Greenworks MO48L520 2 x 24V 48V 21" Brushless Cordless Self-Propelled Lawn Mower, 2 5.0Ah USB Batteries USB Hub and Dual Port Rapid Charger Included

User Manual - Page 12

For MO48L520.

PDF File Manual, 48 pages, Read Online | Download pdf file

MO48L520 photo
Loading ...
Loading ...
Loading ...
5. Use a piece of wood to prevent the movement of the
blade.
6. Remove the mounting nut (18) and spacers (19) with a
wrench or socket.
7. Remove the blade (20).
8. Install the new blade. Make sure that the raised points
engage the holes in the blade.
9. Put in the mounting nut and spacers and tighten them.
Recommended tightening torque: 33-37 N.M.
9.3 STORE THE MACHINE
Clean the machine before storage.
Make sure the motor is not hot when you put the machine
into storage.
Make sure that the machine does not have loose or
damaged parts. If it is necessary, do these steps/
instructions:
Replace the damaged parts.
Tighten the bolts.
Speak to a person of an approved service center.
Store the machine in a dry area.
Make sure that children cannot come near the machine.
You may lower the handle(s) before you put the machine into
the storage.
1. Fully loosen the handle fasteners on the sides of the
handle(s).
2. Fold away the handle(s).
3. Do not pinch or trap the cables.
10 TROUBLESHOOTING
Problem Possible cause Solution
The handle is not
in position.
The bolts are not
engaged correctly.
Adjust the height
of the handle and
make sure that the
knobs and bolts
are aligned cor-
rectly.
The machine does
not start.
The extension ca-
ble is not connec-
ted to the outlet.
Reconnect the ca-
ble.
The extension ca-
ble is not connec-
ted to the power
supply.
Connect the exten-
sion cable to a live
120V AC, 60 HZ
AC receptacle.
The bail switch is
defective.
Replace the bail
switch.
Problem Possible cause Solution
The machine cuts
grass unevenly.
The lawn is rough. Examine the mow-
ing area.
The blade height is
not set correctly.
Move the wheels
to a higher posi-
tion.
The machine does
not mulch correct-
ly.
Wet grass clip-
pings attach to the
deck.
Wait until the
grass dries before
mowing.
The mulch plug is
missing.
Install the mulch
plug.
The machine is
hard to push.
The grass is too
tall, or the blade
height is too low.
Increase the blade
height.
The grass catcher
and the blade
drags in thick
grass.
Empty the grass
clippings from the
grass catcher.
There is a high vi-
bration in the ma-
chine.
The blade is un-
balanced and
worn.
Replace the blade.
The engine shaft is
bent.
1. Stop the en-
gine.
2. Disconnect the
power supply.
3. Inspect for
damage.
4. Repair the ma-
chine before
you start it
again.
The machine stops
during mowing.
The blade height is
too low.
Increase the blade
height.
The grass clip-
pings attach to the
deck or the blade.
Disconnect the
power supply and
check the deck.
Operation temper-
ature of the ma-
chine is too high.
Cool the machine.
* If you cannot find the solution to these problems, go to the
service center.
11 TECHNICAL DATA
Motor 120 V AC, 60 Hz, 13 A
No load speed 3600 RPM
Height adjustments 1 3/8 - 3 3/4” (3.5 - 9.5 cm)
Functions 3-in-1 Mulch & rear bag &
side discharge
12
English
EN
Loading ...
Loading ...
Loading ...