredder

E&OE © Michigan 13

4. Connect the shredder to the power source and turn the power switch to ON (Fig. 4 - 2).

NOTE: The power switch is equipped with a safety key to prevent children from accidentally starting

the machine. Turn off the power switch and remove the safety key to engage the child-safety lock

and prevent unwanted start-ups. The switch cannot be turned on when the safety key is removed.

5. Follow the rules below when feeding materials:

•

Only insert as much material as needed to prevent blockage of the feeding chute.

•

Feed wilted and damp materials alternately with dry branches to prevent cutting blades from blocking up.

•

Branches with leaves must be completely processed before new material is fed. Make sure that the

chopped material can fall freely from the discharge chute.

•

Maintain the working speed of the shredder and do not overload it.

•

Keep a few dry branches to be shredded at the end, as they will help clean your shredder.

6. Slowly insert the material to be shredded into the hopper through the feeding chute (Fig. 6). Keep hold of

branches at a safe distance from the feeding chute until they are automatically drawn into the shredder.

WARNING: DO NOT put your hands into the feeding chute. Never reach under the hopper until the

shredder has come to a complete stop and has been disconnected from the power supply.

7. Use the included paddle to push the material inside the hopper but be careful not to shred you paddle.

8. Only switch off the shredder after all of the shredding materials have passed through the discharge chutes.

Otherwise, the discharge chutes may jam the next time the shredder is turned on.

9. When all shredding work is complete, switch the machine to OFF and unplug the power cord. Wait for the

blades to come to a complete stop before leaving the work area.

MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN

Garden Shred 300 Electric Shredder

Overload Protection

Your electric shredder is equipped with overload protection. If the shredder is clogged during shredding, the

overload protection will cut the power automatically to protect your shredder. Wait at least 1 minute for the motor

to cool down before restarting the unit.

1. To restart the shredder, first press the reset button (Fig. 5 - 1). Then turn on the power switch.

2. If the shredder will not start, it might be jammed inside. Turn off the machine and unplug the power cord.

Wait for the blades to come to a complete stop before attempting to clear the clogged materials.

MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN

Garden Shred 300 Electric Shredder

Maintenance

ATTENTION: Surface corrosion will occur on metal surfaces over time and the rate of oxidation

depends on factors such as proximity to the ocean and humidity or condensation of water

vapour on metal surfaces. To mitigate this, WD40 can be used to remove surface corrosion then, when

applied periodically, it will prevent rust from forming.

WARNING: Before performing any cleaning or maintenance, disconnect the unit from the power supply.

Never touch the moving blades. Wear protective gloves! Maintain this product regularly and carefully! If

the product is improperly maintained, it may fail at its intended task, which may produce fatal

consequences. Wear protective clothing and observe all safety instructions to prevent serious personal

injury.

General Maintenance

1. Keep the product clean. Remove debris from it after each use and before storage.

2. Regular and proper cleaning will help ensure safe use and prolong the life of the product.

3. Inspect the product before each use for worn and damaged parts. Do not operate it if you find broken and

worn parts.

WARNING: Only perform repairs and maintenance work according to these instructions! All further

works must be performed by a qualified specialist!

Cutting Blades Replacement

•

The electric shredder is installed with two cutting blades that can be reversed or replaced to keep the cutting

edges sharp. The two blades should always be reversed or replaced as a matched set.

•

It is recommended to replace/reverse the blades when the wood sticks cannot be automatically drawn into

the shredder after entering the hopper. One set of sharp edges can cut approximately 400lbs of materials,

depending on the hardness and quality of the sticks.

•

When the cutting capacity is reached, make sure to replace/reverse the shredder blades to maintain optimal

performance.

WARNING: WEAR PROTECTIVE GLOVES TO PROTECT YOUR HANDS. Planer blades are sharp and

fragile. Handle the blades carefully to avoid personal injury or damage to the blades.

1. Switch off and disconnect the shredder from the power supply. Wait for the blades to come to a complete

stop.

2. Fully unscrew the hopper locking knob (Fig. 4 - 1) until it springs out. Open the hopper to access the cutting

head (Fig. 6).

3. Clean out all chips or foreign matter sticking to the cutting head and blades using a soft brush.

4. Rotate the cutting head to the configuration shown in Fig. 6. To prevent the cutting head from rotating during

blade change, insert a rod through the blade guard hole (Fig. 6 - 1) and the slot in the cutting head.

WARNING: The cutting blades have sharp cutting edges on both sides. Make sure to wear work

gloves to prevent injuries. Each blade is secured with two hex bolts (Fig. 6 - 2). Remove the blade

from the inner edge of the blade guard where both hex bolts can be accessed. Unscrew the hex bolts

counterclockwise using a hex wrench and remove the blade. Turn the cutting head 180 degrees to

remove the other blade.

5. The blades may be reversed when one of the cutting edges becomes dull or chipped. Reverse the direction

of the original blades or install two new blades. Make sure to reverse or replace both blades at the same

MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN

Garden Shred 300 Electric Shredder

time so they are balanced with one another. Align the slots on the blade with the grooves on the cutting

head.

