Loading ...
Loading ...
Loading ...
49-2001159 Rev. 0
INSTALLATION INSTRUCTIONS
Installation Instructions
INSTALLATION PREPARATION
1. PREPARING FOR INSTALLATION
Positioning the cooktop
The cooktop is designed to look best when centered
LQDFDELQHWDWOHDVWZLGH
7KHH[KDXVWYHQWEHQHDWKWKHFRRNWRSPXVWEH
located between wall studs or floor joists so that the
ductwork may be installed properly.
The downdraft system with blower, motor and
ductwork will occupy the cabinet below the cooktop.
'UDZHUVFDQQRWEHLQVWDOOHGEHORZWKLVFRRNWRS
Avoid placing cabinets above the cooktop unit, if
possible, in order to reduce the hazards caused by
reaching over heated surface units.
If the cabinetry is used above the cooktop, allow
DPLQLPXPFOHDUDQFHEHWZHHQWKHFRRNLQJ
surface and the bottom of the unprotected cabinet.
If the clearance between the cooktop and the
FDELQHWU\LVOHVVWKDQWKHFDELQHWERWWRPPXVW
be protected with a flame retardant millboard at
least
/4WKLFNRUJ\SVXPERDUGDWOHDVW
3
/WKLFN
FRYHUHGZLWKJDXJHVKHHWVWHHORUWKLFN
copper. Clearance between the cooktop and the
protected cabinetry MUST NEVER BE LESS THAN
24".
EXCEPTION: Installation of a listed microwave
oven or cooking appliance over the cooktop shall
conform to the installation instructions packed with
that appliance.
Working areas adjacent to the cooktop should have
DQPLQLPXPFOHDUDQFHEHWZHHQWKHFRXQWHUWRS
and the bottom of the cabinet. If the clearance is
OHVVWKDQ´WKHDGMDFHQWFDELQHWVVKRXOGEHDW
least 5” from the side edge of the cooktop
2. PREPARING THE BASE CABINET
This cooktop is designed to fit easily into a variety
of cabinets. However, the combined installation
of a downdraft vent and a cooktop require careful
consideration.
Some cabinets may require modifications.
This installation requires a 24” min. deep cabinet
base.
7KHFDELQHWPXVWEHDWOHDVW´ZLGH
Preparing a cabinet that is against a wall
In some cabinets, the sides may need to be
VFRRSHGRUFXWGRZQ»´DVVKRZQDQGWKH
corner braces removed in order to accommodate
the unit.
,QFPDQGFPIUDPHOHVV(XURSHDQFDELQHWV
WKHEDFNSDQHOPD\QHHGWREHFXWGRZQ»´WR
accommodate the unit.
Preparing a peninsula or island-type cabinet
In a peninsula or island type cabinet, the sides may
need to be scooped or cut down, and the corner
braces removed in order to accommodate the unit.
PD[
depth of
unprotected
overhead
cabinets
PLQ
clearance from
cutout to side
walls
PLQFOHDUDQFH
from countertop
to unprotected
overhead surface
PLQKHLJKW
from countertop to
nearest cabinet on
either side of the
unit
5
3
»4
”
$SSUR[
5
3
»4
”
$SSUR[
for European
cabinets
3. PREPARING THE COUNTERTOP
The countertop must have a deep flat surface
to accommodate the cooktop and the vent.
Countertops with a rolled front edge and backsplash
may not provide the flat surface area required.
$´ZLGHIODWDUHDLVUHTXLUHGDURXQGWKHHGJH
of opening for support of the unit. The cooktop
unit must be level and sit squarely into countertop
opening.
25” min. flat surface area required
Loading ...
Loading ...
Loading ...