Mountfield EMPRESS 41 LI Cordless Lawn Mower

OPERATOR’S MANUAL - Page 43

For EMPRESS 41 LI. Series: 500 Series
Also, The document are for others Mountfield models: CP1430LI48, CP1430LID48, CP1480LI48, CP1480LID48, CP1530LID48

PDF File Manual, 110 pages, Read Online | Download pdf file

EMPRESS 41 LI photo
Loading ...
Loading ...
Loading ...
EN - 4
3. ASSEMBLY
IMPORTANT Unpacking  and  assembly must  be carried out 
on a flat, solid surface with sufficient space to move the machine 
and the packaging.
1. Unpacking (Fig. 2)
2. Assembling and adjusting the handle (Fig. 3)
3. Grass catcher assembly (Fig. 4)
4. CONTROLS
Safety key (Deactivation device)
The safety key found inside the battery compartment enables
/ disables the machine electric circuit (Fig. 5).
Removing the key, the electric circuit is completely deactivated
to prevent uncontrolled use of the machine.
IMPORTANT Remove the safety key whenever the machine 
is unused or left unattended.
Operator presence lever
The operator presence lever (Fig. 6.A) enables the
engagement of the cutting device. The handle is located in
the front position.
Press the safety button (Fig. 6.C) and move the lever towards
the handle to start the cutting device.
When the lever is released, the motor automatically stops
and all functions are disabled.
Power button (if provided)
The power button (Fig. 7.A) is used for:
Switching on the machine.
Pressing the button (Fig. 7.A) the LED (Fig. 7.B) turns
on and the machine is ready for use.
NOTE The  machine  can  only  be  switched  on  if  the 
operator presence lever and the drive lever are released.
NOTE If the machine is not used, the LED turns off
after 15 seconds and the above-mentioned operation
must be carried out again.
Cutting means engagement.
NOTE The cutting device engagement is possible on-
ly by pressing  the  operator presence lever against the 
handle (see par. 6.3).
Cutting means disengagement.
With the cutting device engaged, release the operator
presence lever (Fig. 6.A); the cutting device stops
keeping the machine switched on.
Drive lever (if provided):
This engages the wheel drive and allows the machine
to move forward (Fig. 6.B). The handle is located in
the rear position.
IMPORTANT The  engine  must  always  be  running  with  the 
drive disengaged.
IMPORTANT To prevent damage to the transmission, do not
pull the machine backwards with the drive engaged.
For some models it's possible to adjust the feed speed using
the selection knob on the right of the handle (Fig. 7.C).
You can select 6 dierent levels of speed.
Maximum speed (about 5 Km/h).
Minimum speed (about 2.5 Km / h)
NOTE The last speed level selected remains set also after the
machine shutdown.
"ECO" button (if provided)
The “ECO” mode allows to save energy when cutting the grass,
optimising the battery life. To activate or deactivate the "Eco"
function, press the button (Fig. 7.D).
This mode automatically turns o when the operator presence
lever is released.
NOTE It is not recommended to use the “ECO” function in
heavy  grass  cutting  conditions  (cutting  of  dense,  high,  humid 
grass).
Cutting height adjustment
By lowering or raising the chassis the grass can be cut at
dierent heights. (Fig. 8)
IMPORTANT This  operation  must  be  carried  out  when  the 
cutting device is stationary.
5. USING THE MACHINE
IMPORTANT For instructions regarding the engine and the
battery (if supplied), read the relevant manual.
5.1. PRELIMINARY PROCEDURES
Place the machine in a stable horizontal position on the ground.
Checking the battery
Before using the machine for the rst time after purchase,
fully charge the battery following the instructions in the
battery booklet.
Before every use of the machine, check the battery charge
status according to the instructions in the battery booklet.
Preparing the machine before starting work
IMPORTANT Carry  out  this  operation  with  the  cutting  de-
vice stationary.
With this machine, it is possible to mow the lawn in several ways:
Setting up for cutting the grass and collecting it in the
grass catcher (Fig. 9)
Setting up for cutting and rear grass discharge onto the
ground (Fig. 10)
Setting up for cutting and shredding the grass ('mulching'
function) (Fig. 11)
Setting up for cutting and lateral grass discharge onto the
ground (Fig. 12)
Loading ...
Loading ...
Loading ...