PREMIER ELECTRONIC MICRO SOLDERING
TORCH
MODEL NO: AK2933.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
equipment, make sure you know where the nearest fire extinguisher is.
WARNING! Always wear approved eye / face protection when operating the torch.
WARNING! DO NOT use the torch if you notice it is damaged or if there could be a gas leak from it.
WARNING! Butane gas is extremely flammable, handle with care.
WARNING! Always point the torch away from the eyes and body when igniting and during operation.
WARNING! DO NOT put the torch down when it is lit, DO NOT leave it unattended.
WARNING! The flame is not easily visible in bright daylight.
WARNING! Ensure the flame is completely extinguished after use. DO NOT use water to cool the torch down.
WARNING! Only use in a well ventilated area.
8 DO NOT use the torch in an area where paint fumes, solvents or other flammable solids, liquids or gases pose a potential hazard. Keep
flammable material away from the torch when operating.
8 DO NOT operate the torch when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8 DO NOT hold any workpiece by hand.
8 DO NOT touch the workpiece close to the heated area as it will be very hot. Allow to cool.
8 DO NOT operate the torch if it is damaged as this may cause failure and/or possible personal injury.
8 DO NOT touch the tip of the torch during or immediately after use, as it will be very hot. Allow to cool.
8 DO NOT allow children to operate the torch.
9 After use allow the torch to cool before storing it.
9 When not in use, store away from direct sunlight in a safe, dry, childproof location.
8 DO NOT store at over 40°C, such as in a car in hot weather.
2. INTRODUCTION
Piezoelectricignitionwith1300°Cburnerameadjustablefrom12to35mm.Fittedwithsafetylockandcontinuoususeswitchforeasy
operation.Standardllgivesapproximately30minutescontinuousoperation.PoweredbyButane(lighterfuel).
3. op OPERATION
Refer to
instruction
manual
Wear eye
protection
Warning hot
surface
AK2933.V2Issue111/01/24
Original Language Version
© Jack Sealey Limited
Warning
flammable
material
g.1
g.2
Flame
size
control
Trigger
Trigger lock
Safety lock
Gasllingpoint
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 sales@sealey.co.uk www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceableandrequiresdisposal,drainanyfluids(ifapplicable)intoapprovedcontainersanddisposeoftheproductandfluids
according to local regulations.
AK2933.V2Issue111/01/24
Original Language Version
© Jack Sealey Limited
REGISTER YOUR
PURCHASE HERE
Note:Itisourpolicytocontinuallyimproveproductsandassuchwereservetherighttoalterdata,specificationsandcomponentparts
without prior notice. Pleasenotethatotherversionsofthisproductareavailable.Ifyourequiredocumentationforalternativeversions,
pleaseemailorcallourtechnicalteamontechnical@sealey.co.ukor01284757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty:Guaranteeis12monthsfrompurchasedate,proofofwhichisrequiredforanyclaim.
3.1. FILLING (Refertofig.1)
3.1.1. Usestandardbutanefuel.Fillinawellventilatedareaawayfromopenflame.Turnthetorchoff,makesuretheflameisextinguished,
allow to cool down for five minutes before filling.
3.1.2. Hold torch upside down and insert the filling can’s nozzle into the gas filling valve. Press nozzle into the valve and release gas. Once gas
begins to seep out around the edge of the nozzle, the gas tank is full. Remove the filling can.
3.2. OPERATION(Refertofig.1)
3.2.1. Slide safety lock down.
3.2.2. Press the trigger to ignite, release the trigger to extinguish the flame.
3.2.3. Slide the trigger lock up after ignition to keep a continuous burning flame, without holding down the trigger. Slide the lock down to
extinguish the flame.
3.2.4. Moveflamesizecontrol(fig.2)tovaryflamestrength,+toincrease,-todecrease.
