Loading ...
Loading ...
Loading ...
ENGLISH
4
Charging Procedure (Fig. A, B)
WARNING: Do not use light while it is connected to
the charging cable.
1. Pull the USB charging port cover
9
away from thelight.
2. Insert the USB charging plug
8
into the charging port
11
.
3. Plug the USB charger plug
7
into any USB charging port
(such as on a computer or wall adapter).
NOTE: Charging takes 1 to 4 hours depending on power
supply rating.
4. The color of the charge indicator LED
10
will be either
red, yellow or green and remain continuously ON
whilecharging.
5. Charging is complete when the color of the charge
indicator LED
10
is green or turns off.
6. The battery can be left charging or the charging cable
can bedisconnnected.
Hot/Cold Delay
When the light detects that the battery is too hot or too cold,
it automatically starts a hot/cold delay, suspending charging
until the battery has reached an appropriate temperature.
The light then automatically switches to charging mode. This
feature ensures maximum batterylife.
1. A cold battery may charge at a slower rate than a
warmbattery.
2. The hot/cold delay will be indicated by the charge
indicator LED
10
will flash red and yellow.
3. Once the battery has reached an appropriate
temperature, the charge indicator LED
10
will show the
color of the current battery capacity, indicating that the
light has resumed the chargingprocedure.
Important Charging Notes
1. The light may become warm to the touch while charging.
This is a normal condition, and does not indicate a
problem. To facilitate the cooling of the light after use,
avoid placing the light in a warm environment such as in
a metal shed or an uninsulatedtrailer.
2. If the light does not charge properly, take the light and
charging cable to your local servicecenter.
3. You may charge a partially used battery whenever you
desire with no adverse effect on thelight
.
aluminum foil or any buildup of metallic particles
should be kept away from the charging plugs and port.
• Always unplug the charging cable from the power
supply when there is no tool attached toit.
Important Safety Instructions for All
Integral Battery Charging
WARNING: Read all safety warnings, instructions,
and cautionary markings for the battery,
charging cable and product. Failure to follow the
warnings and instructions may result in electric
shock, fire and/or seriousinjury.
WARNING: Only charge product using a Listed
Class 2 USB power adapter that is compliant with
applicable country regulations and international/
regional safety standards. Using adapters that do
not meet applicable safety standards could result
in injury.
WARNING: Observe the safety instructions of the
charger being used to charge your device.
• Only use the charging cable supplied by the
manufacturer for charging.
• The provided charging cable is not intended for any
uses other than charging DeWALT rechargeable tools
with
charging
ports. Charging other types of tools may
cause their batteries to overheat and burst, resulting in
personal injury, property damage, fire, electric shock
orelectrocution.
• DO NOT expose charging cable to water, rain orsnow.
• Pull by the plugs rather than the cord when
disconnecting the charging cable. This will reduce the
risk of damage to the plugs andcord.
• Make sure that the cord is located so that it will not
be stepped on, tripped over or otherwise subjected to
damage orstress.
• DO NOT use a charging cable with a damaged cord
orplugs. Have them replacedimmediately.
• Foreign materials of a conductive nature, such as, but
not limited to, grinding dust, metal chips, steel wool,
BATTERIES
The product is not fully charged out of the carton. Before
using the product, read the safety instructions below and
then follow the charging proceduresoutlined.
NOTE: If the product is unused for approximately 90days,
fully charge the battery to help prolong the life of thebattery.
The label on your tool may include the following symbols. The
symbols and their definitions are asfollows:
V ......................... volts
Hz .......................hertz
or DC ......direct current
A ......................... amperes
Ah ....................... amp hours
or AC ...........alternating current
.....................safety alert symbol
.....................class III luminaire
..................... visible radiation
do not stare into
the light
..................... read all
documentation
.....................
do not expose to rain
Additional Safety Rules for Hand Held Lights
• Do not submerge hand held light in anyliquid.
• Do not wash light or battery with water or allow water to
get inside light orbattery.
• Do not operate without lens cover assemblyattached.
Over Temperature Protection (Fig. A)
When over temperature protection is activated, the charge
indicator LED
10
will flash red and green. The unit cannot be
used during the over temperature protection cycle.
State of Charge Indicator (Fig. A)
The DCL182 is equipped with a state of charge indicator. The
charge indicator LED
10
is used to display the current level
of charge in the battery during use and during charging. It
does not indicate tool functionality and is subject to variation
Loading ...
Loading ...
Loading ...