Mountfield EMPRESS 41 LI Cordless Lawn Mower

OPERATOR’S MANUAL - Page 44

For EMPRESS 41 LI. Series: 500 Series
Also, The document are for others Mountfield models: CP1430LI48, CP1430LID48, CP1480LI48, CP1480LID48, CP1530LID48

PDF File Manual, 110 pages, Read Online | Download pdf file

EMPRESS 41 LI photo
Loading ...
Loading ...
Loading ...
EN - 5
5.2. SAFETY CHECKS
Check the integrity and correct assembly of all machine
components;
Make sure that all fasteners are tightened correctly;
Keep every surface of the machine clean and dry.
Action Result
1. Start the machine.
2. Release the switch control.
1. The cutting means should
move.
2. The levers must return to the
neutral position automatically
and quickly, the engine must
switch off and the cutting
device must stop within a few
seconds.
1. Start the machine.
2. Engage the drive lever.
3. Disengage the drive lever.
2. The machine moves forward.
3. The machine comes to a
standstill.
1. Test drive. 1. No abnormal vibrations.
No abnormal sound.
If any of the results fail to match the indications
provided in the tables, do not use the machine!
Contact a service centre to have it checked and
repaired if necessary.
5.3. START-UP AND WORK
NOTE Start the machine on a level surface free from obsta-
cles or grass.
Start the machine as shown in (Fig. 13).
IMPORTANT Always maintain a  safe distance  from  the cut-
ting  device  while  working,  corresponding  to  the  length  of  the 
handle.
Emptying the grass catcher
(Fig. 14)
1. Release the switch lever and wait for the cutting device
to stop.
2. Lift the rear discharge guard, take hold of the handle and
remove the grass catcher by holding it in an upright position.
5.4. STOP
At the end of the work, release the switch control (Fig. 15).
When you have stopped the machine, it will take
a few seconds for the cutting means to stop.
5.5. AFTER OPERATION
Cleaning procedure (Par. 5.1).
If necessary, replace the damaged components and tighten
any loose screws and bolts.
Whenever you leave the machine unused or unattended:
Open the battery housing hatch and remove the safety key
(for battery models).
6. MAINTENANCE
The safety regulations to follow are described in chap. 1. Strictly
comply with these indications to avoid serious risks or dangers.
Before conducting any inspections, cleaning or maintenance/
adjustment interventions on the machine:
Stop the machine.
Make sure that every moving component has come to
a standstill.
Remove the safety key (for battery models).
Use suitable clothing, protective gloves and goggles.
6.1. CLEANING
Clean thoroughly following the instructions below every time
it is used.
Do not spray water onto the motor and electrical
components and prevent them from getting wet.
Remove grass debris and mud accumulated inside the
chassis.
Always make sure the air intakes are free of debris.
Do not use aggressive liquids to clean the chassis.
To reduce the risk of re, keep the engine free of grass
mulch, leaves or excessive grease.
6.2. CUTTING MEANS MAINTENANCE
Do not touch the cutting device until the safety
key has been removed and the cutting device is
completely stationary. Be careful because the
cutting device can move even if the key has been
removed (for battery models).
All work on the cutting means (disassembly,
sharpening, balancing, repairing, reassembly
and/or replacing) are demanding jobs that require
special skills as well as special tools. For safety
reasons, these jobs are best carried out at a
Specialised Centre.
Make sure damaged, misshapen or worn cutting-
means are replaced, together with its own screws
in place to preserve balance.
IMPORTANT Always  use  original  cutting  devices  with  the 
code shown in the "Technical Data" table.
6.3. RECHARGE THE BATTERY
Recharge the battery as shown in (Fig. 16).
7. TRANSPORT, STORAGE AND
DISPOSAL
7.1. TRANSPORT
Whenever the machine is to be handled, raised, transported
or tilted you must:
Stop the machine.
Make sure that every moving component has come to
a standstill.
Remove the safety key (for battery models).
Disconnect the machine from the mains (for models with
electric cable).
Wear heavy work gloves.
Hold the machine in the points oering a safe grip, taking
into account the weight and its division.
Use an adequate number of people suitable to the weight
of the machine.
Make sure that machine movements do not cause damage
or injuries.
Fasten rmly to the means of transport using ropes or chains
to prevent it from tipping over causing possible damage.
Loading ...
Loading ...
Loading ...