STANDARD GOGGLES - INDIRECT VENT
MODEL NO: 201, 201/10
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT
IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE
WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. INTRODUCTION
Clear polycarbonate safety lens with indirect ventilation in the frame. Conforms to BS EN 166:2001, optical class 1 impact grade B.
Notied Body: 2797
Type Examination Certicate Number: CE 714723
Carried Out By: BSI Group Netherlands B.V., John M. Keynesplein 9, 1066 EP Amsterdam, The Netherlands
2. SAFETY
WARNING! The product protects against high speed particles worn over standard ophthalmic spectacles, but may transmit impacts,
thus creating a hazard to the wearer.
9 Ensure the goggles t well to avoid slippage and discomfort.
9 Adjust the headband by pulling/loosening the headband through the buckle.
9 This product is designed for face and eye protection against high speed particles of medium energy impact (Class 1, Grade B, as
marked on the lens).
9 Inspect the goggles frequently as a pitted, scratched or dirty face shield reduces vision and should be replaced immediately.
9 Avoid liquids as small particles can splash into the eyes.
9 Inspect the goggles frequently as a pitted, scratched or dirty face shield reduces vision and should be replaced immediately.
8 DO NOT use if any part of the goggles is cracked or broken.
8 DO NOT place this product on a hot surface.
8 DO NOT use these goggles for protection against short circuit electric spark, ne dust, gas, ultra violet or infra red radiation, ionising
radiation, liquids under pressure or other severe hazards.
8 DO NOT use these against heavy impact hazards.
8 DO NOT use these goggles for welding.
IMPORTANT: if protection against high speed particles at extremes of temperature is required, then the selected eye-protector should
be marked with the letter ‘T’ immediately after the impact letter, i.e. FT, BT or AT. If the impact letter is not followed by the letter ‘T’ then
the eye protector shall only be used against high speed particles at room temperature. If the symbols F, B and A are not common to
both the ocular and the frame then it is the lower level which shall be assigned to the complete eye-protector.
3. APPLICATIONS
3.1. EN 166 CATEGORISATION
• Optical Class 1 - suitable for work with high vision requirements for permanent use.
3.2. MECHANICAL STRENGTH
• B - High speed particle - medium energy impact
4. MAINTENANCE
4.1. CLEANING
8 DO NOT use abrasive materials.
9 Using a soft and clean brush or cloth, use warm suds to wash and clean. Ensure hands are clean (without grease).
9 Materials which may come into contact with the wearer’s skin could cause allergic reactions to susceptible individuals. The contact
areas should be disinfected regularly.
4.2. STORAGE
9 Store in a bag or case out of direct sunlight, away from chemicals and abrasive substances, in a clean dust free environment.
9 Use original bag for transportation if possible.
4.3. OBSOLESCENCE
9 Product shelf life/expiry date is dependent on correct storage and general use.
9 Inspect the goggles frequently as a pitted, scratched or dirty face shield reduces vision and should be replaced immediately.
201, 201/10 Issue 5 (1,4) 29/11/23
Original Language Version
© Jack Sealey Limited
EU | Sealey EU Ltd, Farney Street, Carrickmacross, Co. Monaghan, A81 PK68 Ireland
UK | Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 sales@sealey.co.uk www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product
becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and
dispose of the product and fluids according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
REGISTER YOUR
PURCHASE HERE
This document has been drawn up according to Regulation (EU) 2016/425 as amended to apply to GB for Personal Protective
Equipment. The declaration of conformity can be accessed at www.sealey.co.uk.
201, 201/10 Issue 5 (1,4) 29/11/23
Original Language Version
© Jack Sealey Limited
