Loading ...
Loading ...
Loading ...
NEW 11/22
4 BD_DH76EF
Owners Manual | BlueDri
®
LGR Dehumidifi er | BD-DH76
TEMPERATURE SETTING
To change unit of temperature, described below:
1. Press MENU once, and screen shows as FIG C, Press SET once, and then MENU once, so the screen shows as FIG D, with an arrow
pointing at the Temperature line.
2. Press SET to select Fahrenheit or Centigrade.
Fig. C Fig. D
AFTER THE JOB
To reduce the possibility of drips when moving the unit, follow these additional steps to ensure that all water is removed from the unit.
NOTICE: To ensure the condensate tank empties completely while purging, make sure the unit is positioned horizontally on a flat surface.
1. Gently rock the machine to ensure any water remaining on interior surfaces falls into the sump area.
2. Press the PUMP key. When the purge cycle is complete, turn the unit off.
3. Remove the external drain hose, drain it carefully, coil it and secure it with one of the Velcro straps provided on the side of the unit.
4. Unplug power cord from power supply and from base of the machine, coil neatly, coil it and secure it with one of the Velcro straps provided
on the side of the unit.
TRANSPORTATION AND STORAGE
NOTICE: Handle the unit carefully. Do not drop, throw, or place the unit where it could fall. Rough treatment can damage this equipment and
may create a hazardous condition or void warranty.
Do not expose the control panel to moisture, snow or rain.
Protect from freezing.
Store and transport securely, and in the upright position, to avoid damaging of internal parts.
Secure during transport to prevent sliding and possible injury to vehicle occupants.
MAINTENANCE SCHEDULE
WARNING! ELECTRIC SHOCK HAZARD. Unplug unit before cleaning or servicing.
WARNING: Risk of dust and contaminants exposure. Use of respirator mask and gloves is recommended. If unit has been exposed to po-
tentially dangerous contaminant, clean thoroughly and sanitize before reuse.
NOTICE: The unit is fitted with sensitive electronic sensors. Protect the sensors and their lead wires from damage and do not expose them
to water or cleaning solution.
Before Each Use Inspect the electrical cord for damage. Look for fraying, cuts, etc. Replace the cord if you find any damage.
Inspect, vacuum or replace filter. Monthly Inspect coils. Clean when dust accumulation is visible. In normal use, dust can accumulate and
can restrict airflow, reducing performance and causing the unit to overheat. Use a vacuum cleaner with a brush tool and a soft cloth to re-
move any debris. Take care not to damage any interior components.
To maintain appearance, wipe interior surfaces with a damp cloth.
Clean Pump Check Valve and Basin If the unit displays the message STATE PUMP, which means the pump may be blocked, check
valve and pump basin may need to be cleaned. This operation must be performed by a qualified technician. Unplug the dehumidifier before
Cleaning . Remove grills and cover. Remove screws from pump base and lift out pump. Wipe out pump basin with a damp cloth. Inspect the
pump base for build-up of debris and clean if needed. Unthread barbed fitting with check valve and rinse fitting and check valve with clean
water. Reinstall check valve into barbed fitting and install the barbed fitting into pump. Do not over-tighten. Reinstall pump in base. Reinstall
cover and grills.
Clean Coils With the cover removed, inspect both coils. If excessive dust and debris is present, vacuum thoroughly and/or clean with coil
cleaner. This operation must be performed by a qualified technician.
MODEL DH76
Power Input 120 Volts, 60Hz
Compressor Power 3/4HP @Aham
Motor Rating: 65W
Current: 6.5 amps
Water Removal 150 Pints/Day @ 90F/90%
76 Pints/Day @ 80F/60%
CFM: 150-190
Weight 65 lbs
Size 22.6x14x20inch
Certifications: cULus
Manuel d’utilisation | Déshumidifi cateur LGR BlueDri
®
| BD-DH76
NEW 11/22
13 BD_DH76EF
MESSAGES DU SYSTÈME
Le système de contrôle DH76 surveille constamment les conditions de fonctionnement internes. Si le système détecte un problème,
la ligne d’état va changer pour afficher un message d’ERREUR au lieu de COMMENCER/ARRÊTER Si l’affichage montre un message
d’ERREUR, débranchez d’abord l’appareil puis branchez-le de nouveau. Cela va normalement réinitialiser les systèmes électroniques et
l’appareil fonctionnera normalement. Si le message d’ERREUR réapparaît, référez-vous à l’explication et à la solution affichée ci-dessous.
Explication du panneau de contrôle et signification du
Message de solution
ÉTAT DU COM-
PRESSEUR
Le compresseur peut ne pas fonctionner, vérifiez le câble du compresseur pour une bonne connexion. Si
l’erreur persiste, contactez le service à la clientèle.
ÉTAT : HUM Vérifiez la température d’entrée/les capteurs d’humidité relative pour une bonne connexion. Si l’erreur per-
siste, contactez le service à la clientèle.
ÉTAT : TEMP 1 Vérifiez la température d’entrée/les capteurs d’humidité relative pour une bonne connexion. Si l’erreur per-
siste, contactez le service à la clientèle.
ÉTAT : TEMP 2 Vérifiez la température de sortie/les capteurs d’humidité relative pour une bonne connexion. Si l’erreur per-
siste, contactez le service à la clientèle.
ÉTAT : POMPE Vérifiez qu’il n’y a pas d’obstruction dans le tuyau de vidange. S’il est obstrué, enlevez le tuyau de l’appareil
et soufflez de l’air comprimé dans le tuyau. Vérifiez et nettoyez le clapet anti-retour et le bassin de la pompe.
DÉPANNAGE
Problème Cause possible Solution possible
Des gouttes d’eau sont tombées
lors du déplacement de l’appareil
L’appareil a été débranché avant que la purge soit finie. Purgez l’appareil en appuyant sur le bouton
de la pompe avant le déplacement. Voir «
APRÈS L’EXÉCUTION » à la page 4.
L’appareil ne fonctionne pas a) L’appareil n’est pas allumé.
b) Lappareil n’est pas alimenté.
a) L’appareil est en tension.
b) Branchez l’appareil, vérifiez que les
connexions du cordon d’alimentation sur
les prises murales et à la base de l’appareil
sont complètement insées et sécurisées.
L’appareil fonctionne, mais la
pièce est toujours humide
a) Pas assez de temps pour la déshumidification.
Peu de mouvement d’air dans la pièce.
b) Infiltration excessive d’air humide.
a) Accordez plus de temps pour la déshu-
midification. Augmentez les mouvements
d’air avec des ventilateurs.
b) Scellez la zone pour réduire l’infiltration.
L’appareil récupère trop peu d’eau a) L’air de la pièce est sec.
b) La température de la pièce est trop froide.
c) Les bobines sont obstruées
d) Le filtre est obstrué.
a) Confirmez le niveau d’humidité avec un
hygromètre.
b) Augmentez la température de la pièce.
c) Vérifiez les bobines. Nettoyez lorsque
c’est nécessaire.
d) Vérifiez le filtre. Nettoyez ou replacez
lorsque c’est nécessaire.
L’appareil ne fonctionne plus
après quelques heures
L’humidité souhaitée est inférieure à l’humidité de
l’environnement.
Baissez l’humidité souhaitée selon le pro-
cessus de PARAMÈTRE D’HUMIDITÉ.
Loading ...
Loading ...
Loading ...