Jet-USA PRWCLNJT21SA 21" Stainless Steel Pressure Washer User Manual

User Manual

[Revision 1.0 November 2022]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY

VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may vary in appearance,

assembly, inclusions, specifications, description, and packaging.

21” Surface Cleaner

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases, or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

• Work areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

• Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol, or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory, or

mental capabilities.

General Fuel Safety

• Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

• Always refuel in well ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start, or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

• Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors, and

vents.

General Equipment Use and Care

• The equipment is designed for domestic

use only.

• Handle the equipment safely and carefully.

• Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage, or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

• Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

• Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

• Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases, or liquids etc.

• The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

• Do not clean equipment with solvents,

flammable liquids, or harsh abrasives.

• For specific equipment safety use and care,

see Equipment Safety.

21” Surface Cleaner

General Electrical Safety

• Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Wherever possible, use a residual current

device (RCD).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

• Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

• The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories, or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service-related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

Child Choking Hazard!

• WARNING: CHOKING HAZARD - CHILDREN UNDER 8 YRS. CAN CHOKE OR SUFFOCATE ON SMALL PARTS. ADULT

SUPERVISION REQUIRED.

• Carefully inspect anything a baby or child could gain access to, including this product & packaging.

• Dangers include anything of a size that could become stuck or lodged in a baby or child's airway.

• Dangers include things like raw, hard fruit and vegetable pieces, large pieces of meat, bones or sausage skins, popcorn, nuts,

hard lollies and corn chips, small magnets and batteries, coins, beads, marbles and small uninflated balloons, broken toys and smaller toys,

buttons, keys and coins. But there are also many more.

• Pay particular attention to accessories, nuts, bolts, screws, washers, caps, covers, loose parts, parts that could be removed or break off, pieces

of packaging, staples, tape etc.

• In the case of any doubt, secure the item of concern in an appropriate manner, or completely remove the possibility of access by a baby or child.

Surface Cleaner Safety

HAZARD! RISK OF INJECTION OR SEVERE CUTTING INJURY! Serious injury or death could occur from high pressure spray penetrating

the skin.

• Keep clear of nozzle and spray! Never put your hand, fingers or body directly over the spray nozzle. Never point the high-pressure discharge

spray at yourself or anyone else.

• This product is to be used only by trained operators. Always keep operating area clear of all persons.

• DO NOT allow children to operate this unit.

• If an accident does occur, and the spray appears to have penetrated the skin, SEEK EMERGENCY MEDICAL CARE. DO NOT TREAT AS A

SIMPLE CUT! Be prepared to tell a physician exactly what kind of cleaning agents you were using by reading the Detergent Label and the

Material Safety Data Sheet provided with your detergent.

• High pressure hoses should be inspected daily for signs of wear. If evidence of failure exists, promptly replace all suspect hoses to prevent the

possibility of injury from the high-pressure spray. If a hose or fitting is leaking, NEVER PLACE YOUR HAND DIRECTLY ON THE LEAK.

• Before using rotary surface cleaner, or when quick connecting high pressure hoses, be certain the " collar" on the female quick connect is locked

securely to prevent accidental discharge and that all quick coupler fittings are secure.

• NEVER operate the gun with the trigger wired in the open position. To prevent accidental discharge, the trigger gun should be securely locked

when not in use.

• Do not make repairs or adjustments while unit is running.

• Before removing the spray nozzle or servicing the unit, ALWAYS shut off the unit and trigger the gun to release trapped pressure. (Even after you

shut off the unit, there is high pressure water left in the unit until you release it by triggering the gun.) Allow the unit to cool down and service in a

clean, dry, flat area.

HAZARD! RISK OF BURNS! Serious injury may occur from touching Hot Surfaces

• The Rotary Surface Cleaner is capable of reaching a maximum of 100°C (212°F). When using in a hot water application, do not touch or direct

discharge stream at people. Be cautious of hose fittings as surface temperatures are same as the water temperature.

HAZARD! RISK OF BODILY INJURY! Serious injury or death may occur from detergents contacting or penetrating the skin.

