Loading ...
Loading ...
Loading ...
motor specifications and
MOTOR SPECfFICATIONS
This dri!t press is designed to use a _725 RPM rnoto_ orfly.
DO [_ot USeany motor that runs f_iste_ than 17_,:)°r.RPM.
it is wired for operation on 110120 volts, 60 Hz.,
alternating current. 1T MUST NOT BE CONVERTED TO
OPERATE ON 230 VOLTS, EVEN THOUGH THE
RECOMMENDED MOTORS ARE DUAL VOLTAGE.
THESE CRAFTSMAN MOTORS HAVE BEEN
FOUND TO BE ACCEPTABLE FOR USE ON
THIS TOOL.
HP RPM VOLTS CATALOG NO.
1/3 1725 1!0-120 !250
!/2 !725 110-120 1254
1/2 1725 !10-120 1255
1/2 1725 t10-120 1278
1/2 1725 110-120 1279
CAUTION: Do not use blower or washing machme motors
or any motor with an automatic _eset overtoad pTotector as
their use may be hazardous.
CONNECTING TO POWER SOURCE OUTLET
This machine must be grounded white in use to protect the
operator from electric shock_
P!ug power cord into a 110-120V p-opeHy grounded type
outtet protected by a 15-amp, time delay or Circuit-Saver
fuse or circuit breaker.
_F YOU ARE NOT SURE THAT YOUR OUTLET IS
PROPERLY GROUNDED, HAVE IT CHECKED BY A
QUALIFIED ELECTRICIAN.
WARNING: DO NOT PERMIT FINGERS TO TOUCH
THE TERMINALS OF PLUGS WHEN INSTALLING OR
REMOVING THE PLUG TO OR FROM THE OUTLET.
WARNING: tF NOT PROPERLY GROUNDED THIS
POWER TOOL CAN iNCUR THE POTENTIAL HAZARD
OF ELECTRICAL SHOCK, PARTICULARLY WHEN
USED IN DAMP LOCATIONS, iN PROXIMITY TO
PLUMBING. IF AN ELECTRICAL SHOCK OCCURS
THERE _S THE POTENTIAL OF A SECONDARY
HAZARD SUCH AS YOUR HANDS CONTACTING THE
CUTTING TOOL.
If power cord is worn or cut, or damaged in any way, have
it replaced immediately.
3-PRONG
PLUG
PROPERLY _j
GROUNDED
OUTLET
-.,,,
GROU_Dt_dG
PRONG
@
if your unit is for use on less than 150 volts, it has a plug
that looks like above.
eJectrica| requirements
This power tool is equipped with a 3-conductor cord and
groundmg type ptug wh ich has a grounding prong, approved
by Underwriters' Laboratories and the Canadian Standards
Association. The ground conductor has a green jacket and is
attached to the tool housing at one end and to the ground
prong in the attachment p!ug at the other end.
This plug requires a treating 3-conductor grounded type
outlet as shown,
If the outlet you are planning to use for this power tool is
of the:; two prong type DO NOT REMOVE QR ALTER
THE GROUNDING PRONG IN ANY MANNER. Use an
adapter as shown and always connect the grounding lug to
known ground.
It is recommended that you, have a qualified electrician
replace the TWO prong outlet with a properly grounded
THREE prong outlet.
An adapter as shown below is available for connecting plugs
to 2-pror_ 9 receptacles. The green grounding tug extending
from the adapter must be connected to a permanent ground
such as to a properly' grounded outlet box.
GROUNd)! N G LUG
ADAPTER
MAKE SURE THIS tS
3-PRONG CTED TO A
PLUG KNOWN GROUNID
2-PRONG
RECEPTACLE
NOTE: The adapter illustrated is for use only if you already
have a properly grounded 2-prong receptacle. Adapter is
not allowed in Canada by the Canadian Electrica! Code.
The use of any extension cord wilt cause some loss of
power, To keep this to a minimum and to prevent
over-heating and motor burn-out, use the table below to
determine the minimum wire size (A.W.G.)extension cord.
Use only 3 wire extension cords which have 3 prong
grounding type plugs and 3-pole receptacles which accept
the tools plug.
Extension Cord Length Wire Size A.W.G.
Upto- 10OFt. 16
tO0- 200 Ft. 14
200- 400 Ft, 10
CHECK MOTOR ROTATION
WARNING: FOR YOUR OWN SAFETY, MAKE SURE
PLUG IS NOT CONi_IECTED TO POWER SOURCE
OUTLET. WHEN CHANGING MOTOR ROTATION.
The motor must rotate CLOgKW|SE when viewed from the
shaft end to which You will mount the pulley,
if it does not, chef, go the direction according to the
instructions furnished With the motor.
Loading ...
Loading ...
Loading ...