ASSEMBLY & INSTRUCTION MANUAL
INcjh039_US
824-031V80
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
PAGE
2
/
8
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE,
INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND.OTHER BY OBSERVING ALL SAFETY
INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS
COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY
DAMAGE!
IMPORTANT SAFETY INFORMATION
1. Read all instructions carefully before using the FAN.
2. Use this FAN only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, elec
trical
shock, or injury to persons.
3. Remove the package and ensure that the FAN is undamaged. In
case of doubt do not use FAN and contact with your supplier.
4. Do not let children play parts of package.
5. Before use the FAN, check if the voltage marked on the rating
label corresponds to the mains in your home.
6. Extreme caution is necessary when the FAN is used by or near
children or Invalids and whenever the FAN is left operating
unattended.
7. Avoid using extension cord as the extension cord may overheat
and cause a risk of fire.
8. Do not pull the power cord to disconnect with power source.
Always grasp the plug to pull out.
9. Do not insert any objects into the FAN as it may cause an electric
shock or injure or damage to the FAN. Do not block or tamper
with the FAN in any manner while it is in operation.
10. Do not leave the FAN unattended. Always unplug FAN when not
in use.
11. This FAN is not intended for use in wet or damp locations. Never
locate a FAN where it may fall into a bathtub or other water
container.
12. Do not use FAN outdoors.
PAGE
3
/
8
13. Disconnect the fan from the mains power when not in use, and
before servicing or performing any maintenance.
14. This appliance can be used by children aged from 8 years and
above and persons with reduced physical,sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleani
ng and user
maintenance shall not be made by children without supervision.
15. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
16. Regarding how to assemble and maintenance, please refer to
assemble and maintenance section.
17. Always disconnect the fan from the power supply when moving it
from one location to another.
18. Keep the fan clean and maintain in good condition (use
an
authorized service agent).
19. Use recommended parts only (non genuine parts may be
dangerous, and will invalidate your warranty).
20. When not in use store in a safe, dry, childproof location.
WARNING :
To avoid danger of el ectric shock, unplug from
outlet when not in use and before cleaning. If the
supply cord is damaged, it must be replaced by
the manufactory or it’s service a gent or a
similarity qualified person in order to avoid a
hazard.
WARNING :
The Main Power Switch and the On/Off switch
should not be used as the sole means of
disconnecting power. Alw ays unplug the power
cord before ser vicing or moving the unit.
PAGE
4
/
8
PARTS NAME
ASSEMBLY
1. Snap the two parts of the base together and secure with the four
screws using a screwdriver.
2. Line up the Tower fan on the base. Fix with the 4 screws, with a
screwdriver. shown in FIGURE 1.
(Figure 1)
PAGE
5
/
8
REMOTE CONTROL
1. lnstall one ‘mercury’ (not included) batteries.
The Remote Control Power button is labeled as such. All the
functions performed with the Remote Control work identically to the
Manual Controls. ( FIGURE 2).
FIGURE 2
OPERATION
The FAN may be operated by the manual controls located on the
FAN (as shown in FIGURE 3) or by your remote control (shown in
FIGURE 2 ) .
FIGURE 3
1. Place the FAN on a stable flat surface. Plug the cord set into a
120V~AC electrical outlet.
PAGE
6
/
8
POWER: Turn the FAN on by pressing the ‘ ’ button; Turn the
FAN off by touching the ‘
’ button again.
SPEED: You can adjust the fan speed to the desired level: low,
medium, or high by touching ’
’ . The speed setting is displayed
on the FND screen(shown in FIGURE 4) ..
MODE: Touching the ’ ’ button will set the FAN into NORMAL,
NATURAL, and SLEEP mode .
TIMER: The fan is equipped with a timer that allows you to set it's
length of operation from 1 hour to 12 hours. Pressing the ’
’
button.
OSC: Touching the ‘
’ button will start and stop the oscillation
function. The symbol is displayed on the FND screen.
TEMP : Once the unit plug into the power socket or switch on, the
FND will show the room temperature.
LED Lamp : Touching the ‘
’ button will start and close the LED
lamp function.
PAGE
7
/
8
FIGURE 4
Filter installation
1. Insert the filter to the grid.
2. Fix it by 2 screws. See FIGURE 5
FIGURE 5
MAINTENANCE
1. This can only be done by an authorized service agent such as
your local Sealer dealer or any agent qualified to undertake
electrical repairs.
PAGE
8
/
8
2.If the unit requires external cleaning make sure it is switched off
and unplugged from the mains supply. Use a soft tissue or cloth for
general cleaning. To remove more persistent dirt or grime wipe down
with a cloth that has been dampened with warm soapy water. Do not
use any solvents ( such as thinners ) as these may damage the
plastic casing.
notice
1
、
This appliance is not intended for use by persons (including
children) with reduced physical,sensory or mental capa
bilities,or
lack of experience and knowledge,unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
2
、
Children should be supervised to ensure that they do not play
with appliance.
Operating voltage: 120V ~ 60Hz
Power consumption: 50W
