Loading ...
Loading ...
Loading ...
ENGLISH
14
Register Online
Thank you for your purchase. Register your product nowfor:
• WARRANTY SERVICE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with yourproduct.
• CONFIRMATION OF OWNERSHIP: In case of an
insurance loss, such as fire, flood or theft, your registration
of ownership will serve as your proof ofpurchase.
• FOR YOUR SAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
SafetyAct.
• Register online at www.dewalt.com
Repairs
The charger and battery pack are notserviceable. There are
no serviceable parts inside the charger or batterypack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should
be performed by a
DeWALT
factory service center or a
DeWALT
authorized service center. Always use identical
replacementparts.
Saw Chain Sharpness
CAUTION: Sharp chain. Always wear protective gloves
when handling the chain. The chain is sharp and can
cut you when it is notrunning.
IMPORTANT: The chain cutters will dull immediately if they
touch the ground, stones, masonry or a nail whilecutting.
To get the best possible performance from your chain saw it
is important to keep the teeth of the saw chain sharp. Chain
sharpening services are available from your nearest
DeWALT
servicecenter.
NOTE: Each time the saw chain is sharpened, it loses some
of the reduced kickback qualities and extra caution should
be used. It is recommended that a saw chain be sharpened
no more than fourtimes.
Saw Chain and Guide Bar
After every few hours of use, remove the sprocket cover,
guide bar and chain and clean thoroughly using a soft bristle
brush. Ensure oiling hole on bar is clear of debris. When
replacing dull chains with sharp chains it is good practice to
flip the chain bar from bottom totop.
Replacement chain and bar are available from your
nearest authorized servicecenter.
• This chain saw requires replacement 8" (203mm) chain
DWO1DT608.
Accessories
WARNING: Since accessories, other than those offered
by
DeWALT
, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only
DeWALT
recommended
accessories should be used with thisproduct.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service
center. If you need assistance in locating any accessory, please
contact
DeWALT
call 1‑800‑4‑
DeWALT
(1-800-433-9258) or
visit our website: www.dewalt.com.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1approved eye
protection when performingthisprocedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into aliquid.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
Your D
e
WALT power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regularcleaning.
2. Never operate while in a tree, in any awkward position
or on a ladder or other unstable surface. You may lose
control of pole saw causing severe injury.
3. Follow directions below to trim atree.
a. Make sure pole saw is running at full speed before
making a cut. When starting a cut, place moving saw
chain
7
against limb. Hold pole saw firmly in place
to avoid possible bouncing or skating (sideways
movement) of polesaw.
b. Guide pole saw using light pressure. Make first cut 6"
(152mm) from tree trunk on underside of limb. Use
top of guide bar
6
to make this cut. Cut 1/3 through
diameter of limb. Then make the finish cut from the top.
If you try to cut off thick branches from the bottom, the
branch may close in and pinch the saw chain in the cut.
If you try to cut off thick branches from the top, without
a shallow undercut, the branch may splinter. Do not
force pole saw. The motor will overload and can burn
out. It will do the job better and safer at the rate for
which it wasintended.
c. Remove pole saw from cut while it is running at full
speed. Stop pole saw by releasing trigger switch
33
.
Make sure saw chain has stopped before setting pole
sawdown.
Loading ...
Loading ...
Loading ...