Loading ...
Loading ...
Loading ...
Manuel d’utilisation | Déshumidifi cateur LGR BlueDri
®
| BD-DH76
NEW 11/22
14 BD_DH76EF
Réf Numéro de pièce Description
Quantité
requise
1 DH7601 Grille d’entrée 1
2 DH7602 Préfiltre 1
3 DH7603 Pompe d’eau 1
4 DH7604 Interrupteur de niveau d’eau 1
5 DH7605 Bobine d’évaporation 1
6 DH7606 Compresseur 1
7 DH7607 Bobine de condensateur 1
8 DH7608 Capteur d’humidité 1
9 DH7609 Boîtier supérieur 1
10 DH7610 Panneau de commande 1
11 DH7611 Buse de sortie 1
12 DH7612 Grille de sortie 1
13 DH7613 Ventilateur 1
14 DH7614 Boîtiers électroniques 1
15 DH7615 Boîtier du bas 1
16 DH7616 Câble électrique 1
17 DH7617 Tuyau d’eau 1
Unit Assembly
16
17
NEW 11/22
3 BD_DH76EF
Owner’s Manual | BlueDri
®
LGR Dehumidifi er | BD-DH76
The DH76 Dehumidifier reduces humidity in enclosed structural environments by removing water vapor from the air. With proper use, the
DH76 can help to dry out damp structural materials, insulation, contents, and maintain a healthy level of humidity. Using the DH76 may also
prevent secondary damage caused by high humidity.
SETUP DRAIN HOSE
The DH76 condensation pump connects to a plastic drainage hose. This hose is equipped with a quick- connect fitting for quick attach-
ment to the provided 25 ft. (7.5 m) drain hose. Unwrap the entire hose and place the unattached end in a sink, drain, bucket or outdoors –
anywhere that water can drain out safely. If you use a bucket or other container for water collection, check it regularly to prevent overflows.
NOTICE: Uncoil and straighten the entire drain hose. Do not leave any part of the hose coiled and do not place the end of the hose higher
than 17 ft. (5 m) above the bottom of the unit. Also check for kinks or other obstructions that might restrict the flow of water. Obstructions
may cause a water backup and result in overflows.
DISPLAY MODES
When unit is first plugged in to AC power, the control panel display will briefly cycle through a series of readouts. This is part of the unit’s
self-diagnosis procedure and no user intervention is required.
NOTICE: The DH76 must be plugged into a 120VAC/ 60Hz outlet rated for at least 10 amps. Always plug the cord firmly into the unit first,
and then plug the other end into a suitable wall outlet.
CONTROL PANEL
Power Set
Pump Menu
IN Shows Temp & humidity of the inlet OUT Shows Temp & humidity of the outlet
Cool Shows Temp @ condenser COMP A Shows Amperage Draw of the compressor
Runtime Shows Job hours & life hours STATE Shows the state of the dehumidifier
POWER Press and release to turn unit on or off.
MENU Press to select next item in menu. Menu item will show in display.
SET Press to toggle or select values in menu displayed.
PUMP Press and release to start purge.
HUMIDISTAT SETTING
The default operating mode keeps the dehumidifier running at its maximum capacity. This is ideal for most restoration application. To
control humidity at a specific level, described below:
1. Press MENU once, and screen shows as FIG A, Press SET once so the screen shows as FIG B, with an arrow pointing at the line Moisture line.
Fig. A Fig. B
2. Press SET to adjust the target Moisture, Each press of the button increases the setting by 5% increments, cycling through 90%RH and
starting again at 0%RH.
3. Press MENU once to confirm you %RH, and then two more times to return to the main screen.
Loading ...
Loading ...
Loading ...