Craftsman 917254750 lawn tractor

User Manual - Page 8

For 917254750.

PDF File Manual, 52 pages, Download pdf file

Loading ...
Loading ...
Loading ...
HOW TO SET UP YOUR TRACTOR
PREPARE BATTERY (See Fig. 2)
, iiill i
CAUTION: Wear eye and face shield°
Wash hands or clothing immediately if
accidentallyin contact with battery acid.
Do not smoke, Fumes from charged
battery acid are explosive,
Read the instructions Included with the
battery vent caps, Always wear gloves,
clothing and goggles to protect your
hands, skin and eyes,
................................... l l, m ....
Your tractor has a battery charging system which is suffi-
cient for normal use However, periodic charging of the
battery with an automotive charger will extend its life_
See instructions packed with vent caps in parts bag.
Fill battery with acid. Fill each celt until it reaches the
bottom of the vent wells Do not overfill
Allow battery to stand and settle for at least thirty
minutes After standing, check the level of acid. If
below the vent wells, add more acid until the correct
levet is reached.
While battery is standing (after adding acid) and later, while
battery is being charged, continue with assembly of tractor
iMPORTANT: TO MAXIMIZE THE LIFE OF YOUR
BATTERY, tT iS NECESSARY THAT THE BATTERY BE
CHARGED BEFORE USE FAILURE TO CHARGE
BATTERY CAN RESULT IN A SHORTENED BATTERY
LIFE
Charge battery at a rate of 6 amperes for 1 hour. Use
a 12 volt battery charger. Observe atl safety precautions
required for battery charging.
Check the acid level after the battery is charged, If the
acid has fallen below the correct level, add distilled or
iron free water.
Install the vent caps to cover the vent wells Wash the
top of the battery with water to remove any acid, then
wipe dry
Check battery case for leakage to make sure that no
damage has occurred in handling.
Dispose of excess battery acid Neutralize acid for
disposal by adding it to four inches of water in a five
gallon plastic container, Stir with a wooden or plastic
paddle while adding baking soda until the addition of
more soda causes no more foaming
Fellow instructions on how to install battery.
cu'r AWAY ViEW r CAP
VENT WELL
BA'r-£ERY
CELLACID
LEVEL
INSTALL SEAT (See Fig. 3)
Adjust seat before tightening adjustment bolt.
Remove cardboard packing on seat pan..
Place seat on pan and assemble shoulder bolt.
Assemble adjustment bolt, lock washer and flat washer
Ioosely_ Do not tighten°
Tighten shoulder bolt securely.
. Lower seat into operating position and sit on seat.
Slide seat until a comfortable position is reached which
allows you to press clutch/brake pedal all the way down
(See Fig° 6),
Get off seat without moving its adjusted position.
Raise seat and tighten adjustment bolt securely.
SEAT
SEAT PAN
SHOULDER
BOLT
ADJUSTMENT
BOLT
i,.
FLAT WASHER
"- LOCK WASHER
FIG, 3
CHECK TIRE PRESSURE
The tires on your tractor were overinflated at the factory for
shipping purposes. Correct tire pressure is important for
best cutting performance,
. Reduce tire pressure PSi shown in "PRODUCT
SPECIFICATION on page 3 of this manual.
CHECK DECK LEVELNESS
For best cutting _esufts, mower housing should be properly
leveled. See TO LEVEL MOWER HOUSING in the
Service and Adjustments section of this manual
CHECK FOR PROPER POSITION OF ALL
BELTS
See the figures that are shown for replacing motion and
mower blade drive belts in the Service and Adjustments
section of this manual Verify that the belts are routed
correctly.
CHECK BRAKE SYSTEM
After you learn how to operate your tractor, check to see
that the brake is properly adjusted. See "TO ADJUST
BRAKE" in the Service and Adjustments section of this
manual.
FIG, 2 8
Loading ...
Loading ...
Loading ...