Loading ...
Loading ...
Loading ...
Low Ba�ery Return-To-Home (RTH)
The drone will perform a Low Ba�ery Return-To-Home func�on when the
ba�ery is low. If the ba�ery icon on the LCD screen shows “ ”, the
indicator lights flash red slowly and you will hear a steady “DiDiDi…DiDiDi”
sound. This is a no�fica�on that your drone’s ba�ery is low and it is �me to
bring it home. If the drone’s al�tude is over 100 feet or the drones distance
is 330 feet away, the drone will automa�cally fly back to the original Home
Point.
If the ba�ery icon on the LCD screen shows “ ”, and you hear a steady
“Di…Di” sound, this is a no�fica�on that your drone’s ba�ery is very low
and it is �me to bring it home. If the drone’s al�tude is over 50 feet or the
drones distance is over 50 feet away, the drone will automa�cally fly back
to the original Home Point.
If the drone flying al�tude is less than 50 feet or the flying distance is less
than 50 feet, then drone will automa�cally land to the ground.
Flight Modes (con�nued)
Flight Modes (con�nued)
The Return-to-Home (RTH) procedure brings the drone back to the last
recorded Home Point. There are 3 types of RTH procedures: Smart RTH,
Fail-Safe RTH and Low Ba�ery RTH.
The following sec�on describes the Home Point and GPS signal in detail.
The Home Point is the loca�on
from where the drone takes off. A
strong signal of at least 7 satellites
must be present prior to take off
in order for the drone to remem-
ber the home point.
Home
Point
GPS Descrip�on
Smart RTH
If a strong GPS signal is available (more than 7 satellites on the LCD
screen) and the Home Point is recorded at takeoff, press the Return-To-
Home bu�on. The drone will fly back to the Home Point. You must use
the Remote Controller to guide the drone around any obstacles during the
Smart RTH procedure. You can press the RTH bu�on again to exit RTH
procedure and regain the control of the drone.
PLEASE NOTE: The drone does not have sensors allowing it to avoid
obstacles. The drone must always be flown in a wide-open area and
must be manually controlled to avoid obstacles. Use cau�on when
using the Return-To-Home (RTH) func�on and make sure the drone
does not end up on a roo�op, a tree, or any other obstacle that may be
in the way during return and descent.
Fail-Safe Return
Fail-Safe RTH will be triggered if the remote controller signal is lost for more
than 6 seconds. The GPS control system will guide the drone automa�cally
to the last recorded Home Point. Regain control of the drone by pressing the
RTH bu�on if the remote controller signal is recovered.
● During the Fail-Safe Return procedure, the drone cannot avoid
obstacles
(there is no auto-detec�on sensors for any obstacles).
● The drone cannot Return-To-Home if the GPS signal is weak (satellites
number is less than 7).
● If there is no GPS signal, and remote controller signal lost for more
than 6 seconds, the drone will not Return-to-Home but descend slowly
un�l it lands on the ground and is locked.
● When returning home automa�cally, if the drone flies above 50 feet,
the drone will immediately perform the return opera�on. When the
al�tude is lower than 50 feet, the drone will automa�cally rise to 50 feet
before performing the return opera�on (the return al�tude can be set in
the APP) .
WARNING: You can regain control of the drone by pressing the RTH
bu�on if the ba�ery icon on the LCD screen shows “ ”. But when the
ba�ery icon on the LCD screen shows “ ”, you can not regain control
of the drone by pressing the RTH bu�on.
22 23
Loading ...
Loading ...
Loading ...