Loading ...
Loading ...
Loading ...
65
USA
Ensure that hair is completely dry before using the ghd
appliance.
ghd original
1 Styler heater plates
2 Raised nger guard. Avoid holding or touching the styler
beyond this feature.
3 On/O Switch and indicator light
4 Styler body
5 Power cord
1. Plug the ghd styler into the power supply. The ghd styler
will momentarily ash around the ON/OFF switch and beep
to indicate that it is connected to a power supply and is in
standby mode.
2. To turn on the ghd styler, press and hold the ON/OFF
button for at least 1 second. The ghd styler will play a
short start-up tune and a light will pulse to indicate that
the styler is heating up.
3. IMPORTANT: The ghd styler reaches the required
temperature in seconds, so be careful not to touch
the heater plates. Once the ghd styler has reached
temperature, it will bleep and the light will remain
illuminated to indicate that it is ready to use.
4. When you have nished your styling session, press and
hold the ON/OFF button until the ghd styler plays the shut-
down tune. Once turned OFF, unplug the ghd styler from
the power supply and allow it to cool in a safe place.
5. For safe cooling always lay your styler on a at heat
resistance surface such as a ghd styler heat mat.
6. WARNING: Upon switching o after a styling session,
the heater plates are still very hot, do not touch the
plates whilst the styler is cooling.
Your ghd styler is not only attractive to you but also
to your children. Please ensure you always store your
ghd styler out of reach of children, especially when
cooling.
The ghd styler has the following safety features:
1. Sleep mode: if the ghd styler has been left on and has
not been used for more than 30 minutes, a safety feature
will automatically turn the styler o. The styler will play
the shut-down tune, the heating plates will start to cool
and the light will slowly pulse.
a. To re-start the ghd styler while it is in sleep mode,
simply re-press the ON/OFF button for at least 1 second
until the start-up tune sounds.
b. Note that although the ghd styler is turned o, it is still
connected to the mains and should be unplugged from
mains electricity at the earliest opportunity.
2. Fail safe: in the unlikely event of a control system error,
for safety the heaters will turn o, the ghd styler will emit
rapid bleeps and the light will ash red every 5 seconds.
If this occurs switch o the ghd styler at the power supply
and re-start. If the unit does not re-start or the problem
persists, contact ghd Customer Service for advice.
user-maintenance
instructions
Cleaning your ghd styler
1. Unplug the ghd styler from the mains power supply.
2. Always allow the ghd styler to cool before attempting
to clean it.
3. Never immerse the appliance in water.
4. Wipe the outside of the ghd styler with a damp cloth.
Do not use sharp or abrasive detergents or corrosive
products.
Storage
1. Always allow the ghd styler to cool down before storing
away.
2. When the ghd styler has cooled down, fold the power cord
in the same way as it was rst delivered in its packaging.
Do not wrap the supply cord around the ghd styler as this
can strain the cord and cause premature supply cord failure.
Failure to operate
Your ghd styling appliance is a high performance product and
if the unit is subjected to large uctuation in mains power
during use it may go into fail-safe mode to protect the unit
from damage. Therefore, in the unlikely event that your ghd
product does not operate correctly, check that your ghd
product and mains power supply are switched on, and that
power is available.
If your product stops working and the white light or red fault
light ashes, please follow the procedure below:
1. Switch o the unit
2. Unplug the unit from the plug socket
3. Wait for 5 seconds and then plug the unit back into
the wall
4. Switch the unit back on If this occurs repeatedly, please
contact your local ghd service centre
If your product is tted with an ALCI plug: If your product
doesn’t switch on, push the yellow test button followed by the
red reset button on the ALCI plug.
If the appliance does not function it must be discarded or
returned to an approved ghd retailer, or you should contact
ghd North America LLC at 877-GHD-ANGEL
(1-877-443-2643) for further instructions.
The appliance has no user serviceable parts.
adapters
For use in other countries a travel adaptor may be required.
A converter is not needed.
manufacturer’s
warranty
All ghd electrical products are individually tested before leaving
the factory. However in the unlikely event of the product proving
defective due to faulty workmanship or materials, then, at its
sole discretion, ghd will replace the product at no charge with
an identical or equivalent product, within two years from the
1
3
2
5
4
Mickey - US - SG - 99200002004.indd 5-6 5/24/2021 5:42:02 PM
Loading ...
Loading ...
Loading ...