© ®
Single Handle Pull-out Kitchen Faucet
STANDARDS
Tools:
PLUMBERS PUTTY FLASHLIGHT BASIN WRENCH
SAFETY GLASSES SCREWDRIVER
PLIERSCHANNELLOCKS ADJUSTABLE WRENCH
HEX-KEY TAPE
Attention:
Helpful Information
Important
Eliya
2021-06-25 MAAN4251-2
SEALED-TUBE
tools for future use!
1.8 gpm/6.8 L/min
© ®
Single Handle Pull-out Kitchen Faucet
STANDARDS
Tools:
PLUMBERS PUTTY FLASHLIGHT BASIN WRENCH
SAFETY GLASSES SCREWDRIVER
PLIERSCHANNELLOCKS ADJUSTABLE WRENCH
HEX-KEY TAPE
Attention:
Helpful Information
Important
Eliya
2021-06-25 MAAN4251-2
SEALED-TUBE
tools for future use!
1.8 gpm/6.8 L/min
2
3
Installation size map
4.9 in. (12.6 cm)
7.2 in.
(18.4 cm)
17.2 in.
(43.7 cm)
10.3 in. (26.4 cm)
11.5 in. (29.2 cm)
9 in. (23 cm)
9.2 in.
(23.4 cm)
Faucet Installation
Faucet Installation
Remove the rubber, metal washers
and mounting nut from the base by
hand twisting it off.
For 1-hole installation, insert the
faucet through the hole on the sink.
For 3-hole installation, insert the
faucet to the base plate and then
through the hole on the sink.
Note: Make sure that the rubber o-ring
stays above the mounting surface for
1-hole installation or between the
faucet and base plate for 3-hole
installation.
1
Make sure sink installation hole is
1 ³⁄8 inches (3.5 cm).
Rubber
o-ring
Rubber
o-ring
Base
plate
2.4 in. (6.2 cm)
3.5 cm
(1 3⁄8 in.)
2
3
Installation size map
4.9 in. (12.6 cm)
7.2 in.
(18.4 cm)
17.2 in.
(43.7 cm)
10.3 in. (26.4 cm)
11.5 in. (29.2 cm)
9 in. (23 cm)
9.2 in.
(23.4 cm)
Faucet Installation
Faucet Installation
Remove the rubber, metal washers
and mounting nut from the base by
hand twisting it off.
For 1-hole installation, insert the
faucet through the hole on the sink.
For 3-hole installation, insert the
faucet to the base plate and then
through the hole on the sink.
Note: Make sure that the rubber o-ring
stays above the mounting surface for
1-hole installation or between the
faucet and base plate for 3-hole
installation.
1
Make sure sink installation hole is
1 ³⁄8 inches (3.5 cm).
Rubber
o-ring
Rubber
o-ring
Base
plate
2.4 in. (6.2 cm)
3.5 cm
(1 3⁄8 in.)
4
5
6
Secure the faucet by
firmly hand tightening
the rubber washer,
metal washer and
mounting nut back
on the faucet threads
underneath the sink.
Tighten the screws
on the mounting nut
with a Phillips
screwdriver.
Connect the water supply lines to the
hot and cold water valves. Tighten
with an adjustable wrench. Do not
overtighten.
7
Install the spray hose to the outlet
hoses. The outlet will connect with a
simple push. Then attach the weight to
the middle of the spray hose.
Turn the water valves back on and
then turn on the faucet. Run the water
flow for 15 seconds to clean up the
lines and check for any leaks.
The faucet should be flushed for
possible debris prior to using. Remove
the nozzle head by hand twisting it off.
Turn the faucet handle all the way on,
turn on the hot and cold water supply
and flush water lines for one minute.
Re-install the nozzle head by hand
twisting back on.
Attention: Make sure that the inlet
hoses are not twisted.
Cold
supply
hose.
Hot
supply
hose.
Push
Secure the faucet body to the deck
surface with the quick connect base. The
quick connect base will provide a more
stable and secure installation as it
enlarges the contact area with sink.
a
b
General step
Step for top mount stainless steel
sinks or decks smaller than ½ inch
OR
4
5
6
Secure the faucet by
firmly hand tightening
the rubber washer,
metal washer and
mounting nut back
on the faucet threads
underneath the sink.
