Loading ...
Loading ...
Loading ...
11
ENGLISH
Repairs
The charger and batteries are notserviceable. There are no
serviceable parts inside the charger or batterypack.
WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a DeWALT factory
service center or a DeWALT authorized service center.
Always use identical replacementparts.
Nosecone Maintenance (Fig. A)
If the nose cone
4
becomes hard to turn it may be
contaminated with drywall dust.
1. Remove nose cone fromtool.
2. Rinse thoroughly with warm water while rotating both
screw depth adjustment collar
2
and locking collar
3
.
Never use oil orsolvents.
3. Dry the nosecone completely before reattaching totool.
Belt Hook (Fig. I)
WARNING: To reduce the risk of serious personal
WARNING: To reduce the risk of serious personal
injury, ONLY use the tool’s belt hook to hang the
tool from a work belt. DO NOT use the belt hook
for tethering or securing the tool to a person or object
during use. DO NOT suspend tool overhead or suspend
objects from the belthook.
WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook issecure.
IMPORTANT: When attaching or replacing the belt hook
11
, use only the screw that is provided. Be sure to securely
tighten thescrew.
The belt hook
11
can be be attached to either side of the
tool using only the screw provided, to accommodate left‑ or
right‑ handed users. If the hook is not desired at all, it can be
removed from the tool.
To move belt hook, remove the screw that holds it in place
then reassemble on the opposite side. Be sure to securely
tighten thescrew.
d. While holding the sleeve depressed, pull the bit
holderout.
NOTE: Refer to and follow all instructions on changing
bits and holders in your screwgunmanual.
3. Push and rotate the provided DCF6202PH2 phillips bit
for collated drywall screwgun attachment
25
into the
spindle until ball lock snaps in groove of the bitshank.
4. With the the nose cone removed and provided driver bit
installed, push the DCF6202 collated drywall screwgun
attachment
24
over the bit onto the screw driver until
the magazine clicks into place and ensure that it does
notdisengage.
NOTE: Make sure the forward/reverse control button is set to
forward rotation beforeuse.
5. Refer to DCF6202 Collated Magazine Attachment
Instruction Sheet for furtherinstructions.
Collated attachment (Fig. K)
Optional Accessory
The DCF6202 collated drywall magazine attachment is
designed to be used with your cordless screwgun for
professional driving of collatedscrews.
Installing and Removing the Magazine from the
Screwgun (Fig.K)
NOTICE: For proper operation only use DeWALT
collated screwdriver bit (catalog #:DCF6202PH2).
1. Remove the nose cone from thescrewgun.
2. To remove the bit and bit holder:
a. Grab the bitholder.
b. Push it into the gear case depressing thesleeve.
c. Rotate the bit holder until the clutchengages.
Tool Connect™ Chip (Fig. J)
Optional Accessory
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
Your tool is Tool Connect™ Chip ready and has a location for
installation of a Tool Connect™ Chip.
Tool Connect™ chip
1
communicates with an optional
application for your smart device (such as a smart phone
or tablet) that connects the device to utilize the mobile
application for inventory management functions.
Refer to Tool Connect™ Chip Instruction Sheet for
moreinformation.
Installing the Tool Connect™ Chip
1. Remove the retaining screws
21
that hold the Tool
Connect™ Chip protective cover
22
into thetool.
2. Remove the protective cover and insert the Tool
Connect™ Chip into the empty pocket
23
.
3. Ensure that the Tool Connect™ Chip is flush with the
housing. Secure it with the retaining screws and tighten
thescrews.
4. Refer to Tool Connect™ Chip Instruction Sheet for
furtherinstructions.
Accessories
WARNING:
Since accessories, other than those offered
by DeWALT, have not been tested with this product,
use of such accessories with this product could be
hazardous. To reduce the risk of injury, only DeWALT
recommended accessories should be used with
thisproduct.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact DeWALT call 1-800-4-DeWALT
(1-800-433-9258) or visit our website: www.dewalt.com.
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into aliquid.
Loading ...
Loading ...
Loading ...