Loading ...
Loading ...
Loading ...
ENGLISH
8
and bike tires, balls, rafts, air mattresses, swimming pool
floats, etc. This product is intended for household, consumer
useonly.
THIS PRODUCT USES THE BATTERY
AND CHARGER LISTED IN THE CHART
BELOW.
Description Catalog Number
20V Max* Lithium-Ion
Battery:
ʵ LBXR20
ʵ LBXR20BT
20V Max* Lithium-Ion
Battery Charger:
ʵ LCS20
ʵ LCS201
ʵ LCS1620
2 Amp Fast Charger: ʵ L2AFC
ʵ L2AFCBST
ʵ LCS200
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source remove the battery pack before
making any adjustments or removing/installing
attachments or accessories. An accidental start-up
can causeinjury.
12V Dc Cord Storage
• Wrap the 12V DC cord around the cord retainer
located in the base of the inflator and snap the 12V
DC connector
14
into its storage location on the
cordretainer.
120V Ac Cord Storage
• Coil the 120V AC cord into its storage location located
on the back of the inflator.
Air Hose Storage
• The high-pressure hose
10
is located in a storage
channel around the face of the unit. Wrap the high-
pressure hose inside the channel.
High-Volume Hose Storage
• The high-volume hose
7
is located in a storage channel
around the back of the unit. Wrap the high-volume hose
inside the channel.
Accessories Storage
• The accessories
16
17
18
are stored in the back of
the unit inside the accessory storage area.
FITTING THE ACCESSORIES
Universal valve adapter (Fig. B)
Your inflator is supplied with the standard tapered nozzle
18
, a brass coupler
17
, and the inflator needle valve
16
,
located on the back of theunit.
• To use the universal valve adaptor
9
, make sure the
lever is in the upposition.
• Place the valve adapter over the stem of the inflator
needle valve, brass coupler adaptor or taperednozzle.
• Press the lever
19
on the universal valve adapter down
to lock it inplace.
• Place the inflator needle valve, brass coupler adapter or
tapered nozzle into the item to beinflated.
NOTE: Always make sure that the lever is in the up position
when not in use. Operate your inflator only with the
universal valve adaptor or with the includednozzles.
NOTE: Make sure the universal valve adapter is firmly
locked in place before turning the inflatoron.
Figure B
18
17
16
19
9
High-volume hose (Fig. C)
• Remove the high-volume hose
7
from the
storagelocation.
• Line up the notches
20
of the hose with the nubs
21
of
the
high volume pump inflator connection
12
. Then,
slide the hose on and twist counter-clockwise tosecure.
• To remove, twist the hose clockwise and slide hoseoff.
Figure C
7
20
21
12
Many inflatables have an internal flap that prevents air loss
during inflation, especially air mattresses. Unless this flap is
displaced by the nozzle the inflatable will not inflate. Push
the nozzle firmly into the valve to make sure that you push
this flap out of theway.
WARNING: Risk of Bursting. Excessive air pressure
may cause a hazardous risk of bursting or personal
injury. Check the manufacturer's maximum pressure
rating for items beinginflated.
NOTE: If the pressure rating for the item being inflated
is above 100 psi, note that the maximum run time is 10
minutes, leave to rest for 20 minutes beforereusing.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from power
source and remove the battery pack before
making any adjustments or removing/installing
attachments or accessories. An accidental start-up
can causeinjury.
Loading ...
Loading ...
Loading ...