6. Secure each blade with two hex bolts and firmly tighten using a hex wrench. Close the hopper and fully

tighten the hopper locking knob.

Carbon Brush Replacement

To maintain maximum efficiency of the motor, inspect the carbon brushes regularly and replace them when the

brush length gets down to 3/16 of an inch. The two carbon brushes can be accessed through the front and back

carbon brush cover located on the bottom of the shredder body. To inspect or replace the carbon brushes:

1. Switch off and disconnect the shredder from the power supply.

2. Unscrew the Phillips head screw from the housing and open the carbon brush cover (Fig. 7).

3. Unscrew the two small Phillips screws inside (Fig. 7) to remove the

4. Replace the carbon brush holder and carbon brush cover. Tighten all screws.

5. Repeat the steps above to replace the carbon brush located on the other side of the motor.

MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN

Garden Shred 300 Electric Shredder

MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN

Garden Shred 300 Electric Shredder

Cleaning and Storage

Cleaning

WARNING: Always switch the product off and disconnect the unit from the power supply and let the

product cool down before performing inspection, maintenance, and cleaning work!

•

Use a small brush to clean the outside of the unit. Do not use strong detergents. Household cleaners that

contain aromatic oils such as pine and lemon, and solvents such as kerosene, can damage plastic. Wipe off

any moisture with a soft cloth.

•

Inspect the product before and after each use for worn and damaged parts. Do not operate it if you find worn

and damaged parts.

NOTE: If the cutting blade is blocked by foreign objects during the operating, stop the product, wait for

the cutting blade stops entirely, remove the foreign objects and clean the cutting blade.

WARNING: Only perform repairs and maintenance work according to these instructions! All further

works must be performed by a qualified specialist!

Storage

1. Clean the product as described above.

2. Store the product and its accessories in a dark, dry, frost-free, well-ventilated place.

3. Always store the product in a place that is inaccessible to children. The ideal storage temperature is between

10 °C and 30 °C.

4. It is recommended to use the original package for storage or covering the product with a suitable cloth or

enclosure to protect it against dust.

Transport

1. Clean the product as described above.

2. Always carry the product by its handle.

3. Protect the product from any heavy impact or strong vibrations which may occur during transportation in

vehicles.

4. Secure the product to prevent it from slipping or falling over, damage or injury.

Recycling

The product comes in a package that protects it against damage during shipping. Keep the

package until you are sure that all parts have been delivered and the product is function properly.

Recycle the package afterwards.

Old products are potentially recyclable under Waste Electrical and Electronic Equipment (WEEE)

Directive(2012/19/EU) and do not, therefore, belong in your household rubbish. You are requested

to assist us and our contribution to saving resources and protecting the environment by handing in

this appliance at an equipped collection centre (if there is one available).

MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN

Garden Shred 300 Electric Shredder

Troubleshooting

PROBLEM POSSIBLE CAUSE SOLUTION

Product does not start

The power cord or extension cord is

damaged or not properly plugged in.

Check the power cord, extension cord,

power plug and the power outlet. Do

not use if any cord is damaged.

Safety key is removed from power

switch.

Check that the hopper is closed, and

the hopper lock knob is tightened.

The hopper is open.

Check that the hopper is closed, and

the hopper lock knob is tightened.

Motor is overloaded and circuit

breaker trips.

The material may be too much or too

hard for the shredder to handle. Wait

for motor to cool down and press the

reset button. Reduce the material load

and restart the shredder.

Material cannot be fed

The material is jammed in the feed

inlet.

Turn off and unplug the machine.

Open the hopper and remove blocked

or jammed materials.

The cutting blades are blocked.

Turn off and unplug the machine.

Open the hopper and blade cover.

Remove blocked material from the

blade. Close the blade cover and

hopper.

The discharge chute is blocked.

Turn off and unplug the machine.

Open the hopper and the plate of the

discharge chute to clear the blocked

material. Replace the plate and

hopper.

Inefficient cutting

Cutting blade edges are worn.

Reverse the blades or replace with

new blades.

If further assistance is required, take the unit to a qualified service dealer.

MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN

Garden Shred 300 Electric Shredder

Specifications

Rated Power 2500W

Input voltage 240V AC

Max branch diameter 40mm

No-Load Speed 5000 RPM

Transmission System Belt Drive

Power Cable Length 35cm

Power Plug Australian Standard

Noise Level 108dB

Note: Minimal Assembly

MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN MICHIGAN

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety



Consult all documentation, packaging,

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.



Before each use, check the product for

loose/broken/damaged/missing parts,

wear, or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear, or leaks.



Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.



Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.



The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.



This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business,

or employee, or financially affect the user, business, or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement, or service by a

technician may cause financial loss, loss of employee

time or an inconvenience requiring compensation.



If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

diagrams, or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning, or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

MICHIGAN GDTSRDMC3C0A 2400W Electric Garden Mulcher Shredder Portable Wood Chipper

Product's Documents

Product manual

Specifications

MICHIGAN GDTSRDMC3C0A Questions and Answers