Loading ...
Loading ...
Loading ...
11
ENGLISH
Installing the Guide Bar and Saw Chain
(Fig.D–G)
CAUTION: Sharp chain. Always wear protective gloves
when handling the chain. The chain is sharp and can
cut you when it is notrunning.
WARNING: Sharp moving chain. To prevent accidental
operation, ensure that battery is removed from the tool
before performing the following operations. Failure to
do this could result in serious personalinjury.
If the saw chain
7
and guide bar
6
are packed separately in
the carton, the chain has to be attached to the bar, and both
must be attached to the body of thetool.
1. Place the pole saw attachment
1
on a flat, firmsurface.
2. Rotate the bar lock nuts
3
counterclockwise with a
13mm wrench (not provided) and removethem.
DISASSEMBLY
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
Detaching Pole Saw Assembly (Fig.A–C)
WARNING: Sharp moving blade. To prevent accidental
operation, insure that battery is disconnected from the
handle and that the protective scabbard is in place on
the chain before performing the following operations.
Failure to do this could result in serious personal injury.
When detaching the assemblies, always detach the pole saw
attachment
1
first.
To Remove the Extension Pole from the Pole
SawAttachment:
1. Install scabbard
32
on guide bar andchain.
2. When removing the pole saw attachment
1
from the
extension pole
11
, loosen the knob
13
.
3. Depress the latching button
18
located on the extension
pole coupler
12
, and pull the pole saw attachment
1
away from the extension pole
11
.
To Remove the Powerhead from the extension pole:
1. When removing the extension pole
11
from the
powerhead
14
, loosen the knob
13
. Then depress the
latching button
18
and pull the extension pole
11
away
from the powerhead
14
.
4. When properly assembled, the latching button should
engage with one of the three latching holes. If it does
not, do not use, disassemble and re‑align the pole saw
attachment
1
so the latching button
18
engages one
of the three latching holes
15
,
16
,
17
in the extension
pole coupler
12
.
WARNING: Always check to make sure that the knobs
are completely secured in place. If the knobs are not
completely secured it could result in the assemblies
becoming disconnected creating a hazardous
condition. Periodically check the connections to ensure
that the knobs are completely secured inplace.
the chain before performing the following operations.
Failure to do this could result in serious personal injury.
Combining the powerhead
14
to the pole saw
attachment
1
creates a pole saw that is approximately 5.9ft
(1.8m) in length.
To Attach the Powerhead to the Pole
SawAttachment
1. The upper powerhead pole
14
is equipped with three
latching holes
15
,
16
,
17
for the latching button
18
.
2. When installing the pole saw attachment pole
1
into the upper powerhead pole
14
and align the
latching button
18
with one of the three latching
holes
15
,
16
,
17
.
NOTE: To properly engage the latching button
18
with
the latching hole
15
, slightly rotate the powerhead
pole
14
and move it axially until the latching button
engages the latchinghole.
3. Turn the knob
13
to secure theattachment.
4. When properly assembled, the latching button should
engage with one of the three latching holes. If it does
not, do not use, disassemble and re‑align the pole saw
attachment
1
so the latching button
18
engages with
one of the three latching holes
15
,
16
,
17
.
Assembling the Extension Pole to the Pole
Saw Attachment and the Powerhead
(Fig.B, C)
CAUTION: The extension pole should exclusively be
used with the pole sawattachment.
CAUTION: Only one extension pole should be used
with the pole sawattachment.
To Attach the Powerhead to the Pole
SawAttachment
Adding the extension pole
11
to the powerhead
14
and pole saw attachment
1
creates a pole saw that is
approximately 8.9 ft (2.7m) in length.
To Attach the Powerhead to the
Extension Pole and Pole Saw Attachment
1. The upper powerhead pole
14
is equipped with three
latching holes
15
,
16
,
17
for the latching button
18
.
2. When installing the extension pole
11
into the upper
powerhead pole
14
and align the latching button
18
with one of the three latching holes
15
,
16
,
17
.
3. Turn the knob
13
to secure theextensionpole.
To Attach the Pole Saw Attachment to the Extension Pole:
1. When installing the pole saw attachment
1
into the
extension pole
11
, the pole saw attachment pole
1
is
equipped with three latching holes
15
,
16
,
17
for the
latching button
18
.
2. When installing the pole saw attachment pole
1
into the
extension pole
11
and align the latching button
18
with
one of the three latching holes
15
,
16
,
17
.
3. Turn the knob
13
to secure theattachment.
Loading ...
Loading ...
Loading ...