• SEEK EMERGENCY MEDICAL CARE if the spray appears to have penetrated the skin! DO NOT TREAT AS A SIMPLE CUT! Be prepared to tell

a physician exactly what kind of cleaning agents you were using by reading the Material Safety Data Sheet provided with your detergent.

• Never use any solvents or highly corrosive detergents or acid type cleaners with this rotary surface cleaner.

• Protective equipment such as rubber suits, gloves and respirators are advisable, especially when using cleaning detergents.

• Keep all detergents out of the reach of children!

21” Surface Cleaner

Serious injury can occur from loose debris being propelled at a high speed from the spray gun.

• ALWAYS wear protective goggles when operating the unit to shield the eyes from flying debris and detergents.

• DO NOT direct spray toward fragile materials such as glass for shattering could occur.

Injury may occur if the operator loses his balance caused by the thrust of water travelling through the spray nozzle.

• Stay alert-watch what you are doing. Do not operate the unit when fatigued or under the influence of alcohol or drugs.

• NEVER squeeze the trigger unless securely braced.

• DO NOT overreach or stand on unstable support.

• Wet surfaces can be slippery, wear protective foot gear and keep good footing and balance at all times.

Injury may occur from the rotary surface cleaner.

• ALWAYS hold on firmly to the handles of the Rotary Surface Cleaner when operating the unit. Failure to do so can cause the Cleaner to move

dangerously. To prevent accidental discharge, the trigger gun should be securely locked when not in use.

• Always wear eye and ear protection when using the Rotary Surface Cleaner. Other protective clothing such as a rubber suit, gloves, respirator,

etc., may be necessary when using detergents.

• Never make adjustments on the machine while in operation.

• DO NOT leave pressurized unit unattended. Shut off the pressure washer and release trapped pressure before leaving.

• Know how to stop the Rotary Surface Cleaner. Be thoroughly familiar with controls.

21” Surface Cleaner

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases, or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases, or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing, and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

21” Surface Cleaner

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp, or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

Choking Hazard

Children under 8 yrs. Can choke

or suffocate on small parts. Adult

supervision required.

21” Surface Cleaner

Table of Contents

Safety ............................................................................................................................................................. 2

Safety Symbols ........................................................................................................................................................... 5

Parts Identification ....................................................................................................................................... 8

Assembly ....................................................................................................................................................... 9

Nozzle Selection & Installation ................................................................................................................................... 9

Unit Assembly ............................................................................................................................................................. 9

Set-Up ....................................................................................................................................................................... 10

Surface Preparation .................................................................................................................................................. 10

Pre-Start Inspection Procedures .............................................................................................................................. 11

Operation ..................................................................................................................................................... 12

Special Application Areas ......................................................................................................................................... 12

Benefits of Pressure Washer Surface Cleaners ....................................................................................................... 12

Starting Up ................................................................................................................................................................ 13

Shutting Down .......................................................................................................................................................... 13

Troubleshooting ......................................................................................................................................... 15

Specifications ............................................................................................................................................. 16

21” Surface Cleaner

Parts Identification

Unpack the machine and make sure that it is complete and not damaged. In case it is not complete or

damaged, do not use the machine and consult your dealer. For reasons of packaging or transport, some

accessory components can be supplied loose. In this case they must be assembled according to the

instructions in this manual. Make sure that the components of the packaging are placed out of the reach

of children.

No. Name No. Name

1

Box

5

Clevis Pin x 3pcs

2 Inserts 6 Bridge Pin x 3pcs

3

Hose

7

Lower handle

4 Upper handle 8 Cover assembly

JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA

21” Surface Cleaner

Assembly

Nozzle Selection & Installation

1. Your Rotary Surface Cleaner will come installed with one set of 25020 nozzles (25degree and 2.0 orifice).

a. The minimum orifice size to be used in your Rotary Surface Cleaner is half that which is being used in

your pressure washer.

Example: If your pressure washer uses a size 5 orifice, you will need to use a size 2.5 orifice in your

Rotary Surface Cleaner.