Tighten the screws
on the mounting nut
with a Phillips
screwdriver.
Connect the water supply lines to the
hot and cold water valves. Tighten
with an adjustable wrench. Do not
overtighten.
7
Install the spray hose to the outlet
hoses. The outlet will connect with a
simple push. Then attach the weight to
the middle of the spray hose.
Turn the water valves back on and
then turn on the faucet. Run the water
flow for 15 seconds to clean up the
lines and check for any leaks.
The faucet should be flushed for
possible debris prior to using. Remove
the nozzle head by hand twisting it off.
Turn the faucet handle all the way on,
turn on the hot and cold water supply
and flush water lines for one minute.
Re-install the nozzle head by hand
twisting back on.
Attention: Make sure that the inlet
hoses are not twisted.
Cold
supply
hose.
Hot
supply
hose.
Push
Secure the faucet body to the deck
surface with the quick connect base. The
quick connect base will provide a more
stable and secure installation as it
enlarges the contact area with sink.
a
b
General step
Step for top mount stainless steel
sinks or decks smaller than ½ inch
OR
A.
B. Turn on water supplies. Check connections for leaks.
C. Remove hand shower and let both hot and cold water
run for one minute. This will help clean any debris that
might otherwise clog the system. Replace hand shower.
D. Operate handle up and down, in cold and hot positions,
to flush water lines thoroughly.
Test Faucet Installation
Simply rinse the surface with clear water or
mild liquid detergents
if necessary Dry the
faucet withaclean soft cotton cloth
Do not
use any cleaning agents containing
acids
polish abrasives or harsh cleaners
Maintenance:
1. Clean it with water and dry it with soft cloth.
2. Clean the product with gentle liquid or glass cleaner.
3. Don't use acid cleaner.
4. Don't clean with abrasive material, abrasive paper or knife.
Parts list
Cleaning and care
Daily cleaning and care are required in order to keep the product shining and working properly.
NO. PART NAM E
Index1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Screw
Handle
Trim cap
Screw nut
Cartridge
Cartridge sleeve
Allen key
Weight
Quick connect base
Deck plate
Deck plate(baseboard)
Spout
Swivel connector
Anticlastic ring
Body
Cartridge base
Sleeve connector
Thread sleeve
O-ring
Washer
Gasket
Screw nut
Screw
Pull-out sleeve
Shower sleeve
Spray head
Aerator wrench
Inlet pipe
Supply line
Single valve
Quick connect components
31
32
Supply line
Pull out hose
33
34
A.
B. Turn on water supplies. Check connections for leaks.
C. Remove hand shower and let both hot and cold water
run for one minute. This will help clean any debris that
might otherwise clog the system. Replace hand shower.
D. Operate handle up and down, in cold and hot positions,
to flush water lines thoroughly.
Test Faucet Installation
Simply rinse the surface with clear water or
mild liquid detergents
if necessary Dry the
faucet withaclean soft cotton cloth
Do not
use any cleaning agents containing
acids
polish abrasives or harsh cleaners
Maintenance:
1. Clean it with water and dry it with soft cloth.
2. Clean the product with gentle liquid or glass cleaner.
3. Don't use acid cleaner.
4. Don't clean with abrasive material, abrasive paper or knife.
Parts list
Cleaning and care
Daily cleaning and care are required in order to keep the product shining and working properly.
NO. PART NAM E
Index1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Screw
Handle
Trim cap
Screw nut
Cartridge
Cartridge sleeve
Allen key
Weight
Quick connect base
Deck plate
Deck plate(baseboard)
Spout
Swivel connector
Anticlastic ring
Body
Cartridge base
Sleeve connector
Thread sleeve
O-ring
Washer
Gasket
Screw nut
Screw
Pull-out sleeve
Shower sleeve
Spray head
Aerator wrench
Inlet pipe
Supply line
Single valve
Quick connect components
31
32
Supply line
Pull out hose
33
34
