BD2KITCDIBC INSTRUCTION MANUAL

Loading ...

ENGLISH

Variable Speed Trigger and Forward/

Reverse Control Button (Fig. A)

The tool is turned on and off by pulling and releasing

the variable speed trigger

. The farther the trigger is

depressed, the higher the speed of the tool.

A forward/reverse control button

determines the

rotational direction of the tool and also serves as a

lock-offbutton.

• To select forward rotation (clockwise), release the trigger

and depress the forward/reverse control button on the

right side of thetool.

• To select reverse (counter-clockwise), depress the

forward/reverse control button on the left side of

thetool.

NOTE: The center position of the control button locks the

tool in the off position. When changing the position of the

control button, be sure the trigger isreleased.

NOTE: Continuous use in variable speed range is not

recommended. It may damage the switch and should

beavoided.

Proper Hand Position (Fig. E)



WARNING: To reduce the risk of serious personal

injury, ALWAYS use proper hand position as shown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires one hand on the main

handle

and the other hand holding the battery pack

Installing and Removing the Battery Pack

(Fig. D)

NOTE: For best results, make sure your battery pack is

fullycharged.

To install the battery pack

1

into the tool handle, align the

battery pack with the rails inside the tool’s handle and slide

it into the handle until the battery pack is firmly seated in

the tool and ensure that it does notdisengage.

To remove the battery pack from the tool, press the release

button

2

and firmly pull the battery pack out of the tool

handle. Insert it into the charger as described in the charger

section of thismanual.

OPERATION



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

Symbol Mode

Drilling

1-10 Screwdriving (higher number = greater torque)

Performing an Application (Fig. A)



WARNING: To reduce the risk of personal

injury, ALWAYS ensure workpiece is anchored or

clampedfirmly.



WARNING: Always wait until the motor has come to

a complete standstill before changing the direction

ofrotation.

Prior to Performing Work

• Install the appropriate bit or accessory into the

chuck. Refer to Installing a Bit or Accessory into a

KeylessChuck.



WARNING:

• Do not use this tool to mix or pump easily

combustible or explosive fluids (benzine,

alcohol,etc.).

• Do not mix or stir flammable liquids

labeledaccordingly.

Screwdriving

Your tool has a clutch with adjustable torque for driving

and removing a wide array of fastener shapes and sizes. The

numbers 1–10 on the mode selection collar

5

are used to

set a torque range for screwdriving. The higher the number

on the collar, the higher the torque and the larger the

fastener which can bedriven.

1. Turn the mode selection collar

5

to the

desiredposition. Refer to Mode Selection.

2. Pull the trigger switch applying pressure in a straight

line with the bit until the fastener is seated at the

desired depth in theworkpiece.

Recommendations for Screwdriving

• Start with lower torque settings, then advance to higher

torque settings to avoid damage to the workpiece

orfastener.

• Make some practice runs in scrap or on unseen areas of

the workpiece to determine the proper position of the

mode selectioncollar.

Drilling

IMPORTANT: For MASONRY, such as brick, cement, cinder

block, etc., use carbide-tipped masonrybits.

1. Turn the mode selection collar

to the drillsymbol.

Refer to ModeSelection.

2. Place drill bit in contact with theworkpiece.

NOTE: Use sharp drill bitonly.

3. Pull the trigger switch applying pressure in a straight

line with the bit until it reaches the desireddepth.



WARNING: Drill may stall if overloaded causing a

sudden twist. Always expect the stall. Grip the drill

firmly to control the twisting action and avoidinjury.

Worklight (Fig. A)

The worklight

is activated when the trigger switch is

depressed, and will automatically turn off after the trigger

switch is released. If the trigger switch remains depressed,

the worklight will remainon.

NOTE: The worklight is for lighting the immediate work

surface and is not intended to be used as aflashlight.

Loading ...

INSTRUCTION MANUAL - Page 9