(Two nozzles are inserted in the Rotary Surface Cleaner, therefore; two nozzles x size 2.5 orifice = size

5 orifice.)

b. The nozzles being used should have a 15° - 25° spray pattern; anything less than a 15° spray pattern

can damage the area being cleaned. Anything more than 25° may not allow the bar to rotate.

2. Nozzles should be screwed into the rotating bar. The spray fan should be parallel to the Rotating Bar (See

figures below).

Unit Assembly

1. Line up the holes on the lower part of handle (7) with the holes on the cover assembly (8).

2. Insert the clevis pins (5) through the handle and cover holes and attach to the bridge pins (6).

3. Attach the upper handle (4) by lining up the hole in the upper and lower handle. Push the clevis pin (5)

through the aligned hole and attach to the bridge pin (6).

4. Quick connect the Rotary Surface Cleaner hose assembly to the handle centre and to the swivel located on

the unit base.

JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA

21” Surface Cleaner

Set-Up

1. Locate the high-pressure discharge hose on your pressure washer and ensure it is securely connected to

the water outlet of the pressure washer. Quick connect the other end of the high-pressure discharge hose to

the gun on the Rotary Surface Cleaner.

2. Connect the water supply hose, one end to your pressure washer, the other end to a pressurized water

supply.

Surface Preparation

1. Clear any loose debris from the area to be cleaned.

2. Never attempt to clean surface with objects that protrude from the surface being cleaned. Striking any raised

obstacle during operation will damage machine. If contact does occur and results in vibration when operating

machine, STOP and replace spray bar.

JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA

21” Surface Cleaner

CAUTION! Risk of Injury or damage to machine! NEVER OPERATE THE UNIT IF IT BEGINS TO VIBRATE!

Shutdown the unit and tighten the rotating bar, bolts and fittings.

Pre-Start Inspection Procedures

1. Inspect Rotary Surface Cleaner before each use. Tighten rotating bar, bolts and fittings as needed.

2. Ensure all connections are secure. Turn the water supply completely "ON". (DO NOT START PRESSURE

WASHER!)

3. Inspect hoses for kinking, cut or leaks. If found, DO NOT USE HOSE! Replace damaged hoses before

starting.

4. Unlock the trigger gun and squeeze the trigger. Water will begin flowing from the nozzles of the Surface

Cleaner. Ensure nozzles are not clogged and spray pattern is not erratic. Change nozzles before proceeding

if problems exist.

5. Be sure that all damaged parts are replaced and that the mechanical problems are corrected prior to

operation. If you need service, contact an Authorised Service Centre.

JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA

21” Surface Cleaner

Operation

Special Application Areas

•

Removing deposits, mass, algae, fuel, oil and grease from drive through pads, boat ramps, tennis courts,

roofs, pools, decks, walkways, factory floors, semi-trailer floors, fishing docks, and loading docks.

•

Cleaning off stubborn stains from asphalt and concrete surfaces.

•

Disinfection for the highest hygiene demands in saunas, bathroom areas, and in the catering industry.

•

Great for cleaning driveways.

The following comparison chart shows the time taken to clean a typical driveway (37 sq. meter) using 2 different

components.

ATTACHMENT TIME

Rotary surface cleaner 10 minutes

Standard spray nozzle 80 minutes

Benefits of Pressure Washer Surface Cleaners

•

Huge time savings.

•

Easy, effortless work.

•

Substantially lower cost (especially labour).

•

Visibly greater cleanliness.

•

Universally applicable.

•

Use with cold or hot water.

•

Circular design allows a zero-wall clearance.

•

Hover action (cleaner "floats" above the ground).

•

Eliminates streaking and fatigue.

JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA

21” Surface Cleaner

Starting Up

WARNING! Do not attempt to operate this rotary surface cleaner until you have read and understood all

safety warning and instructions listed in this manual. Incorrect operation of this unit can cause serious

injury! Do not alter or modify this equipment in any manner!

