Loading ...
Loading ...
Loading ...
9
ENGLISH
1. Press jaw arms
2
to open jaws
1
and place around
thefitting.
2. Turn the tool ON by holding the power ON/OFF button
8
until all three LEDs (
21
,
22
,
23
) illuminategreen.
3. Hold toolsecurely.
4. Press and hold the trigger switch
5
(bottom trigger) until
the cycle is complete, indicated by the ram automatically
returning to its originalposition.
5. When the press cycle is complete, the cycle complete
LED
22
will flash green for five seconds. If the press
cycle is incomplete, the cycle complete LED
22
will flash
red for five seconds. No action is possible until the user
presses the power ON/OFF button
8
.
6. If the battery dies or tool malfunctions during the press
connection, the rollers can retract by pressing the reverse
trigger switch
6
(top trigger). This will retract the ram
and allow the jaws to beopened.
7. Press the power ON/OFF button
8
to turn the tool OFF,
then press the jaw arms to open the jawset.
NOTE: If the tool does not complete the press
properly, read the Troubleshooting Guide or LED
Indications sections or take the tool to a
DeWALT factory
servicecenter.
NOTE: When pressing overhead, always confirm
workpiece and tool are secure beforepressing.
NOTE: In the event of an incomplete press, press the
reverse trigger switch
6
to open the press jaws and
remove thematerial.
Pressing with Press Ring and Actuator
Jaw (Fig.A, D–F)
1. Open ring arms
19
to place open ring
18
around fitting.
2. Press actuator jaw arms
2
to open the actuator jaw
17
and secure into the mating slots
20
of the ring arms
19
.
3. Turn the tool ON by holding the power ON/OFF button
8
until all three LEDs (
21
,
22
,
23
) illuminategreen.
4. Hold toolsecurely.
5. Press and hold the trigger switch
5
(bottom trigger) until
the cycle is complete, indicated by the ram automatically
returning to its originalposition.
6. When the press cycle is complete, the cycle complete
LED
22
will flash green for five seconds. If the press
cycle is incomplete, the cycle complete LED
22
will flash
red for five seconds. No action is possible until the user
presses the power ON/OFF button
8
.
7. If the battery dies or tool malfunctions during the press
connection, the rollers can retract by pressing the reverse
trigger switch
6
(top trigger). This will retract the ram
and allow the jaws to beopened.
8. Press the power ON/OFF button
8
to turn the tool OFF,
then press the actuator jaw arms
2
to open the actuator
jaw
17
and remove from the press ring
18
.
9. Open ring arms
19
to open the press ring
18
and
remove it from thefitting.
NOTE: If the tool does not complete the press properly,
read the LED Indications section or take the tool to a
DeWALT factory servicecenter.
Preparing the Connection
WARNING: Always follow the specific
manufacturer's installation instructions for press
tool attachments being used. It is the installer's
responsibility to ensure the compatibility of the
pipe and fittings used for the connection. Contact
the manufacturer for specific information on their
fittings system. Failure to follow all instructions and
warnings may result in property damage and/or serious
personalinjury.
• Make sure to clear the work area of loose debris and any
other items that could hinder the pressing operation.
• Always ensure the work area is set up properly and that
the tool's connection is prepared according to the fitting
manufacturer’sinstructions.
• Follow the fitting manufacturer’s instructions to make
sure the tubing is inserted properly into thefitting.
Pressing (Fig.A, D–F)
WARNING: To reduce the risk of serious personal
injury, inspect the jaw assembly for cleanliness, cracks
or other damage before beginning a press. Using a dirty
or damaged jaw assembly could result in improper
press connections that could lead to extensive property
damage. Return damaged jaw assembly to a
DeWALT
servicefacility.
WARNING: To reduce the risk of serious personal injury,
prior to use, inspect workpieces for cracks, defects or
wear. Defective workpieces mayshatter.
WARNING: Before turning on the press tool, be
sure hands are clear of thejaws.
Before beginning a press, check the fuel gauge to determine
whether the battery charge is sufficient to complete the
pressingoperation.
NOTE: The tool will turn off automatically after two minutes
of no use.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
Proper hand position requires one hand on the main
handle
15
and one hand on the tool neck
16
, of the
presstool.
Proper Hand Position (Fig.H)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position asshown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
To install the battery pack
10
into the tool handle, align the
battery pack with the rails inside the tool’s handle and slide it
into the handle until the battery pack is firmly seated in the
tool and ensure that it does notdisengage.
To remove the battery pack from the tool, press the release
button
11
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of thismanual.
Loading ...
Loading ...
Loading ...