Loading ...
Loading ...
Loading ...
GB
- 38 -
Android: http://qr.einhell.com/176c0443
Use a Bluetooth connection to connect the robot
lawn mower with your smart phone and follow the
steps shown there. You can also use the app to
use the following additional functions of the robot
lawn mower:
•
Rain sensor
The rain sensor (5) can be switched on and
off in the app. The default factory setting for
the sensor is “On”.
•
Multi-starting point
Where gardens have lots of angles the robot
lawn mower may have problems reaching
every part of the lawn and completely mowing
all of it. In this case you can select a number
of starting points on the perimeter wire (18)
with the assistance of the app. This means
that the robot lawn mower will also manage
to get to areas of your garden which are more
difficult to reach. The robot lawn mower will
run the selected distance along the perimeter
wire and then start mowing in this area. (Fig.
9c)
•
Mowing edges
For a tidy lawn edge, the “Edge mowing”
setting can be activated in the app. The robot
lawn mower starts its mowing work every 7
work days by first mowing once along the en-
tire perimeter wire (18). In addition, the robot
lawn mower mows on the way to the charging
station at the end of the daily mowing interval,
if the charge level of the rechargeable battery
is over 70%.
Instructions concerning the Bluetooth con-
nection:
•
Use the Einhell app to establish a connection
to the robot lawn mower.
•
The range of a Bluetooth connection is limi-
ted. This means you must stay close to the
robot lawn mower to control it.
•
The robot lawn mower can be connected to
only one smartphone at a time.
•
Disconnect the Bluetooth connection once
you have made all the settings on the robot
lawn mower.
7. Cleaning, maintenance and
ordering spare parts
Hazard!
The equipment must be disconnected from the
power supply (pull out the power plug and switch
off the equipment by the main switch (7) (OFF)
(Fig. 8) prior to performing any cleaning and
maintenance work.
Caution! Wear work gloves!
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
Do not clean the robot lawn mower with run-
ning water, particularly with high-pressure
water.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may be ag-
gressive to the plastic parts in the equipment.
Ensure that no water can get into the interior
of the equipment.
•
For best results, clean the robot lawn mower
with a brush or rag.
•
Check the freedom of movement of the bla-
des (10) and the blade plate (11)
•
Use cleaning product for metal or very fine
abrasive paper to clean the charging contacts
on the robot lawn mower (1) and the charging
station (19). Clean them in order ensure effici-
ent charging.
7.2 Software update
If you want to update the software, copy the new
software to an empty USB stick (format the USB
stick fi rst if necessary). Make sure that the rechar-
geable battery is fully charged before you carry
out the following steps.
1. Place the robot lawn mower in the area to be
mowed. The robot lawn mower must not be
in the charging station during the software
update.
2. Connect a USB stick to the USB connection
as shown in the illustration. (Fig. 11).
3. Switch on the main switch (7) (ON).
4. Press the POWER button (60) and the “OK”
button (61) at the same time. Keep the but-
tons pressed for 5 seconds. All the LEDs (50,
51, 52, 53) on the control panel will now have
come on (2).
Anl_FREELEXO_BT_SPK9.indb 38Anl_FREELEXO_BT_SPK9.indb 38 12.10.2020 16:55:0412.10.2020 16:55:04
Loading ...
Loading ...
Loading ...