1. Connect your pressure washer to the surface cleaners trigger assembly via the 3/8 quick connector.

2. Lock the trigger gun on the Rotary Surface Cleaner by moving the safety lock lever to a 90° angle so it rests

against the handle grip.

3. Ensure all connections are secure.

4. Unlock the trigger gun and squeeze the trigger while starting the Pressure Washer.

5. Water will begin flowing from the nozzles of the Surface Cleaner. Ensure nozzles are not clogged and spray

pattern is not erratic. Turn the pressure washer and water supply off and change nozzles before proceeding

if problems exist.

6. Walk slowly behind the unit, cleaning as you go. If striping occurs, slow down the pace. Do not allow

machine to remain stationary on soft surfaces such as wood.

7. Check "weep hole" on top of the swivel periodically. Water will seep slowly. If it shoots out, shut-down the

unit and replace seals and/or main seal.

CAUTION! Risk of Injury or damage to machine! NEVER OPERATE THE UNIT IF IT BEGINS TO VIBRATE!

Shutdown the unit and tighten the rotating bar, bolts and fittings.

Shutting Down

1. Turn the Pressure Washer OFF.

2. Turn the water supply OFF.

3. Squeeze the trigger gun to relieve water pressure.

4. Disconnect and drain the water hose and wipe down unit. Store unit in a non-freezing environment.

JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA

21” Surface Cleaner

JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA

21” Surface Cleaner

Troubleshooting

PROBLEM PROBABLE CAUSE REMEDY

Inadequate cleaning power.

1. Not enough PSI from pressure

washer.

2. Inadequate water supply.

3. Engine RPM on pressure washer

is too low.

4. Nozzle obstructed or worn.

5. Incorrect nozzle orifice size.

1. Ensure unit produces a minimum

2000PSI. Most effective cleaning

range is 2500 - 4000PSI.

2. Turn water supply completely

"ON" and/ or clean water filter on

pressure washer. Ensure unit

produces a minimum of 3.0 GPM.

3. Increase throttle.

4. Clean or replace as necessary.

5. Insert correct nozzle.

Rotating bar will not rotate.

1. Seal has drag.

2. Snap ring dislodged.

3. Seal malfunction.

4. Bearing failure.

1. Allow for break-in period.

2. Do not use! Contact the

manufacturer or an authorised

service centre.

3. Do not use! Contact the

manufacturer or an authorised

service centre.

4. Do not use! Contact the

manufacturer or an authorised

service centre.

Excessive vibration of Surface

Cleaner OR Cleaner base is

creating a suction to the

surface.

1. Nozzle clogged.

2. Rotating bar, bolts or fittings

loose.

3. Rotating bar or swivel rotor bent.

1. Clean or replace.

2. Tighten.

3. Replace.

Streaked cleaning pattern.

1. Insufficient water supply OR PSI

of pressure washer is too low.

(Won't allow Rotating Bar to

move.)

2. Nozzle clogged.

3. Cleaning too fast.

1. Increase water supply OR ensure

pressure is a minimum of 2000

PSI and GPM is a minimum of

3.0.

2. Clean or replace.

3. Slow down pace.

Water leaking from swivel.

Small amount of leakage is normal. No modification is necessary.

Water shooting from swivel.

Seal malfunction. Replace.

JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA

21” Surface Cleaner

Specifications

Size 53cm (21”)

Body Stainless Steel (304 Grade)

Hose Fitting 3/8” Quick Connector

Max. Water Temperature 90°C

Note: Minimal Assembly Required

JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA JET USA

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety



Consult all documentation, packaging,

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.



Before each use, check the product for

loose/broken/damaged/missing parts,

wear, or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear, or leaks.



Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.



Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.



The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.



This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business,

or employee, or financially affect the user, business, or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement, or service by a

technician may cause financial loss, loss of employee

time or an inconvenience requiring compensation.



If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

diagrams, or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning, or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

Jet-USA PRWCLNJT21SA 21" Stainless Steel Pressure Washer Surface Cleaner

Product's Documents

Product manual

Specifications

Jet-USA PRWCLNJT21SA Questions and Answers