Loading ...
Loading ...
Loading ...
8
• Water penetrating the coee machine could cause
damage.
Do not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes.
Do not install the appliance in a room where the tempera-
ture could drop below freezing point.
• Arrange the cord in such a way that it cannot be damaged
by sharp edges or contact with hot surfaces (e.g. electric
hot plates).
• The appliance gives o heat.
After positioning the appliance on the worktop, leave a
space of at least 3 cm between the surfaces of the appli-
ance and the side and rear walls and at least 15 cm above
the coee machine.
Connecting the appliance
Danger!
Check that the mains power supply voltage corresponds to that
indicated on the rating plate on the bottom of the appliance.
Connect the appliance to an eciently earthed and correctly
installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualied
electrician.
FILLING THE WATER TANK
1. Open the lid of the appliance (g. 1) then extract the tank
by pulling upwards (g. 2);
2. Fill the tank with fresh clean water, taking care not to ex-
ceed the MAX level (g. 3).
Put the tank back in the appliance, pressing lightly to open
the valves located on the bottom of the tank.
3. More simply, the tank can also be lled without removing
it, pouring the water directly from a jug.
Important:
Never operate the appliance without water in the tank or with-
out the tank.
Check the level of water in the tank through the viewing win-
dow (A12).
SETTING UP THE APPLIANCE
Important: Everytime you switch on the appliance, make sure that the
mode selector dial (B1) is turned to I position (Stand-by).
1. Turn the appliance on by pressing the ON/OFF button (g.
4): the power light I comes on.
2. Insert the required coee lter in the lter holder (g. 5).
3. Attach the lter holder onto the machine without lling it
with ground coee (g. 6).
4. Place a 0.5 litre container under the boiler outlet and an-
other 0.5 litre container under the cappuccino maker.
5. Wait until the OK light comes on (g. 8) and immediately
afterwards turn the mode selector dial to the
position (g. 9) and deliver about half the tank through the
lter holder.
6. Then turn the steam dial to the position (g. 10)
and deliver all the water remaining in the tank through the
cappuccino maker.
7. Turn the steam dial back to the 0 position and the mode
selector dial to the l position (STAND-BY).
8. Empty the two containers and replace them under the
boiler outlet and the cappuccino maker and repeat points
5-6-7.
Now the appliance is ready for use.
Auto-o
If the appliance is not used for a certain period of time (variable
according to the model), it turns o automatically (the power
light goes out).
Tips for a hotter coee
To make espresso coee at the right temperature, the coee
maker should be preheated as follows:
1. Turn the appliance on by pressing the ON/OFF switch (the
ON light comes on) (g. 4) and attach the lter holder to
the appliance without adding pre-ground coee (g. 6).
2. Place a cup under the lter holder. Use the same cup as will
be used to prepare the coee in order to preheat it.
3. Wait until the OK light comes on (g. 8) and immediately
afterwards turn the selector dial to the position
(g. 9) and let water discharge until the OK light turns o,
then interrupt by turning the dial to the I position.
4. Empty the cup, wait until the OK light comes on again and
then repeat the same operation.
(It is normal for a small and harmless pu of steam to be given
o when removing the lter holder).
Mugs or glasses tray (models ECP35.31 and
ECP33.21 only)
If you are using tall cups or glasses (for example, to make long
coee or macchiato),extract the drip tray and rest the cup di-
rectly on the mugs or glasses tray (A14 - g. 11).
Once you have made your coee, put the drip tray back in
position.
HOW TO MAKE ESPRESSO COFFEE USING PRE-
GROUND COFFEE
Important: Everytime you switch on the appliance, make sure that the
mode selector dial (B1) is turned to I position (Stand-by).
1. Place the ground coee lter (C2 or C3) in the lter holder.
Use the lter to make one coee or the
lter to make two coees.
2. To make just one coee, place one level measure of pre-
ground coee (about 7 g) in the lter. (g. 12).
To make two coees, place two loosely lled measures
(about 6+6 g) of pre-ground coee in the lter.
Fill the lter a little at a time to prevent the pre-ground
coee from overowing.
Important: For correct operation, before lling with pre-ground coee,
make sure there are no coee residues left in the lter from the last time you made
coee.
3. Distribute the pre-ground coee evenly and press light-
ly with the presser (g. 13). Correct pressing of the pre-
ground coee is essential to obtain a good espresso. If
pressing is excessive, coee delivery will be slow and the
froth will be dark. If pressing is too light, coee delivery
will be too rapid and the froth will be skimpy and light
coloured.
4. Remove any excess coee from the rim of the lter holder
and attach to the appliance. Turn the handle rmly to-
wards the right (g. 6) to avoid water leaking out.
5. Place the cup or cups under the lter holder spouts (g.
14). You are recommended to warm the cups before mak-
ing coee by rinsing them with a little hot water.
6. Make sure the OK light (g. 8) is on (if o, wait until
it comes on), then turn the mode selector dial to the
position. When the desired amount of coee
has been delivered, turn the dial to the l position.
7. To remove the lter holder, turn the handle from right to
left.
Danger of burns! To avoid splashes, never remove the lter holder while
the appliance is delivering coee.
8. To turn the appliance o, press the ON/OFF button.
HOW TO PREPARE ESPRESSO COFFEE USING PODS
1. Preheat the appliance as described in the section “Tips for
a hotter coee”, making sure the lter holder is attached.
This obtains a hotter coee.
Please note: Use pods conforming to the ESE standard, indicated on the
pack by the following symbol.
The ESE standard is a system accepted by leading pod producers and enables espresso
coee to be prepared simply and cleanly.
2. Place the pod coee lter (C4 ) in the lter holder.
Downloaded from www.ManualsFile.com manuals search engine
Loading ...
Loading ...
Loading ...